Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Brief introduction of <<Technical Specification of Hollow Concrete-Filled Steel Tubular Structures>> CECS 254:2009

Brief Introduction to Technical Specification of Hollow Concrete-Filled Steel Tubular Structures (CECS 254:2009)

Brief Introduction of "Technical Specification of Hollow Concrete-Filled Steel Tubular Structures " CECS 254∶2009

Seismic Behavior of Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns

The introduction of "technical specification of solid and hollow concrete-filled steel tubular structures"

Concrete-filled Steel Tubes with Reinforcing Bars or Angles under Axial Tension

Flexural Tests and Behavior of Multi-Celled Corrugated-Plate CFST Members

Experimental Investigation and Design of Concrete-Filled Steel Tubular CHS Connections

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Experimental Investigation and Design of Thin- Walled Concrete-Filled Steel Tubes Subject to Bending

Mechanism of Load Introduction and Transfer Within Steel-Encased Concrete-Filled Steel Tube Connections

Experimental Investigation and Design of Hollow Section, Centrifugal Concrete-Filled GFRP Tube Columns

Developments and Advanced Applications of Concrete-Filled Steel Tubular (cfst) Structures: Members

Seismic Performance of Concrete-Filled Steel Tubular (CFST) Structures

Tensile Behaviour of Concrete-Filled Double-Skin Steel Tubular Members

Unified theory on the capability of hollow polygonal CFST compression and bending members

Strength calculation of various centrifugal hollow concrete filled steel tube (H-CFST) members under compression

Effective Stiffness of Rectangular Concrete Filled Steel Tubular Members

Performance of Hexagonal CFST Members under Axial Compression and Bending

Several Key Issues On Modern Concrete-Filled Steel Tubular Structures