Abstract:Background: To prevent the absorption and collapse of the labial bone plate of the anterior teeth, immediate implantation and socket shield technique have been increasingly applied to anterior dental aesthetic implant restoration. Objective: To provide a biomechanical basis for implant restoration of maxillary anterior teeth, finite element analysis was used to investigate the stress peak and distribution in different anatomical sites of natural teeth, conventional immediate implantation and socket shield technique. Methods: Three maxillary finite element models were established, including a maxillary incisor as a natural tooth, a conventional immediate implantation and a socket shield technique. A mechanical load of 100 N was applied to simulate and analyze the biomechanical behavior of the root, periodontal ligament (PDL), implant and surrounding bone interface. Results: The stress distribution of the natural tooth was relatively uniform under load. The maximum von Mises stress of the root, periodontal ligament, cortical bone and cancellous bone were 20.14 MPa, 2.473 MPa, 19.48 MPa and 5.068 MPa, respectively. When the conventional immediate implantation was loaded, the stress was mainly concentrated around the neck of implant. Maximum stress on the surface of the implant was 102 MPa, the cortical bone was 16.13 MPa, and the cancellous bone was 18.29 MPa. When the implantation with socket shield technique was loaded, the stress distribution of the implant was similar to that of immediate implantation. Maximum stress on the surface of the implant was 100.5 MPa, the cortical bone was 23.11 MPa, the cancellous bone was 21.66 MPa, the remaining tooth fragment was 29.42 MPa and the periodontal ligament of the tooth fragment was 1.131 MPa. Conclusions: 1. Under static loading, both socket shield technology and conventional immediate implantation can support the esthetic restoration of anterior teeth biomechanically. 2.Under short-term follow-up, both immediate implant and socket shield technology achieved satisfactory clinical results, including bone healing and patient satisfaction. 3.The stress distribution is mainly located on the buccal bone surface of the implant and is associated with resorption of the buccal bone plate after implant replacement in both socket shield technology and conventional immediate implantation. 4.The presence of retained root fragment had an impact on the bone graft gap. In immediate implantation, the peak stress was located in the cortical bone near the implant position, while in socket shield technology, the peak stress was at the neck of the cortical bone corresponding to the retained root fragment.

Comparison of Stress Distribution at Cervical Bone Between Perfect Implant and Replace Implant in Delayed Loading

Three dimensional finite element analysis of biomechanical distribution of dental implants with immediate load and delayed load

Three Dimensional Finite Element Analysis of the Stress Distribution of Dental Implants with Immediate Loading

[Stress Distribution in Press-Fit Orthodontic Microimplant Bone Interface].

[Effects of Alveolar Bone Resorption on Stress of Tooth/implant-Supported Restoration Connected by Precision Attachment].

Biomechanical characteristics of maxillary anterior incisor, conventional immediate implantation and socket shield technique - A finite element analysis and case report

Three-dimensional Finite Element Analysis of Influence of Occlusal Surface Height on Stress Distribution Around Posterior Implant-Supported Single Crown

Cone-beam CT evaluation of alveolar ridge modification subject to immediate implant with immediate loading and delayed loading

Effect of Diameter and Length on Stress Distribution of the Alveolar Crest around Immediate Loading Implants

Influence of thickness of cancellous bone and cortical bone in stress distribution in vicinity of an implant

A comparative study on the stress distribution around dental implants in three arch form models for replacing six implants using finite element analysis

Three-dimensional finite element analysis of the effect of different bone quality on stress distribution in an implant-supported crown

Biomechanical Evaluation of Bone Atrophy and Implant Length in Four Implants Supporting Mandibular Full-Arch-Fixed Dentures

Three-dimensional finite element analysis of stress distribution on short implants with different bone conditions and osseointegration rates

Effect of different biocompatible implant materials on the mechanical stability of dental implants under excessive oblique load

Analysis of stress distribution in ceramic and titanium implants in alveolar sockets of the anterior region of the maxilla

Influence of sagittal root positions on the stress distribution around custom-made root-analogue implants: a three-dimensional finite element analysis

Author Response for "effect of Peri‐implant Bone Resorption on Mechanical Stress in the Implant Body: in Vivo Measured Load‐based Finite Element Analysis"

Optimum Selection of the Dental Implant Diameter and Length in the Posterior Mandible with Poor Bone Quality – A 3D Finite Element Analysis

Alveolar Bone Stress Around Implants With Different Abutment Angulation: An FE-Analysis of Anterior Maxilla

Effect of Short Dental Implant Material on Bone Stress: An In Vitro Finite Element Analysis