Abstract:The development of one-part geopolymer mortars has greater potential than the traditional two-part mortars, especially in repair applications, to convert waste into useful beneficial products while simultaneously eliminating the hazards associated with the alkaline solutions. Nevertheless, the inherent brittleness exhibited by the one-part geopolymers displays drawbacks like OPC when subjected to flexural loading. The fibers selection as well as their strengthening effects from literature is considerably scarce, especially for the repairing geopolymer system. This work aims to investigate the influences of fiber types and volume fractions on the workability, physical behavior, and cracking/fatigue resistance of ambient air-cured one-part geopolymer mortar. Reaction kinetics, mineralogical phases, and elemental components were explored by means of the TAM, quantitative XRD, and EDS mapping analysis. The FESEM and X-CT were employed to compare the microstructures and pore characteristics of the fibers-reinforced products. The results show that the copper-plated steel fiber produced the least change in workability, while the basalt fiber produced the lowest flow values. Setting time was the shortest for the basalt fiber reinforced, followed by polyvinyl-alcohol fiber. The steel fiber and carbon fiber would improve the mechanical properties of mortar significantly, especially in the early stage. The fatigue strength of 1 vol% carbon fiber reinforced mortar under 2 million cycles loading was the highest (3.72 MPa). The fibers addition a substantial decrease in sphericity and compactness of the pores (high anisotropy) as evidenced by X-CT data. Moreover, three hydration heat processes occurred after water was added to the one-part geopolymer mortar, which included dissolution of Na2SiO3 particles, network degradation, and a second pozzolanic reaction. More crystalline formation occurred over curing time to form gel networks with high stability and generated different bonding modes with various fibers.

Setting and Hardening of Geopolymeric Cement Pastes Incorporated with Fly Ash

Critical Features of Microstructure Development of Early-Age Cement Paste Revealed by Non-Contact Electrical Resistivity Measurement

Mechanical behavior and microstructure evolution of slag-fly ash based geopolymer stabilized sand

Effect of Elevated Temperature on Mechanical Properties of High-Volume Fly Ash-Based Geopolymer Concrete, Mortar and Paste Cured at Room Temperature

Mechanical and microscopic properties of fly ash phosphoric acid-based geopolymer paste: A comprehensive study

Performance Characteristics of Micro Fiber-Reinforced Ambient Cured One-Part Geopolymer Mortar for Repairing

Effect of mechanical activation of fly ash on the properties of geopolymer cured at ambient temperature

Reaction Kinetics of Red Mud-Fly Ash Based Geopolymers: Effects of Curing Temperature on Chemical Bonding, Porosity, and Mechanical Strength

The Influence of Particle Size and Calcium Content on Performance Characteristics of Metakaolin- and Fly-Ash-Based Geopolymer Gels

Physico-chemical properties and durability of a fly-ash-based geopolymer

Study of In Situ Foamed Fly Ash Geopolymer

Reverse-diffusion phenomenon of high ductility fly ash-based geopolymer against carbonation

Interfacial Behavior of Slag, Fly Ash, and Red Mud-Based Geopolymer Mortar with Concrete Substrate: Mechanical Properties and Microstructure

Study on the Conductivity and Pressure Sensitivity Performance of Carbon Fiber Geopolymer

The influence of fly ash-based geopolymer on the mechanical properties of OPC-solidified soil

Effects of Steel Slag on Mechanical Properties and Mechanism of Fly Ash–Based Geopolymer

Preparation and curing method of red mud-calcium carbide slag synergistically activated fly ash-ground granulated blast furnace slag based eco-friendly geopolymer

Physical and mechanical properties and micro characteristics of fly ash-based geopolymer paste incorporated with waste Granulated Blast Furnace Slag (GBFS) and functionalized Multi-Walled Carbon Nanotubes (MWCNTs)

Scanning electron microscopy (SEM)-assisted mechanistic study: pH-driven compressive strength and setting time behavior in geopolymer concrete

Designing low-carbon fly ash based geopolymer with red mud and blast furnace slag wastes: Performance, microstructure and mechanism

Efflorescence of fly ash-based geopolymer mortars under quasinatural conditions: The relationship between curing temperature, ion transport, and compressive strength