Abstract:Three coating materials, namely sodium sulphate, 1.6R and 2.35R sodium silicate, were respectively used to coat sodium percarbonate (SPC) particles in a fluidised bed coater to achieve its delayed release in aqueous environment. The size of SPC particles was measured using image analysis. The thickness and porosity of the shell materials were analysed using scanning electron microscopy (SEM) and helium pycnometry respectively. The rates of SPC release from uncoated and the coated particles were measured using an iodide molybdate titration method coupled with UV-vis spectrometry. The results indicate that sodium sulphate coating with an average thickness of 53 ± 9 μm only reduced the release rate of SPC as no delayed release was observed. In contrast, sodium silicate coating generated a significant delayed release. 1.6R sodium silicate coating with a thickness of 109 ± 8 μm delayed the release of SPC by approximate 60 s under a static condition. At the same condition, 2.35R sodium silicate coating with a thickness of 71 ± 10 μm delayed the release by approximately 7 min. When the coated SPC particles immersed in water were shaken using an orbital shaker at 150 rpm, the delayed time was reduced by 50% in comparison with the static condition. The 1.6R sodium silicate shell in solid phase transformed to gel-like structure during dissolution and the hydrodynamic forces generated in the shaker accelerated its dissolution. However, there was no significant change of 2.35R sodium silicate shell when the capsules were immersed in water under the static condition, and they broke into pieces in the shaker. For both 1.6R and 2.35R sodium silicate, the further increase in shell thickness increased their shell porosity, which facilitated the water penetration and thus resulted in no significant benefit to additional delay. Moreover, the thermal stability of SPC after coating was slightly improved and the flowability did not change significantly. This study demonstrates that a significant delay in release of SPC can be achieved using 2.35R sodium silicate as a coating material.

Preparation of BSA Pellets by Supercritical Carbon Dioxide Fluid and in Vitro Evaluation

Controllable Preparation and Formation Mechanism of BSA Microparticles Using Supercritical Assisted Atomization with an Enhanced Mixer

Preparation of Core-Shell Polycarbonate/BaSO_4 Submicron Composite Particles

Preparation of Sustained Release Capsules by Electrostatic Dry Powder Coating, Using Traditional Dip Coating As Reference

Delayed Sustained Drug Release from Electrostatic Powder Coated Tablets with Ultrafine Polymer Blends

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Preparation of 5-Amino Salicylic Acid(5-Asa) Colon-Specific Targeting Enzyme-Controlled Release Pellets and Its in Vitro Release

Solid Self-Nanoemulsifying Cyclosporine A Pellets Prepared by Fluid-Bed Coating: Stability and Bioavailability Study

Preparation and in vitro release of 5-aminosalicylic acid time-controlled release pellets for colon-specific delivery

Modulation of Protein Release from Biodegradable Core-Shell Structured Fibers Prepared by Coaxial Electrospinning.

Coating of Sodium Percarbonate Particles Using Water Soluble Materials in a Fluidised Bed to Achieve Delayed Release in Aqueous Environment

Study on Enteric Coated Preparation of Nattokinase Using Supercritical CO2 Fluid Technique

Preparation and the release characteristic in vitro of arsenic trioxide albumin nanospheres

Solid Self-Nanoemulsifying Cyclosporin A Pellets Prepared by Fluid-Bed Coating: Preparation, Characterization and in Vitro Redispersibility

Preparation of Delayed Release Pellets Containing Ginkgolides by Aqueous Coating Technique and Quality Evaluation of the Pellets

Preparation of Arsenic Trioxide Albumim Microspheres and Its Release Characteristicsin Vitro

Formulation of enteric-coated pellets containing diclofenac sodium by coating technology

Preparation of Drug-Loaded Composites by Supercritical Carbon Dioxide Impregnation

Preparation of acetaminophen film coated pellets by centrifugal-coating granulation method

Debinding mechanisms in thermoplastic processing of a Ba(0.5)Sr(0.5)Co(0.8)Fe(0.2)O(3-δ)- stearic acid-polystyrene mixture

Solution Combustion Synthesis of Calcium Phosphate Particles for Controlled Release of Bovine Serum Albumin