Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Research on Flowability in Intake Port of Turbocharged Diesel Engine at High Port Pressure Drop

Numerical Simulation of flow characteristics in a new-type multistage nozzle of pressure drop

Three-dimensional Simulation and Optimization of Engine Intake Ports

An Experimental Study on Intake-ports Characteristics of a Four-valve Diesel Engine

Influence of Intake-port Layout on Air Flow around Intake-valve of a Two-valve Diesel Engine

Three-Dimensional Simulation for Helical Intake Port of 4BTAA Diesel Engine

Research on Performance Matching of Intake and Exhaust Ports of Marine Medium Speed Dual Fuel Engine

Research on the Intake Port of a Uniflow Scavenging GDI Opposed-Piston Two-Stroke Engine

Research on Influence of Inlet Pressure on Diesel Engine Performance

Influence of Inlet and Outlet Area Ratio on Intake Port Flow Capacity

The formation mechanisms of flow field in a compound intake ported rotary engine considering apex seal leakage

Effects of different parameters on the flow field of peripheral ported rotary engines

Research on the Integrated Intercooler Intake System of Turbocharged Diesel Engine

Three-Dimensional Computational Fluid Dynamics Modeling of a 6V150 Diesel Engine

Numerical and Experimental Investigation of Exhaust Manifold Configurations of Turbo-Charged Diesel Engines

Analysis of Intake Flow Loss in Pneumatic Engine

Numerical Analysis of Flow Interaction of Turbine System in Two-Stage Turbocharger of Internal Combustion Engine

DESIGN OF INTAKE MANIFOLD AND EXPERIMENTAL STUDY FOR PRESSURE WAVE SUPERCHARGED DIESEL ENGINES

The effect of intake port shape on in-cylinder flow field and turbulence distribution in a high-tumble production engine with endoscope accesses

Three-Dimensional Computational Fluid Dynamics Modeling of the Combustion Process of a MAN L21/31 Marine Diesel Engine

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method