Abstract:This work was undertaken to investigate the influences of Mg content on the microstructure and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy. The addition of increasing amounts of Mg led to continuous grain refinement of as-cast base alloy accompanied by the increased volume fraction of secondary phases distributed along grain boundaries or interdendritic regions. The tensile test results showed that Mg addition could greatly enhance the mechanical properties of the base alloy after subjected to the solution treatments and artificial ageing. The precipitation behavior and microstructural evolution were also investigated. The addition of Mg would facilitate the nucleation of δ′ (Al 3 Li) phases after quenching. The presence of Mg was observed to lower the growth rate of δ′ and δ′-precipitation-free zones (δ′-PFZs) of the base alloy. Precipitation of θ′ (Al 2 Cu) phase would be almost suppressed, and S′ (Al 2 CuMg) phase was consequently introduced due to Mg additions. The precipitation of S′ phases was encouraged at the expense of T 1 (Al 2 CuLi) phases as the Mg content increased. The increased amount of S′ phases tended to coalesce to form coarse laths distributed in uneven manner for alloys with relatively high Mg content (≥ 1 wt%). No improvements in mechanical properties were observed in alloys with heterogeneous distribution of coarse S′ laths. The optimal Mg addition in cast Al–2Li–2Cu alloy was 0.5 wt%.

Investigation on the mechanical properties and microstructures of Mg-Zn-Al-Cu cast magnesium alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

Investigating the role of Cu, Zr and V on the evolution of microstructure and properties of Al-Si-Mg cast alloys

Study on the effect of enhanced magnesium and copper contents on microstructure and property of Al-Zn-Mg-Cu alloys with high zinc element content during fabrication processes

Microstructures and Mechanical Properties of Hot-extruded Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,1.5) Alloys

Revealing the Substantial Impact of Trace Mg Addition on the Microstructural Configuration of a Cast Al-Li-Cu-Zr Alloy under Various Conditions

Effect of Cu Additions on Microstructure, Mechanical Properties and Hot-Tearing Susceptibility of Mg-6Zn-0.6Zr Alloys

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Microstructure and Properties of Mg-5Al-1.5Ca-0.4Zn Based Alloyby Semi-Solid Isothermal Heat-Treatment-die-pressure-casting Process

Investigation on microstructures and mechanical properties of Mg–6Zn–0.5Ce–xMn (x = 0 and 1) wrought magnesium alloys

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Microstructures and Mechanical Properties of Ultralight Cast Al-3Li-XMg-0.1Zr Alloys

Effect of Zn/Mg Ratio on Microstructure and Properties of Cold Extruded Al-xZn-2.4Mg-0.84Cu-0.2Zr-0.25Ti Aluminum Alloy

Microstructure and mechanical properties of Mg–4Al–4Nd–0.5Zn–0.3Mn alloy

Study on the Microstructure of Mg-4Zn-4Sn-1Mn-xAl As-Cast Alloys

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys