Abstract:PurposeAt the present time, green cutting has become the focus of attention in ecological and environmental protection. Water vapor is cheap, pollution‐free and eco‐friendly. Therefore, it is a good and economical coolant and lubricant. To find the discipline of nozzle diameter, the parameters of water vapor jet flow and cooling distance influence on its lubricating action effect, experiments were carried out in which YT15 (P10 type in ISO) tool was used in cutting C45 steel.Design/methodology/approachThe vapor generator and vapor feed system are manufactured. The temperature and velocity distribution of water vapor jet flow influences the velocity such that water vapor fills up the capillaries and forms the boundary lubricating film layer in the cutting zone, and the temperature and velocity distribution of the vapor jet flow section contains the effective area for the lubricating effect. Through the temperature distribution measured, the empirical formula of temperature distribution is obtained and simulated by Matlab. The turning experiment was carried out according to quantity in cutting υc=45, 60, 75, 90, 105, 120 mm/min, f=0.1 ∼ 0.3 mm/rev, ap=1, 2, 3, 3.5 mm and the jet flow parameters were changed, respectively.FindingsIt was found that: significant decrease of cutting force can be realized with reduced nozzle diameter, increased the sett pressure and shortened the cooling distance. However, reduced to a certain extent it will lead to the increase of the cutting force. The optimal nozzle diameter is 2 mm for the best lubricating effect. The effect on cutting force of the cooling distance is much better than the setting pressure. Significant decrease of friction coefficient of tool‐chip can be realized with reduced nozzle diameter. However, reduced to a certain extent it will lead to the increase of friction coefficient. Significant thinness of chips can be realized by reducing nozzle diameter. But if the diameter is reduced to a certain degree, chips will be thickened. Increased set pressure and shortened cooling distance can both reduce chip thickness, resulting in reduction of chip deformation coefficient. Since water vapor has the advantage of being cheap, pollution‐free and harmless, and there is no need for disposal and recycling, it is ideal for cooling and lubricating technology in green cutting.Originality/valueThe paper establishes the discipline of nozzle diameter, the parameters of water vapor jet flow and cooling distance influence on its lubricating action effect.

Experimental investigation of the effect of ozone in green cutting

Experiments investigation of green cutting with superheated water vapor cooling and lubricating

Experimental Study on Green Cutting with Water Vapor As Coolant and Lubricant

The Investigations of Tool Wear and Wear Mechanism with Water Vapor As Coolants and Lubricants in Green Cutting

Experimental Investigation on Green Cutting GH4169 with Ionized Air Cooling and Lubricating

The Effect of Superheated Water Vapor as Coolant and Lubricant on Chip Formation of Difficult-to-Cut Materials in Green Cutting

Study on Lubricating Characteristic and Tool Wear with Water Vapor As Coolant and Lubricant in Green Cutting

Study on the Effect of Jet Flow Parameters with Water Vapor As Coolants and Lubricants in Green Cutting

Investigation of Water Vapor As Green Coolant and Lubricant in Turning of Austenitic Stainless Steel

The effect of cutting fluids applied in metal cutting process

Experimental Investigation on Tool Wear in Green Cutting Difficult-cut-materials

Research on Difficult‐cut‐material in Cutting with Application of Water Vapor As Coolant and Lubricant

The study on lubrication action with water vapor as coolant and lubricant in cutting ANSI 304 stainless steel

Experimental Investigation on Tool Wear in Dry Electrostatic Cooling Cutting Titanium Alloy TC4

Effect of different cooling and lubrication strategies on milling performance of ultra-high strength steel

Green Cutting of Superalloys as Water Vapor Cooling and Lubricating

Application of ultrasound processing cutting fluids in metal cutting

An Investigation of Organic Mixed Coolant (palm Olein) for Green Machining

Suppression of diamond tool wear with sub-millisecond oxidation in ultrasonic vibration cutting of steel

The Effect of Environmentally Friendly Cooling Techniques in Hard Turning: Comparison of Nanofluid, Vortex, GQDs and Hybrid Cooling Methods

Effect of Ranque-Hilsch Vortex Tube Cooling to Enhance the Surface-Topography and Tool-Wear in Sustainable Turning of Al-5.6Zn-2.5Mg-1.6Cu-0.23Cr-T6 Aerospace Alloy