Abstract:Co-processing of industrial wastes as alternative raw materials in cement manufacture is an example of industrial symbiosis for improved material resource efficiency. Since co-processing introduces impurities from wastes, such as air pollution control residue (APCR) from municipal solid waste combustion, into the cement kiln, a better understanding of their environmental impacts and effects on cement manufacturing and quality is needed. Portland cement clinkers containing 5-35% raw or 5-34% washed APCR were prepared, with formation of all typical minerals, but with effects on clinkering reactions, and increased 2CaO center dot SiO2 and decreased 3CaO center dot SiO2 and 3CaO center dot Al2O3. Raw APCR affected the shape of the 2CaO center dot SiO2 and 3CaO center dot SiO2 grains, and cement paste from clinker made with 35% APCR exhibited negligible 28d strength. Pastes from the clinkers with lower contents of APCR or washed APCR had strengths that were lower than that of the control at 7d, similar at 28d (similar to 90 MPa) and higher at 6 m (up to 120 MPa), consistent with their 2CaO center dot SiO2 and 3CaO center dot SiO2 contents. Utilization of minerals in APCR thus comes with a trade-off against cement quality. Volatilisation of S, Cl, Pb was reduced by washing, which fully eliminated volatilisation of Zn. Zn was found mainly in the interstitial phases of the clinker, in solid solution in 4CaO center dot Al2O3 center dot Fe2O3 or 3CaO center dot Al2O3. Further investigation is required to determine whether Zn and other incorporated elements may be released from the cement paste when these phases react with water. APCR co-processing may reduce CO2 emissions by avoiding CaCO3 decomposition, but this is an uncertain benefit, which may be outweighed by the detrimental effects of APCR alkalis, Cl, S and metals on cement production and quality. Life cycle environmental impacts associated with washing, and dispersal of contaminants in the built environment through construction materials, are additional concerns. (C) 2020 Published by Elsevier Ltd.

Stabilization of Arsenic in Waste During Co-Processing with Cement Kiln and Leaching Characteristics of Clinker

A Comparative Study on Stabilization of Available As in Highly Contaminated Hazardous Solid Waste.

Environmental Safety of Clinker after Co-Processing of Zn Contained Waste

Immobilization of arsenic wastes and retardation effect on cement hydration: Experimental and molecular dynamic analysis

Transformation of Arsenic During Realgar Tailings Stabilization Using Ferrous Sulfate in a Pilot-Scale Treatment.

Risk assessment for the long-term stability of fly ash-based cementitious material containing arsenic: Dynamic and semidynamic leaching

Equilibrium Analysis of Lead in Hazardous Waste During Co-Processing with Cement Kiln

Recycling arsenic-containing bio-leaching residue after thermal treatment in cemented paste backfill: Structure modification, binder properties and environmental assessment

Characterisation of arsenic levels in acid-treated arsenic-containing sludge after steel slag-fly ash gel curing

Effect of Waste Addition Points on the Chromium Leachability of Cement Produced by Co-Processing of Tannery Sludge

An all-in-one strategy for resource recovery and immobilization of arsenic from arsenic-bearing gypsum sludge

Effects of Alkali on Water Soluble Hexavalent Chromium in Ordinary Portland Cement

Co-processing of Raw and Washed Air Pollution Control Residues from Energy-from-waste Facilities in the Cement Kiln

Sustainable stabilization/solidification of arsenic-containing soil by blast slag and cement blends

Mineralogical transformation of arsenic at different copper smelting workshops: The impact on arsenic bioaccessibility

Influence of Sulfur on the Fate of Heavy Metals During Clinkerization

Minimization and stabilization of smelting arsenic-containing hazardous wastewater and solid waste using strategy for stepwise phase-controlled and thermal-doped copper slags

Influence of Chlorine on the Fate of Pb and Cu During Clinkerization

Simulation of heavy metals behaviour during Co-processing of fly ash from municipal solid waste incineration with cement raw meal in a rotary kiln

Mechanistic insights into the leaching and environmental safety of arsenic in ceramsite prepared from fly ash

A novel scheme for safe disposal and resource utilization of arsenic-alkali slag