Abstract:Background Accurate calculation of ventricular stress and strain is critical for cardiovascular investigations. Sarcomere shortening in active contraction leads to change of ventricular zero-stress configurations during the cardiac cycle. A new model using different zero-load diastole and systole geometries was introduced to provide more accurate cardiac stress/strain calculations with potential to predict post pulmonary valve replacement (PVR) surgical outcome. Methods Cardiac magnetic resonance (CMR) data were obtained from 16 patients with repaired tetralogy of Fallot prior to and 6 months after pulmonary valve replacement (8 male, 8 female, mean age 34.5 years). Patients were divided into Group 1 (n = 8) with better post PVR outcome and Group 2 (n = 8) with worse post PVR outcome based on their change in RV ejection fraction (EF). CMR-based patient-specific computational RV/LV models using one zero-load geometry (1G model) and two zero-load geometries (diastole and systole, 2G model) were constructed and RV wall thickness, volume, circumferential and longitudinal curvatures, mechanical stress and strain were obtained for analysis. Pairwise T-test and Linear Mixed Effect (LME) model were used to determine if the differences from the 1G and 2G models were statistically significant, with the dependence of the pair-wise observations and the patient-slice clustering effects being taken into consideration. For group comparisons, continuous variables (RV volumes, WT, C- and L- curvatures, and stress and strain values) were summarized as mean ± SD and compared between the outcome groups by using an unpaired Student t-test. Logistic regression analysis was used to identify potential morphological and mechanical predictors for post PVR surgical outcome. Results Based on results from the 16 patients, mean begin-ejection stress and strain from the 2G model were 28% and 40% higher than that from the 1G model, respectively. Using the 2G model results, RV EF changes correlated negatively with stress (r = -0.609, P = 0.012) and with pre-PVR RV end-diastole volume (r = -0.60, P = 0.015), but did not correlate with WT, C-curvature, L-curvature, or strain. At begin-ejection, mean RV stress of Group 2 was 57.4% higher than that of Group 1 (130.1±60.7 vs. 82.7±38.8 kPa, P = 0.0042). Stress was the only parameter that showed significant differences between the two groups. The combination of circumferential curvature, RV volume and the difference between begin-ejection stress and end-ejection stress was the best predictor for post PVR outcome with an area under the ROC curve of 0.855. The begin-ejection stress was the best single predictor among the 8 individual parameters with an area under the ROC curve of 0.782. Conclusion The new 2G model may be able to provide more accurate ventricular stress and strain calculations for potential clinical applications. Combining morphological and mechanical parameters may provide better predictions for post PVR outcome.

Image-Based Patient-Specific Ventricle Models with Fluid-Structure Interaction for Cardiac Function Assessment and Surgical Design Optimization.

An Approach for Designing Patient-Specific Prosthetic Aortic Valves Based on CTA Images Using Fluid-Structure Interaction (FSI) Method.

In vivo MRI-Based 3D FSI RV/LV Models for Human Right Ventricle and Patch Design for Potential Computer-Aided Surgery Optimization.

Patient-Specific Virtual Surgery for Right Ventricle Volume Reduction and Patch Design Using MRI-Based 3D FSI RV/LV/Patch Models

3D Image-Based Computational Modeling for Patient-Specific Mechanical Analysis of Human Heart Right Ventricles

MRI-Based Patient-Specific Computational Modeling of Right Ventricular Response to Pulmonary Valve Insertion Surgery: A Passive Anisotropic FSI Model with Fiber Orientation

Patient-specific MRI-based 3D FSI RV/LV/patch Models for Pulmonary Valve Replacement Surgery and Patch Optimization.

Using 3d Fsi Rv/Lv Models Based On Patient-Specific Mri Data To Predict Outcome Of Pvi And Rv Volume Reduction Surgeries

Multi-Modality Image-Based Modeling Approach for Cardiovascular Disease: Simulation, Assessment, Prediction, and Virtual Surgery

In Vivo Magnetic Resonance Image-Based 3D Computational Models to Quantify Right Ventricle Morphological and Mechanical Characteristics for Healthy and Patients with Tetralogy of Fallot

A Multiphysics Modeling Approach to Develop Right Ventricle Pulmonary Valve Replacement Surgical Procedures with a Contracting Band to Improve Ventricle Ejection Fraction

Multi-Physics Mri-Based Two-Layer Fluid-Structure Interaction Anisotropic Models of Human Right and Left Ventricles with Different Patch Materials: Cardiac Function Assessment and Mechanical Stress Analysis

3D Fluid-Structure Interaction Canine Heart Model withPatch to Quantify Mechanical Conditions for OptimalMyocardium Stem Cell Growth and Tissue Regeneration

Progress Towards Patient-Specific Computational Flow Modeling of the Left Heart via Combination of Magnetic Resonance Imaging with Computational Fluid Dynamics

Patient-Specific MRI-Based Right Ventricle Models Using Different Zero-Load Diastole and Systole Geometries for Better Cardiac Stress and Strain Calculations and Pulmonary Valve Replacement Surgical Outcome Predictions

Computational modeling of left ventricular flow using PC–CMR–derived four–dimensional wall motion

Intra-ventricular Blood Flow Simulation with Patient Specific Geometry

Image-Based Computational Modeling for Cardiovascular Diseases with Potential Clinical Applications

Patient-specific CT-based 3D Passive FSI Model for Left Ventricle in Hypertrophic Obstructive Cardiomyopathy

Patient-specific in Vivo Right Ventricle Material Parameter Estimation for Patients with Tetralogy of Fallot Using MRI-based Models with Different Zero-Load Diastole and Systole Morphologies.

Patient-Specific Echo-Based Fluid-Structure Interaction Modeling Study of Blood Flow in the Left Ventricle with Infarction and Hypertension