Electromagnetic Analysis of the Coupler in High Power LHCD System

Li Jun,Liu Fukun

DOI: https://doi.org/10.1109/appeec.2010.5449315

2010-01-01

Abstract:In this paper, electromagnetic characteristic of the coupler in the high power system is analyzed. The eddy current density and the electromagnetic force on the coupler are calculated using 3D Maxwell code by finite element method. The obtained simulation results are presented and discussed.

What problem does this paper attempt to address?

Electromagnetic–Thermo–Mechanical Coupling Behavior of Cu/Si Layered Thin Plate under Pulsed Magnetic Field

Li Qicong,Zhu Linli,Ruan Haihui

DOI: https://doi.org/10.1007/s10338-021-00250-y

2021-01-01

Abstract:Semiconductor-based electronic devices usually work under multiphysics fields rendering complex electromagnetic–thermo–mechanical coupling. In this work, we develop a penalty function method based on a finite element analysis to tackle this coupling behavior in a metal/semiconductor bilayer plate—the representative unit of semiconductor antenna, which receives strong and pulsed electromagnetic signals. Under these pulses, eddy current is generated, of which the magnitude varies remarkably from one plate to another due to the difference in electrical conductivity. In the concerned system, the metal layer generates much larger current, resulting in the large temperature rise and the nonnegligible Lorentz force, which could lead to delamination and failure of the semiconductor-based electronic device. This study provides theoretical guidance for the design and protection of semiconductor-based electronic devices in complex environments.
Characterization Of Near-Field Coupling Effects From Complicated Three-Dimensional Structures In Rectangular Cavities Using Fast Integral Equation Method

Kai Yang,Cheng Ning,Wen-Yan Yin

DOI: https://doi.org/10.1109/TEMC.2016.2620481

IF: 2.036

2017-01-01

IEEE Transactions on Electromagnetic Compatibility

Abstract:This paper characterizes the frequency domain near-field coupling effects from complicated three-dimensional transmission lines, monopole/dipole radiators, and printed circuit boards (PCBs) located in a metallic rectangular cavity with an efficient iterative fast Fourier transform-accelerated integral-equation method. The simulation method combines the rectangular-cavity Green's functions with the frequency-domain electric field integral equation, which is further accelerated by the extension of adaptive integral method for rectangular cavities. By using this method, the near-field coupling effects and internal field distributions are captured and compared with independent references for various structures, including transmission lines, monopole/dipole radiators, and PCBs in rectangular cavities. Numerical results show that strong couplings do appear at multiple resonant frequencies of the structures. In addition, this method can be further employed to mitigate and suppress near-field coupling effects in the optimization of electromagnetic compatibility/interference designs.
Double-Sandwich Magnetic Coupling Structure Design for Dual-LCL Wireless Charging System in EV Applications

Weiyi Huang,Yun Zhang,Fei Gao,Yu Tang

DOI: https://doi.org/10.1109/tvt.2022.3222407

IF: 6.8

2023-01-01

IEEE Transactions on Vehicular Technology

Abstract:In the wireless charging system of EVs, the traditional single-stage LC resonance network has the issues of narrower of parameter design and small equivalent input impedance. While the composite resonant network will introduce additional resonant capacitors and inductors, which increases the system volume, cost, and reduces the efficiency. This paper proposes a design scheme of double-sandwich magnetic coupling structure with a low cross-coupling coefficient, which integrates the resonant inductors into the power transmitter and receiver, and it is designed taking the magnetic leakage and loss as constraints. A 500W prototype is built, and the comparison of experimental efficiencies between the double-sandwich and the separate magnetic coupling structures is performed. Finally, the effectiveness of the integrated design scheme is validated.
Numerical Analysis on Coupling Properties of the LHCD Multijunction Launcher

贾华,秦永亮,刘甫坤,匡光力

DOI: https://doi.org/10.3969/j.issn.0254-6086.2010.01.013

2010-01-01

Abstract:The coupling properties of the Lower Hybrid Current Drive(LHCD) multijunction(MJ) launcher are investigated numerically.The Airy function is used to calculate the plasma impedance and the grill-plasma scattering matrix is deduced,then the coupling properties of the HT-7 LHCD MJ launcher are studied with the antenna scattering matrix and the grill-plasma scattering matrix based on the liner coupling theory.The average power reflection coefficient,directivity,power spectrum are obtained for different edge plasma densities and for different phasings between main waveguides.The results show that the power reflection coefficient of the MJ launcher is much lower and less sensitive to the phase difference than that of the conventional grill because of its self-matching characteristic.However,due to the excrescent side lobe,the current drive efficiency is lower.
Design and Analysis of High-power Third-order 3 dB Directional Coupler

Jiwei QIN,Xiaoguang CHEN,Jihong ZHU

DOI: https://doi.org/10.3969/j.issn.1002-8692.2011.13.011

2011-01-01

Abstract:According to the operation principle and requirements of directional couplers,a third-order 3 dB directional coupler with air as coupling medium is analyzed and designed with the usage of HFSS.On this basis,using a ceramics chip as coupling medium,a high-power third-order 3 dB directional coupler is analyzed and designed.This ceramics consists of Al2O3.On the premise of enough bandwidth,the ceramics chip can improve the capability of voltage resistance of the coupler,and the high-power coupling is achieved.This coupler can be used in the high-power broadcasting transmitter system.
Coupling Comparison of Magnetic Couplers for Mid-range Wireless Power Transfer Systems

Yousu Yao,Zixu Fang,Qinan Ni,Xiufang Liu

DOI: https://doi.org/10.1007/978-981-99-0631-4_21

2023-01-01

Abstract:Mid-range wireless power transfer systems show the advantages of high load-to-source efficiency and long power transfer distance. In this study, the planar circular, planar square, cylindrical, cuboid, circular-cylindrical, and square-cuboid couplers are optimized and compared using finite element simulation. To reduce the ferrite usage, the shielding scheme and ferrite layout of the cylindrical and cuboid couplers are optimized. To improve the coupling coefficient, the key size parameters of the planar circular, planar square, circular-cylindrical, and square-cuboid couplers are optimized. The impact of normalized pad height and distance-to-diameter ratio on coupling coefficient is studied. The coupling coefficients of the six typical mid-range magnetic couplers in different cases are compared. Several design rules for mid-range magnetic couplers are given.
Design of high-power small-size directional coupler

Xiaoguang Chen

2012-01-01

Abstract:With the use of the even-odd mode analysis theory,a third-order 3 dB directional coupler is analyzed and designed by HFSS.On this basis,a ceramics chip is used as coupling medium,and a high-power third-order 3 dB directional coupler is analyzed and designed with the maximum input power above 17 kW.The adding of the ceramic chip can improve the coupler's capability of voltage resistance and cut the size of the directional coupler,therefore high-power small-size coupling is achieved.This coupler can be applied to the high-power broadcasting transmitter system.
Design and Simulation Analysis of Curved Coupler in Wireless Power Transmission System

Qi Li,Jiacheng Li,Ziyu Wang,Bo Pan,Yun Tian,Feng Wen

DOI: https://doi.org/10.1007/978-981-97-0865-9_1

2024-01-01

Abstract:The magnetic coupling resonant transmission method has been widely concerned due to its high transmission efficiency, reliability, convenience, and effectiveness. In this paper, the application of magnetic coupling resonance type wireless power transmission technology in the rocket power supply scenario is studied, and the influence of the operating frequency, the number of transmitter receiver coil turns and the transmission distance changes on the parameters and performance of the curved coupling coil is analyzed. The coupling structure model of the rocket ground Wireless power transfer system is established, and the scheme of curved coupler Wireless power transfer system for the Long March 8 carrier rocket is proposed, which is verified through simulation analysis.
Analysis and Design of Cubic Magnetic Coupler for High Distance-to-Diameter Ratio IPT Systems

Yijie Wang,Peng Gu,Yousu Yao,Dianguo Xu

DOI: https://doi.org/10.1109/tie.2020.3048294

IF: 7.7

2021-01-01

IEEE Transactions on Industrial Electronics

Abstract:This article proposes a kind of cubic-magnetic coupler (CMC) for inductive power transfer (IPT) system, which has huge application potential in the charging field of moving targets. The CMC can still maintain sufficient coupling coefficient when used for long-distance wireless power transfer, it also has great capability of misalignment tolerance. Distance-to-diameter ratio (DDR) is defined to eliminate the impact of coil size and make the comparison between different couplers fairer and easier. This article optimizes the parameters and shape of the CMC. Then, the proposed coupler is compared with several existing couplers employed in long-distance IPT systems. Double-sided LCC compensation topology is chosen to limit the current flowing through the coupling coils. A CMC with an outer size of 180x180x180 mm(3) was made, based on which an IPT prototype was built. The superiorities of the proposed coupler were verified by a series of experiments. When the DDR equals 3, the coupling coefficient of the CMC is 0.00985, and the maximum dc-dc and ac-ac efficiencies are 64.9% and 72.8%, respectively.
Conducted Emi Analysis of Double-Side Lcc Compensated Wpt System

Tianluan Xiao,Wenjie Chen,Heyuan Qi,Zifeng Zhao,Yilin Sha

DOI: https://doi.org/10.1109/apcap.2017.8420703

2017-01-01

Abstract:This paper focuses on the problem of conducted electromagnetic interference (EMI) in double-side LCC compensated wireless power transfer (WPT) system. A high frequency model is established to analyze common mode (CM) and differential mode (DM) conducted EMI at the load side. The investigation is carried out by simulations in Saber taking different factors into account, which consists of the variation of the coupling conditions and load conditions. The comparison of results demonstrates that high coupling coefficient and heavy load cause severe EMI problems.
Design Considerations for Electromagnetic Couplers in Contactless Power Transmission Systems for Deep-Sea Applications

Ze-song Li,De-jun Li,Lin,Ying Chen

DOI: https://doi.org/10.1631/jzus.c0910711

2010-01-01

Journal of Zhejiang University SCIENCE C

Abstract:In underwater applications of contactless power transmission (CLPT) systems, high pressure and noncoaxial operations will change the parameters of electromagnetic (EM) couplers. As a result, the system will divert from its optimum performance. Using a reluctance modeling method, we investigated the gap effects on the EM coupler in deep-sea environment. Calculations and measurements were performed to analyze the influence of high pressure and noncoaxial alignments on the coupler. It was shown that it is useful to set a relatively large gap between cores to reduce the influence of pressure. Experiments were carried out to verify the transferring capacity of the designed coupler and system for a fixed frequency. The results showed that an EM coupler with a large gap can serve a stable and efficient power transmission for the CLPT system. The designed system can transfer more than 400 W electrical power with a 2-mm gap in the EM coupler, and the efficiency was up to 90% coaxially and 87% non-coaxially in 40 MPa salt water. Finally, a mechanical layout of a 400 W EM coupler for the underwater application in 4000-m deep sea was proposed.
Analysis of Electromagnetic Coupling in Hybrid Integrated Power Electronic Module

XJ Zeng,X Yang,ZA Wang

DOI: https://doi.org/10.1109/pesc.2004.1354798

2004-01-01

Abstract:Electromagnetic coupling disturbances have to be given enough attention in the design of hybrid Integrated Power Electronic Module (IPEM) due to the sharply decreased distance between power devices and the control/driving circuits comparing with conventional power electronic equipment built with discrete devices. The high di/dt or high frequency parasitic current ringing is one of important disturbance sources. They can form high frequency circulating current in the bridge circuits and result in the magnetic disturbance by the mutual inductance coupling. A simplified even thin-line division Partial Element Equivalent Circuit (PEEC) approach and image method is applied for mutual inductance calculation and disturbance analysis for an actual half-bridge module test bed. The experiment validates the effectiveness of this evaluation.
Error Analysis of Directional Coupler for Lower Hybrid Wave Power Measurement

Wendong Ma,Lianmin Zhao,Mao Wang,Bojiang Ding,Fukun Liu,Jiafang Shan

DOI: https://doi.org/10.1088/1742-6596/2005/1/012017

2021-01-01

Journal of Physics Conference Series

Abstract:As one of the important parameters for lower hybrid wave (LHW) systems with 24 4.6 GHz/250 kW continuous-wave klystron amplifiers, the microwave power needs to be accurately acquired in real time for the experimental advanced superconducting tokamak (EAST) experiment. A new 4.6 GHz/250 kW directional coupler was developed for power measurements in an LHW system. The design principle and characteristic parameters of the coupler are discussed based on transmission line theory and the system requirements. The calculations and simulations indicate that the measurement error of the incident power is less than 5% when the isolation is greater than 25 dB. The directional coupler was also applied to the 4.6 GHz LHW system. The results show that the device can meet the requirements of LHW system operations. Comprehensive Research Facility for Fusion Technology(CRAFT)is being built. This work is beneficial to the design of power measurement system for LHW system.
A Novel Coupler Design and Analysis with Shielding Material Tests for a CPT System of Electric Vehicles Based on Electromagnetic Resonant Coupling

J Duan,W Wang

DOI: https://doi.org/10.1088/1757-899X/647/1/012005

2019-11-25

IOP Conference Series: Materials Science and Engineering

Abstract:In this paper, a contactless power transfer (CPT) system using a novel geometrically enhanced energy transfer coupler with three different shielding materials has been built and analysed, along with the evaluations from aspects of electromagnetics and RMS power transmitting based on electromagnetic resonant coupling. A CPT system design improvement with the proposed H-shape ferromagnetic cores and the combined semi-enclosed passive electromagnetic shielding methods have been investigated in terms of generated electromagnetic field characteristics, system power transfer ratings, system efficiency optimization and performances of shielding materials. The results have shown that, across the range of operating frequency of the CPT system, aluminium shielding as a metallic material method could deliver better overall CPT system performance than other two ferromagnetic materials, steel 1010 and ferrite. In addition, the coupler prototype design limitations, misalignment tolerance and ...
Design and Analysis of High-power 3 Db-Coupler in Digital Adjacent-channel Duplexer

龙以水,陈晓光,朱继宏

DOI: https://doi.org/10.3969/j.issn.1002-8692.2008.10.008

2008-01-01

Abstract:According to the requirements of 3 dB-coupler in adjacent-channel duplexers and the basic principles of 3 dB-coupler, a narrow band 3 dB-coupler is analyzed which can applied to digital TV field.On this basis, a novel broadband 3 dB-coupler structure is designed, and simulations of this structure are made by the use of HFSS.Design and simulation results show that these two kinds of 3 dB-couplers are consistent with general requirements of parameter indexes, and can be respectively suitable for narrowband and broadband in the adjacent-channel duplexers.
Coupler Conditioning and High Power Testing of ADS Spoke Cavity

Xu Chen,Fanbo Meng,Tongming Huang,Qiang Ma,Haiying Ling,Weimin Pan

DOI: https://doi.org/10.1088/1674-1137/38/2/027001

2013-04-28

Abstract:Power couplers, used in China-ADS proton linac injector I, are required to transfer 6kW RF power to the superconducting Spoke cavities. At present, first two couplers of coaxial design have been fabricated and accomplished high power test at IHEP. The test results indicated that couplers of this design are qualified to deliver 10kW RF power in continuous travelling wave mode. This paper described the coupler's room temperature test procedures and results, discussed the original high power test terminated due to serious out-gassing and after some modifications. In the final test, the couplers smoothly exceeded the design power level.

Instrumentation and Detectors,Accelerator Physics
Analysis of Transmission Characteristics of ECPT System Based on LCLC-LC Compensation

Xin Geng,Jie Xu

DOI: https://doi.org/10.1109/access.2023.3293017

IF: 3.9

2023-07-19

IEEE Access

Abstract:Based on the parameter design of the bilateral LC-type capacitively coupled wireless power transmission system, the T-type LCL impedance network is added to adjust the system voltage gain by adjusting the inductance value in the LCL network at the primary side. The numerical relationship and phase relationship between the output voltage and the input voltage in the resonant state are theoretically derived, and the corresponding mathematical expressions and the calculation expressions of the key parameters of the system are given. Finally, the feasibility and effectiveness of the proposed capacitively coupled wireless power transmission system and its parameter design method are verified by simulation and experiment.

computer science, information systems,telecommunications,engineering, electrical & electronic
High Frequence Structure Simulator Simulation and Performance Analysis for Nearfield and Wide Band Electric Coupling Antenna

Yang Yong,Sun Wei-Qiang,Zhuang Qian-Wei,Feng Tao,Xu Sheng-Yong,Xie Si-Shen

DOI: https://doi.org/10.7498/aps.61.208401

IF: 0.906

2012-01-01

Acta Physica Sinica

Abstract:Electric field coupling antenna is a new type of antenna that can be used in high speed wireless communication at a very short distance. It is the working antenna for Transferjet (TM) technology promoted by Sony Corporation. In this paper, we use the high frequency structure simulator to design a typical antenna of this kind with parametric structures. We analyze the influences of the length (L-s) and width (W-s) of the short stub, the height (H) of coupling electrode on the performance of the antenna corresponding to the centre frequency and bandwidth. We also analyze the effects of the distance (d) and angle (theta) between two antennas and the size of coupling electrode (L-c) on transmission loss. Finally, we design an antenna satisfying the technology standards of Transferjet (TM), thus demonstrate its working performance.
Optimization of underwater contactless power transmission couplers

Wang Haiyang,Li Dejun,Zhou Jie,Li Zesong,Yang Canjun,Chen Ying

DOI: https://doi.org/10.3969/j.issn.2095-2783.2012.08.011

2012-01-01

Abstract:To enhance the transfer capability of an underwater contactless power transmission(CLPT) system,a structure optimization method is proposed for the excitation coils of an underwater electromagnetic coupler.By analyzing parameters in the mutual inductance model and excitation model of the equivalent circuit of the coupler,decomposing the primary current of the coupler into excitation current and reflected current,and analyzing the effects of different turns of excitation coils on the magnetizing inductance and coil resistance,this paper discusses the contradiction between the inhibitory effect of excitation current and the increase of coil resistance loss when the coil turns change.Experimental results show that through the parameter optimization the transmission efficiency and the voltage stability of the CLPT system can be improved effectively.
Coupling Property Analysis of HT-7 Lower Hybrid Current Drive Phased Waveguide Arrays

贾华,秦永亮,刘甫坤,匡光力

2009-01-01

Abstract:Phased waveguide arrays on the HT-7 2.45 GHz lower hybrid current drive(LHCD) system are used to launch the waves into the plasma.Based on the two-dimensional linear coupling theory and the Step + Ramp plasma density profile model,the main coupling property of the launchers was investigated under different kinds of key plasma parameters,such as the edge density,the density gradient and the phasing between adjacent main waveguides.The analysis based on calculation shows that the wave spectrum ranges from 1.93 to 3.15 when the phase between adjacent main waveguides is changed between-90° and 90°.The global average reflection coefficient of the waveguide arrays is below 5% in the range of edge plasma density from 0.5×1018 m-3 to 2×1018 m-3,and the n∥-weighted directivity is rather large.When the adjacent main waveguide phasing varies,the current drive efficiency of the launchers will be affected obviously.

Electromagnetic Analysis of the Coupler in High Power LHCD System

Electromagnetic–Thermo–Mechanical Coupling Behavior of Cu/Si Layered Thin Plate under Pulsed Magnetic Field

Characterization Of Near-Field Coupling Effects From Complicated Three-Dimensional Structures In Rectangular Cavities Using Fast Integral Equation Method

Double-Sandwich Magnetic Coupling Structure Design for Dual-LCL Wireless Charging System in EV Applications

Numerical Analysis on Coupling Properties of the LHCD Multijunction Launcher

Design and Analysis of High-power Third-order 3 dB Directional Coupler

Coupling Comparison of Magnetic Couplers for Mid-range Wireless Power Transfer Systems

Design of high-power small-size directional coupler

Design and Simulation Analysis of Curved Coupler in Wireless Power Transmission System

Analysis and Design of Cubic Magnetic Coupler for High Distance-to-Diameter Ratio IPT Systems

Conducted Emi Analysis of Double-Side Lcc Compensated Wpt System

Design Considerations for Electromagnetic Couplers in Contactless Power Transmission Systems for Deep-Sea Applications

Analysis of Electromagnetic Coupling in Hybrid Integrated Power Electronic Module

Error Analysis of Directional Coupler for Lower Hybrid Wave Power Measurement

A Novel Coupler Design and Analysis with Shielding Material Tests for a CPT System of Electric Vehicles Based on Electromagnetic Resonant Coupling

Design and Analysis of High-power 3 Db-Coupler in Digital Adjacent-channel Duplexer

Coupler Conditioning and High Power Testing of ADS Spoke Cavity

Analysis of Transmission Characteristics of ECPT System Based on LCLC-LC Compensation

High Frequence Structure Simulator Simulation and Performance Analysis for Nearfield and Wide Band Electric Coupling Antenna

Optimization of underwater contactless power transmission couplers

Coupling Property Analysis of HT-7 Lower Hybrid Current Drive Phased Waveguide Arrays