Abstract:Pure copper is widely used in motor windings, heat exchangers and aerospace engines because of its high electrical and thermal conductivity. High-strength laser powder bed fusion (HS-LPBF) not only allows rapid production of components with complex geometry and high spatial resolution, but also offers various advantages such as small focal spot diameter, fine powder, and small layer thickness, providing advantages for forming complex structural parts in fields such as engines and heat exchangers. A single factor single layer experiment was performed by varying the hatch spacing (H), and the range of hatch spacing was determined according to the overlap rate. The degree of influence of process parameters on the relative density of pure copper specimens was analyzed using an orthogonal experiment, and a comparative study of the phase composition, microstructure and mechanical properties of pure copper specimens was carried out by varying the laser power. The characteristics of pure copper formed by HS-LPBF were analyzed. In addition, the effect of heat treatment on the microstructure and mechanical properties of pure copper specimens was investigated, and the fracture morphology of the specimens was observed comparatively. The results show that the HS-LPBF technique can effectively increase the energy density and improve the specific surface area of the powder and the laser absorptivity due to its small focal spot diameter, fine powder and layer thickness, thus reducing the minimum energy required to melt pure copper powder. The optimum process parameters were obtained by orthogonal experiment with a relative density of 98.1 % of the specimen. The highest hardness, ultimate tensile strength and elongation were obtained at a laser power of 260 W with 84 HV, 320 MPa and 17.8 %, respectively. This ultimate tensile strength is 18 % higher than the highest ultimate tensile strength that has been reported so far. In addition, the average grain size of the optimal specimens was 3.6 μm. Mechanical properties such as hardness, tensile strength and elongation of pure copper parts can be significantly improved by precisely controlling the process parameters, in particular laser power and hatch spacing.

Preparation of Nylon 12 Coated Copper Powders for Selective Laser Sintering

Preparation and selective laser sintering of nylon-12 coated metal powders and post processing

Polymer Brush Induced Electroless Copper Plating on PA12 Surface for Tensile Strength Enhancement of Selective Laser Sintering Part

Selective Laser Melting of High Relative Density and High Strength Parts Made of Minor Surface Oxidation Treated Pure Copper Powder

Phase stability and melting behavior of the α and γ phases of nylon 6

Solid‐state shear milling method to prepare PA12/boron nitride thermal conductive composite powders and their selective laser sintering 3D‐printing

Preparation of nickel/PA12 composite particles by defect-induced electroless plating for use in SLS processing

Hybrid of multi‐dimensional fillers for thermally enhanced polyamide 12 composites fabricated by selective laser sintering

Development a Cu-based Metal Powder for Selective Laser Micro Sintering

Comparative study on 3D printing of polyamide 12 by selective laser sintering and multi jet fusion

Experimental investigating and numerical simulations of the thermal behavior and process optimization for selective laser sintering of PA6

A New Facile Method for Preparation of Nylon-6 with High Crystallinity and Special Morphology

Development of PA6/GO microspheres with good processability for SLS 3D printing

A Facile Fabrication of PA12/CNTs Nanocomposites with Enhanced Three-Dimensional Segregated Conductive Networks and Electromagnetic Interference Shielding Property through Selective Laser Sintering

Study on Preparation and Application of Nano-copper Powder for Power Semiconductor Device Packaging

Microstructures and mechanical properties of pure copper manufactured by high-strength laser powder bed fusion

Effect of Polyamide-12 Material Compositions on Mechanical Properties and Surface Morphology of SLS 3D Printed Part

Metal powders of selective laser sintering

Experimental Research on Selective Laser Sintering of Bamboo Flour/Polyamide Hot-Melt Adhensive Blend

Effect of post-heat treatment on the mechanical and surface properties of nylon 12 produced via material extrusion and selective laser sintering processes

Effects of selective laser melting parameters on surface quality and densification behaviours of pure nickel