Thin-layer drying kinetics and quality changes of sweet sorghum stalk for ethanol production as affected by drying temperature
Fei Shen,Lin Peng,Yanzong Zhang,Jun Wu,Xiaohong Zhang,Gang Yang,Hong Peng,Hui Qi,Shihuai Deng
DOI: https://doi.org/10.1016/j.indcrop.2011.05.027
IF: 6.449
2011-01-01
Industrial Crops and Products
Abstract:The chopped sweet sorghum stalk was thin-layer-dried for long-term storage and ethanol production. The drying kinetics and the effects of drying temperature on the qualities of sweet sorghum stalk were investigated in this work. The results showed that the drying process could be simulated well by Wang and Singh's model. The diffusivity constant ( D 0 ) and active energy ( E a ) were estimated as 4.4 × 10 −5 m 2 /s and 21.4 kJ/(mol K) for drying the chopped fresh stalk. According to the sugar composition, browning degree, and fermentability of the dried stalk obtained at various temperatures, the approximate drying temperature could be suggested as 50–60 °C for application. In this range, the moisture of the chopped fresh stalk could drop below the safe moisture for storage in 7–5.5 h with 12.1–9.7% total sugar loss during the drying process. Keywords Sweet sorghum stalk Thin-layer drying Kinetics Quality Ethanol production 1 Introduction Sweet sorghum [ Sorghum bicolor (L.) Moench ] is a high-yielding sugar crop that has many advantages such as wide climate adaptability, tolerance to abiotic stresses like drought, water logging, salinity, and alkalinity ( Li et al., 2010; Rooney et al., 2007 ). Meanwhile, sweet sorghum stalk contains several different soluble (glucose, fructose and sucrose) and insoluble carbohydrates (cellulose and hemicellulose) ( Prasad et al., 2007; Sipos et al., 2009 ). Among the crops currently being actively investigated for bioenergy, sweet sorghum is the most promising one, particularly for bioethanol production ( Gnansounou et al., 2005 ). However, there are a few disadvantages with sweet sorghum. The primary disadvantages are the seasonal availability and short storage duration of the stalk. Consequently, there is high cost associated with long-term storage and seasonal labor requirements ( Bennett and Anex, 2009 ). Especially, storage must be initiated immediately after harvest, because the stalk/juice is rich in soluble sugar and can be easily deteriorated in natural conditions. The previous processing methods mainly focused on the stalk juice storage, such as condensation for syrup (>40%), sterilization by high temperature, storage in low temperature (<−20 °C), and addition of preservatives ( Billa et al., 1997; Mamma et al., 1995; Ning et al., 1995; Shen and Liu, 2010 ). Some researches also focused on the stalk storage technology, such as the atmosphere packaging and SO 2 impregnation ( Eckhoff et al., 1985; Mei et al., 2008 ). A recent study has demonstrated that chopped fresh sweet sorghum stalk was dried in open-air sun conditions, and the dried stalk could be stored well without significant sugar loss for at least 8 months ( Shen and Liu, 2009 ). This offered a practical and effective solution to the storage stream of “soghnol” production on-farm. However, the potential problem for this method was that the drying processes were seriously restricted by the weather during the harvest period. In order to make the storage method more applicable, the forced drying process was considered as an auxiliary way to meet the need of emergency from the unstable weather. Recently, many studies have been reported on thin-layer drying of agricultural products, fruits, and food materials ( Ahmed et al., 2001; Akpinar, 2006; Baini and Langrish, 2007; Doymaz, 2009; Ertekin and Yaldiz, 2004; HacIhafIzoglu et al., 2008; Hassan and Hobani, 2000; Janjai et al., 2011; Mazutti et al., 2010 ). However, the researches about thin-layer drying of chopped sweet sorghum stalk are rather rare. Therefore, it is essential to know the thin-layer drying characteristics and the quality of the dried products. In this context, the main objectives of present work were to investigate the drying kinetics of the chopped sweet sorghum stalk. Meanwhile, the effects of temperature on the qualities of chopped stalk, including sugar composition, browning degree and fermentability, were also investigated to determine an approximate drying temperature. 2 Materials and methods 2.1 Sweet sorghum Sweet sorghum cultivar, Chuntian No 1, was used for this work. The leaves of sweet sorghum were stripped before the fresh stalks were chopped into 4-mm in length using a small scale industry chopping machine (9PR-1.6, Forestry and Agricultural Machinery Plant, Dandong, Liaoning Province, China). The chopped fresh stalk was sealed in a plastic bag in a −20 °C freezer for further use. 2.2 Drying process The chopped fresh stalk (300 g) was dried at temperature of 30 °C, 40 °C, 50 °C, 60 °C, and 70 °C in an air-ventilated oven (DHG9037, Jinghong Instruments Co. Ltd., Shanghai, China) with natural convective airflow of 0.01 m/s. The oven for this work had a similar construction with the referred work ( Hii et al., 2009 ). The chopped fresh stalk was spread thinly in single layer (1.0 cm in thickness) on a meshed tray with 15 cm in diameter. Heat was generated by the heater integrated into the walls of the oven. The exhaust air escaped through a ventilation hole (diameter = 4 cm) at the back of the oven. ∼2.0 g samples were taken periodically from the tray for the measurement of moisture, sugar content and browning degree. 2.3 Moisture content The measurement of moisture content was performed according to the protocol of the standard air oven method ( Jain and Singh, 2000 ). The moisture content calculation was based on the following equation. (1) M ( dry basis ) = W w − W d W d where M is the chopped sweet sorghum moisture content (d.b.), W w is the wet weight and W d is the dried weight of the sample. Experiments were conducted in triplicate. 2.4 Sugar content The sugars in chopped sweet sorghum stalk, including sucrose and reducing sugars (glucose + fructose), were determined by DNS (3,5-dinitrosalicylic acid) method. The detailed protocol for sugar extraction from stalk and the further analysis were based on Shen and Liu (2009) . 2.5 Browning degree (BD) The protocol for BD determination was according to Wang et al. (2006) . The samples for the BD determination were obtained from the step of the extraction before the sugar determination. The extracted liquid was diluted properly and measured at the absorbance of 420 nm with a spectrophotometer (Unico-2000, Unico Instruments Co., Ltd., Shanghai, China) using 10 mm path length cells. 2.6 Fermentability The dried stalk was ground in 2.5–2.8 mm and rehydrated in high pressure sterilization with 121 °C for 10 min. In order to make a comparison on the fermentation between fresh stalk and dried stalk, a suitable amount of water should be supplemented for rehydration. The amount of water supplemented for rehydration could be calculated according to the difference of moisture content between the fresh and dried stalk. Solid state fermentation was employed for the evaluation of fermentability. 50.0 g rehydrated stalk was used as the substrate. The cell inoculation rate of 1‰ (wt/wt) dry active yeast (Angel Yeast Co., Ltd. Yichang City, Hubei Province of China, China) was inoculated for ethanol fermentation, and no extra nutrients were supplemented. The fermentation was carried out in cylinder flasks with the inoculation temperature of 35 °C for 48 h. The final ethanol was detected using a GC (SHIMADZU 2010, Shimadzu Corporation, Japan) after the ethanol extraction according to the description in Shen and Liu (2009) . The ethanol yield was applied for the comparison of fermentability in different treatments. It was defined as the following equation. (2) Ethanol yield ( % ) = Ethanol content 0.51 Total sugar content × 100 % where ethanol content refers to the obtained ethanol in substrate after fermentation (mg/g stalk, dry basis). Total sugar content refers to the total soluble sugar in fermentation substrate (mg/g stalk, dry basis). 2.7 Mathematical modeling of the thin-layer drying kinetics For investigation of drying characteristics of the chopped stalk, it is important to try to represent as accurate as possible the drying behavior. In this work, the experimental drying data at different temperatures were fitted using 9 classical thin-layer drying models, listed in Table 1 ( Akpinar et al., 2003; Ayensu, 1997; Midilli et al., 2002; Torul and Pehlivan, 2002; Wang et al., 2007; Yaldiz et al., 2001 ). In these models, MR represents the dimensionless moisture ratio (d.b.), namely: (3) MR = ( M − M e ) ( M 0 − M e ) where M is the moisture content of the stalk, M 0 is the initial moisture content of the fresh stalk and M e is the equilibrium moisture content. Statistical parameters such as the correlation coefficient ( R 2 ), chi-square ( χ 2 ) and the root mean square error (RMSE) were used to assess the goodness of fitting. Generally, the higher R 2 and the lower χ 2 and RMSE values are, the better model fitting is. The chi-square ( χ 2 ) and RMSE could be calculated as follows: (4) χ 2 = ∑ i = 1 N ( MR exp , i − MR pred , i ) 2 N − z (5) RMSE = 1 N ( MR exp , i − MR pred , i ) 2 where MR exp, i and MR pred, i are the i th experimental and predicted moisture ratio, respectively. N is the number of observations and z is the number of parameters. In this work, the nonlinear or linear regression analysis and the calculation of mentioned statistical parameters were performed using the software of Matlab V7.1 R14 (the MathWorks, Inc. Natick, MA, USA). 2.8 Effective diffusivity and activation energy It has been accepted that the drying characteristics of biological products in falling rate period could be described by Fick's diffusion equation. The solution to this equation developed by Crank could be used for various regularly shaped bodies such as rectangular, cylindrical and spherical products. The form of Eq. (6) could be applicable for particles with slab geometry by assuming uniform initial moisture distribution ( Crank, 1979; Mazutti et al., 2010 ). (6) MR = 8 π 2 ∑ n = 0 ∞ 1 ( 2 n + 1 ) 2 − ( 2 n + 1 ) 2 π 2 D e f f t 4 L 0 2 where D eff is the effective diffusivity (m 2 /s) and L 0 is the half thickness of slab (m). For long drying time, Eq. (6) could be further simplified to retain only the first term. It could be rewritten as Eq. (7) in a logarithmic form ( Mazutti et al., 2010 ). Diffusivity could be typically determined by plotting experimental drying data in terms of ln MR versus drying time in Eq. (8) , and calculated by the slope of the providing a straight line. (7) ln MR = ln 8 π 2 − π 2 D eff 4 L 0 2 t The effective moisture diffusivity could be related with temperature by simple Arrhenius equation as given below ( Arumuganathan et al., 2009 ): (8) D eff = D 0 exp − E a R T where D eff is the effective moisture diffusivity (m 2 /s), D 0 is the constant equivalent to the diffusivity at infinitely high temperature (m 2 /s), E a is the activation energy (kJ/mol), R is the universal gas constant (8.314 J/(mol K)), and T is the absolute temperature (K). The activation energy ( E a ) and the constant ( D 0 ) could be determined by plotting ln( D eff ) versus 1/ T after linearization for Eq. (8) . 3 Results and discussion 3.1 Drying kinetics of chopped stalk The initial moisture content (d.b) of the chopped sweet sorghum stalk was 3.71 ± 0.13 (mean ± SD). The experimental data (moisture content vs. time) in drying process were shown in Fig. 1 . As expected, the drying temperature had a significant effect on the drying rate of the samples. The moisture content decreased continuously with time and an increase in temperature resulted in the reduction of total drying time. The longest and shortest drying time were recorded at 24 h (30 °C) and 10 h (70 °C), respectively. According to a previous work ( Shen and Liu, 2009 ), the safe moisture content (d.b.) for sweet sorghum stalk storage was lower than 0.28. Thus, the actual drying time to reach the safe moisture content could be determined at 16 h, 9.5 h, 7 h, 5.5 h, and 4.5 h when the temperature was set at 30 °C, 40 °C, 50 °C 60 °C and 70 °C. Additionally, the temperature also drastically affected the equilibrium moisture. The equilibrium moisture contents were determined to be 0.109, 0.044, 0.035, 0.025 and 0.022, respectively, with the increasing of temperature from 30 °C to 70 °C. According to the presented data, the drying kinetics using various classical models were investigated. The statistical results were listed in Table 2 . According to the values of R 2 in different models at various temperature, it could be found the R 2 in Model 2, 5, 6, 7, and 9 at various drying temperature were all higher than 0.99 except Model 2 and Model 6 in 30 °C. The results indicated that the mentioned 5 possible models could fit the experimental data well. In addition, For Model 2 and 6, the R 2 values at 30 °C were lower than 0.99, but it increased with the drying temperature. This meant that Model 2 and Model 6 were more suitable to describe the process in high drying temperature zone. Based on the mean value of statistical parameters (MSP) of these 5 models at various temperatures, the highest MSP of R 2 and lowest χ 2 and RMSE appeared in model 9, which indicated that the Wang and Singh's model was the best one to stimulate the experimental data. Hence, the Wang and Singh's model could be selected in the present work to predict the drying characteristics of chopped sweet sorghum stalk. To take into account the effects of drying temperature on the model parameters, namely a , b and c in Model 9, and attempting to generalize the model, a regression analysis was applied to set up the relationship between these parameters and the temperature. The regression equations of these parameters against drying temperature (K) for each experimental condition were presented in Table 3 . The relationship between parameter of “ a ” and temperature ( T ) could be described using a cubic polynomial with correlation coefficient ( R 2 ) of 0.9335. The parameters of “ b ” and “ c ” could relate with drying temperature ( T ) using the linear regression with the R 2 of 0.9902 and 0.9913, respectively. In order to check the validation of the generalized model, the comparison of experimental moisture ratio values and the predicted values at various particular drying temperatures was carried out. Results showed that these experimental values laid near the straight lines (shown in Fig. 2 ), which suggested that the generalized model was valid at drying temperatures of 30–70 °C for drying sweet sorghum stalk. The effective diffusivity could be determined after the linearization of Eq. (6) in the form of Eq. (7) . According to the regression between the experimental ln MR in falling rate period and the corresponding time ( s ), the effective diffusivities ( D eff ) were 7.20 × 10 −9 m 2 /s, 9.95 × 10 −9 m 2 /s, 1.33 × 10 −8 m 2 /s, 1.76 × 10 −8 m 2 /s and 1.91 × 10 −8 m 2 /s at the temperatures of 30 °C, 40 °C, 50 °C, 60 °C and 70 °C, respectively. It could be obviously found the D eff s increased as the temperature increased. These D eff s were all in a reasonable range compared with the thin-layer drying of sugarcane bagasse ( Mazutti et al., 2010; Vijayaraj et al., 2007 ). The logarithm of D eff as a function of the reciprocal of absolute temperature was plotted in Fig. 3 . The results showed a linear relationship between (ln D eff ) and (1/ T ), leading to an Arrhenius-type relationship between the diffusion coefficient and temperature. According to Fig. 3 , the R 2 for the regression was 0.9779. Thereby, the diffusivity constant D 0 could be calculated as 4.4 × 10 −5 m 2 /s. The active energy ( E a ) for moisture diffusion in drying the chopped stalk also could be estimated as 21.4 kJ/(mol K). The E a value was higher than some typical agricultural residues such as corn stalk, rice straw ( Cai and Chen, 2008 ), and lower than that of the apple slices, red chillies and salak ( Aghbashlo et al., 2010; Kaleemullah and Kailappan, 2006; Ong and Law, 2009 ). However, the E a of sweet sorghum stalk closed to that of sugarcane bagasse with a little higher ( Vijayaraj et al., 2007 ). The main reasons were probably due to the difference of their constructions and the initial moisture contents of these materials. For example, activation energy for sample (salak) with surface membrane was found higher than those without surface membrane and further resisted the moisture movement ( Ong and Law, 2009 ). 3.2 Effects of drying temperature on the qualities of chopped stalk The total sugar in sweet sorghum stalk mainly included sucrose, glucose and fructose, in which glucose and fructose were generally regarded as the reducing sugar. The purpose for drying sweet sorghum stalk was to prolong the storage and preserve more sugar. Therefore, the sugar composition changes at various drying temperature were necessary to be investigated. According to Fig. 4 , the total sugar loss actually happened in all groups after drying compared with the fresh stalk. The degree of total sugar loss was obviously reduced when the drying temperature increased from 30 °C to 70 °C. For the sucrose, it decreased slightly in 30 °C and 40 °C, and then decreased significantly when the temperature was enhanced from 50 °C to 70 °C. On the contrary, the reducing sugar at different drying temperatures slightly increased from 30 °C to 40 °C, and significantly increased from 50 °C to 70 °C. According to the results, it could be deduced that the possible reasons for sugar loss might mainly be from two aspects. The first aspect was the sugar consumption by microorganisms when the drying temperature was lower than 40 °C. Because the drying temperature of 30–40 °C was a suitable range for the growth of most microorganisms. The other aspect was the sugar degradation by browning reaction, including enzymatic and non-enzymatic browning. As shown in Fig. 5 , the browning reaction could happen in 30 °C and 40 °C. Moreover, the higher temperature was applied for drying, the more serious browning reaction could happen. Generally, the enzymatic browning always seriously happened in temperature lower than 40 °C. Once the drying temperature was higher than 40 °C, the non-enzymatic browning will occur heavily with temperature increase. Consequently, the total sugar loss in low temperature range was thereby more serious than high temperature, because the co-action of microorganisms’ consumption and browning reaction. Most microorganisms could not grow when the temperature was higher than 50 °C, and the enzymatic browning also could be weakened. Thus, the sugar loss in high temperature mainly came from non-enzymatic browning reaction. Additionally, the hydrolysis of sucrose into the reducing sugar could also be occurred during the drying process ( Shen and Liu, 2010 ). Moreover, the hydrolysis could be accelerated with the increasing of temperature. Hence, the reducing sugar in drying process was in a trend of increase as the temperature increased from 50 °C to 70 °C, and sucrose was in a trend of decrease with increasing temperature. 3.3 Effects of drying temperature on the fermentability of the dried stalk The ethanol production was the final purpose to the storage of sweet sorghum stalk in drying way. The dried stalk was sequentially fermented after rehydration to investigate their fermentability. The results were presented in Fig. 6 . 58.5% of ethanol yield in the fresh stalk could be obtained after 48 h fermentation. It was unexpected that ethanol yield in the fresh stalk was lower than any groups of the rehydrated dry stalk. Moreover, The ethanol yield increased slightly from 65.5% to 73.3% when the drying temperature increased from 30 °C to 50 °C. Afterward, it dropped to 70.6% when the drying temperature increased to 70 °C. The dried stalk obtained at 60 °C had the highest ethanol yield. According to these results, it could be found that the dried sweet sorghum had a better fermentability after rehydration in contrast to fresh stalk. In previous studies, it was showed that the drying temperature would result in the losses of cell wall materials of kiwifruit, including pectin and hemicellulose, in the temperature range of 30–90 °C ( Femenia et al., 2009 ). Moreover, the amorphous cellulose could be partly rearranged or degraded in much higher temperature ( Sik et al., 2010 ). These indicated that the drying temperature could destroy the cell wall structure in a degree, which would be beneficial for the solubilization and diffusion of the sugar inside cell to the surface, and further improve the accessibility of sugars to yeast. Therefore, the ethanol yield of the rehydrated stalk could be higher than the fresh one. In addition, the drying temperature could reduce the hygroscopicity of lignocellulosic materials ( Sik et al., 2010 ). Thus, some free water could be observed around the substrate after suitable amount water was supplemented for rehydration to achieve the same water content with fresh stalk. Moreover, the higher temperature was applied for drying, the more free water could be observed after the rehydration. The existence of free water in solid state fermentation might be beneficial to the sugar/nutrition materials transportation from substrate to yeast cell and the ethanol transportation from yeast cell ( Shen and Liu, 2009 ). However, for the fresh stalk, there was no free water in the fermentation system. Therefore, the existence of free water could be a reason for a higher fermentability in rehydrated substrate. Additionally, based on the results in Fig. 5 , the browning degree was increased by the drying temperature, which could probably result in the formation of some potential inhibitors. This might be the reason for the ethanol yield decreased slightly when the dried stalk obtained at 70 °C was used for fermentation. As discussed above, the higher temperature could be beneficial to reduce the total sugar loss, but the excessive high temperature will bring the potential risk of the fermentation inhibition resulting in the decrease of ethanol yield. Hence, the suitable drying temperature could be selected as 50–60 °C. In this temperature range, the moisture content (d.b.) of fresh sweet sorghum could drop below 0.28, which was thought as the safe moisture for sweet sorghum storage, in 7–5.5 h with 12.1–9.7% total sugar loss during the drying process. 4 Conclusions Nine models were simulated to determine the approximate one for the drying process description. Meanwhile, the qualities, including sugar composition and the fermentability, were also investigated at different drying temperatures. The results showed that the Wang and Singh's model was the best one to describe the drying process of the chopped sweet sorghum stalk. The diffusivity constant ( D 0 ) and active energy ( E a ) could be, respectively, estimated as 4.4 × 10 −5 m 2 /s and 21.4 kJ/(mol K) for drying the chopped sweet sorghum stalk. Combining the analysis of qualities, the approximate drying temperature could be suggested as 50–60 °C for the application. Acknowledgements We appreciate Professor Mengjie Wang, in the Chinese Academy of Agricultural Engineering, who kindly provided the seed of the sweet sorghum cultivar Chun Tian No.1 in the study. We also give our appreciation to Michael LY Liu in the University of British Columbia, Canada, for the language revision for the paper. References Aghbashlo et al., 2010 M. Aghbashlo M.H. Kianmehr A. Arabhosseini Modeling of thin-layer drying of apple slices in a semi-industrial continuous band dryer Int. Food Eng. 6 2010 1 15 Ahmed et al., 2001 J. Ahmed U.S. Shivhare G. Singh Drying characteristics and product quality of coriander leaves Food Bioprod. Process. 79 2001 103 106 Akpinar, 2006 E.K. Akpinar Determination of suitable thin layer drying curve model for some vegetables and fruits J. Food Eng. 73 2006 75 84 Akpinar et al., 2003 E.K. Akpinar Y. Bicer C. Yildiz Thin layer drying of red pepper J. Food Eng. 59 2003 99 104 Arumuganathan et al., 2009 T. Arumuganathan M.R. Manikantan R.D. Rai S. Anandakumar V. Khare Mathematical modeling of drying kinetics of milky mushroom in a fluidized bed dryer Int. Agrophys. 23 2009 1 7 Ayensu, 1997 A. Ayensu Dehydration of food crops using a solar dryer with convective heat flow Sol. Energy 59 1997 121 126 Baini and Langrish, 2007 R. Baini T.A.G. Langrish Choosing an appropriate drying model for intermittent and continuous drying of bananas J. Food Eng. 79 2007 330 343 Bennett and Anex, 2009 A.S. Bennett R.P. Anex Production, transportation and milling costs of sweet sorghum as a feedstock for centralized bioethanol production in the upper Midwest Bioresour. Technol. 100 2009 1595 1607 Billa et al., 1997 E. Billa D.P. Koullas B. Monties E.G. Koukios Structure and composition of sweet sorghum stalk components Ind. Crop. Prod. 6 1997 297 302 Cai and Chen, 2008 J. Cai S. Chen Determination of drying kinetics for biomass by thermogravimetric analysis under nonisothermal condition Dry Technol. 26 2008 1464 1468 Crank, 1979 J. Crank The Mathematics of Diffusion 1979 Oxford University Press USA Doymaz, 2009 I. Doymaz Thin-layer drying of spinach leaves in a convective dryer Food Bioprod. Process. 32 2009 112 125 Eckhoff et al., 1985 S.R. Eckhoff D. Bender M.R. Okos R.M. Peart Preservation of chopped sweet sorghum using sulfur dioxide Trans. ASAE 28 1985 606 609 Ertekin and Yaldiz, 2004 C. Ertekin O. Yaldiz Drying of eggplant and selection of a suitable thin layer drying model J. Food Eng. 63 2004 349 359 Femenia et al., 2009 A. Femenia G. Sastre-Serrano S. Simal M.C. Garau V.S. Eim C. Rossell Effects of air-drying temperature on the cell walls of kiwifruit processed at different stages of ripening LWT-Food Sci. Technol. 42 2009 106 112 Gnansounou et al., 2005 E. Gnansounou A. Dauriat C.E. Wyman Refining sweet sorghum to ethanol and sugar: economic trade-offs in the context of North China Bioresour. Technol. 96 2005 985 1002 HacIhafIzoglu et al., 2008 O. HacIhafIzoglu A. Cihan K. Kahveci Mathematical modelling of drying of thin layer rough rice Food Bioprod. Process. 86 2008 268 275 Hassan and Hobani, 2000 B.H. Hassan A. Hobani Thin-layer drying of dates J. Food Process Eng. 23 2000 177 189 Hii et al., 2009 C.L. Hii C.L. Law M. Cloke Modeling using a new thin layer drying model and product quality of cocoa J. Food Eng. 90 2009 191 198 Jain and Singh, 2000 P. Jain P. Singh Moisture determination of jaggery in microwave oven Sugar Technol. 2 2000 51 52 Janjai et al., 2011 S. Janjai M. Precoppe N. Lamlert B. Mahayothee B.K. Bala M. Nagle J. Müller Thin layer drying of litchi ( Litchi chinensis Sonn .) Food and Bioprod 89 2011 194 201 Kaleemullah and Kailappan, 2006 S. Kaleemullah R. Kailappan Modelling of thin-layer drying kinetics of red chillies J. Food Eng. 76 2006 531 537 Li et al., 2010 B.Z. Li V. Balan Y.J. Yuan B.E. Dale Process optimization to convert forage and sweet sorghum bagasse to ethanol based on ammonia fiber expansion (AFEX) pretreatment Bioresour. Technol. 101 2010 1285 1292 Mamma et al., 1995 D. Mamma P. Christakopoulos D. Koullas D. Kekos B.J. Macris E. Koukios An alternative approach to the bioconversion of sweet sorghum carbohydrates to ethanol Biomass Bioenergy 8 1995 99 103 Mazutti et al., 2010 M.A. Mazutti G. Zabot G. Boni A. Skovronski D. De Oliveira M. Di Luccio J.V. Oliveira M.I. Rodrigues H. Treichel F. Maugeri Mathematical modeling of thin-layer drying of fermented and non-fermented sugarcane bagasse Biomass Bioenergy 34 2010 780 786 Mei et al., 2008 X.Y. Mei R.H. Liu F. Shen Physiological property of postharvest sweet sorghum stalk and its modified atmosphere packaging storage Trans. CSAE 24 2008 165 170 Menges and Ertekin, 2006 H. Menges O.C. Ertekin Mathematical modeling of thin layer drying of Golden apples J. Food Eng. 77 2006 119 125 Midilli et al., 2002 A. Midilli H. Kucuk Z. Yapar A new model for single-layer drying Dry Technol. 20 2002 1503 1513 Ning et al., 1995 X.B. Ning Z.H. Ma D. Li Determination of the components in stem juice of sweet sorghum J. Shenyang Agric. Univ. 26 1995 46 48 Ong and Law, 2009 S.P. Ong C.L. Law Mathematical modelling of thin layer drying of salak J. Appl. Sci. 9 2009 3048 3054 Prasad et al., 2007 S. Prasad A. Singh N. Jain H.C. Joshi Ethanol production from sweet sorghum syrup for utilization as automotive fuel in India Energy Fuels 21 2007 2415 2420 Rooney et al., 2007 W.L. Rooney J. Blumenthal B. Bean J.E. Mullet Designing sorghum as a dedicated bioenergy feedstock Biofuel. Bioprod. Biorefin. 1 2007 147 157 Shen and Liu, 2009 F. Shen R. Liu Research on solid-state ethanol fermentation using dry sweet sorghum stalk particles with active dry yeast Energy Fuels 23 2009 519 525 Shen and Liu, 2010 F. Shen R. Liu Storage of sweet sorghum fresh juice with ethyl-p-hydroxybenzoate and the ethanol fermentation with the preserved juice J. Biobased Mater. Bioenergy 4 2010 295 300 Sik et al., 2010 H.S. Sik K.T. Choo S. Zakaria S. Ahmad M. Yusoff C.H. Chia The influence of drying temperature on the hygroscopicity of rubberwood ( Hevea brasiliensis ) J. Agric. Sci. 2 2010 48 58 Sipos et al., 2009 B. Sipos J. Réczey Z. Somorai Z. Kádár D. Dienes K. Réczey Sweet sorghum as feedstock for ethanol production: enzymatic hydrolysis of steam-pretreated bagasse Appl. Biochem. Biotechnol. 153 2009 151 162 Torul and Pehlivan, 2002 T. Torul D. Pehlivan Mathematical modelling of solar drying of apricots in thin layers J. Food Eng. 55 2002 209 216 Vijayaraj et al., 2007 B. Vijayaraj R. Saravanan S. Renganarayanan Studies on thin layer drying of bagasse Int. J. Energy Res. 31 2007 422 437 Wang et al., 2006 H. Wang X. Hu F. Chen J. Wu Z. Zhang X. Liao Z. Wang Kinetic analysis of non-enzymatic browning in carrot juice concentrate during storage Eur. Food Res. Technol. 223 2006 282 289 Wang et al., 2007 Z. Wang J. Sun X. Liao F. Chen G. Zhao J. Wu X. Hu Mathematical modeling on hot air drying of thin layer apple pomace Food Res. Int. 40 2007 39 46 Yaldiz et al., 2001 O. Yaldiz C. Ertekin H.I. Uzun Mathematical modeling of thin layer solar drying of sultana grapes Energy 26 2001 457 465