Abstract:BACKGROUND:Polylactic acid(PLA)surface is hydrophobic and there are no nataral recognition sites,so its application is limited.Many different strategies have been studied such as composition and chemical Drafting,to produce hydrophilic groups.However,these traditional methods are always involved in complex process and many organic reagents,resulting in decrease of biocompatibility.OBJECTIVE:To conduct the surfacr modification of PL.A and improve its hydrophilicity with low temperature plasma treatment.DESIGN:Controlled observation.SETTING:Department of Materials Science and Engineering in Jinan University.MATERIAIS:The experiment was processed from October 2004 to October 2005 at Guangzhou Research Center of Artificial Organs and Materials Engineering(Ministry of Education).The mainly used materials were:Poly-D,L-lactic acid(Mr 2.9×104,Shandong Medical Instrument Institute),N-vinyl-pyrrolidone(NVP,Acros Company,purified before use).METHODS:The materials were treated in the plasma reactor under different conditions(power=150 W,t=3,2,1 minutes;power=30 W,t=10,8,5,3,1 minutes)to choose the optimal condition,and then PLA were grafted with NVP by gas phase polymerization and liquid polymerization,respectively.MAIN OUTCOME MEASURES:THe surface morphology of the films was observed with scanning electron microscopy and atomic force microscopy.The hydrophilicity of native and treated material surfaces was measured using a water contact angle meter.Surface composition was detected with Fourier transform infrared spectrometer.Mass changesmeasurement was applied to characterize the grafting efficiency.RESULTS:Scanning electron microscopy and atomic force microscopy showed that the plasma medified materials possessed coarse surface with pores and notches.Water contact angles decreased obviously from 78°to 50°after grafting,Fourier transform infrared spectrometer showed a new absorption peak at 1 637.19 cm-1,which corresponded to the carbonyl stretch vibration absorption of amide group in poly-N-vinyl-pyrrolidone.After the plasma treatmerlt at low temperature.the mass change ratio of PLA film material was-0.6.CONCLUSION:The plasma treatment and polymerization can improve the hydrophilicity and cause coarsr surface of PLA material,which will be helpful for the cell attachment.

Enhancing the Cytocompatibility of Poly(D,L-lactide) by a Plasma Technique and Coupling Collagen

Improving the Cell Affinity of A Poly(D, L-Lactide) Film Modified by Grafting Collagen Via A Plasma Technique

A Novel Combined Polyphenol-Aldehyde Crosslinking of Collagen Film-Applications in Biomedical Materials.

Investigation of Plasma Treatment and Collagen Immobilization on the Surface of Poly(lactid-glycolide Acid)

Surface Modification and Biocompatibility of Polydimethylsiloxane Elastomer

Treatment of Poly-L-Lactic Acid Surface by Ammonia Plasma to Promote the Osteoblast Compatibility

Surface Modification of Poly(L-Lactic Acid) to Improve Its Cytocompatibility Via Assembly of Polyelectrolytes and Gelatin

LBL Coating of Type I Collagen and Hyaluronic Acid on Aminolyzed PLLA to Enhance the Cell-Material Interaction

Effect of Ammonia Plasma Treatment on the Properties and Cytocompatibility of A Poly(L-Lactic Acid) Film Surface

Layer-by-layer Assembly to Modify Poly(l-Lactic Acid) Surface Toward Improving Its Cytocompatibility to Human Endothelial Cells.

Surface Modification of Poly-L-lactic Acid Films by Electrostatic Self-Assembly to Promote Vascular Smooth Muscle Cells Growth

Surface Modification Of Polyamide 6 Immobilized With Collagen: Characterization And Cytocompatibility

Surface modification of poly-D,L-lactic acid film with plasma graft polymerization

Surface modification of polycaprolactone substrates using collagen-conjugated poly(methacrylic acid) brushes for the regulation of cell proliferation and endothelialisation

Surface Modification of Polylactic Acid by UV-Irradiation and Its Cytocompatibility

Preparation and Characterization of Collagen-Modified Polylactide Microparticles

Biomimetic Surface Modification Of Poly (L-Lactic Acid) With Gelatin And Its Effects On Articular Chondrocytes In Vitro

Surface Modification of Polycaprolactone Membrane Via Aminolysis and Biomacromolecule Immobilization for Promoting Cytocompatibility of Human Endothelial Cells.

Surface Modification of Poly(L-Lactic Acid) by Entrapment of Chitosan and Its Derivatives to Promote Osteoblasts-Like Compatibility

Enhanced Cell Affinity of Poly(l-Lactide) Film by Immobilizing Phosphonized Chitosan

Endothelial Cell Functions in Vitro Cultured on Poly(L-Lactic Acid) Membranes Modified with Different Methods