Abstract:Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.

Experimental Study on Corn Stalk and Rootstalk Cutting by Driven Disc

Comparison and Experiment on Cutting and Ditching Capability of Four Driven Disc

Study on the Driven Disc Cutting Mechanism of the No-tillage Planter in the Soil Bin

Design and Experiment on Power Driven Rootstalk Cutting Mechanism of Ridge-till and No-till Corn Planter

Analysis And Experiment On Cutting Performances Of High-Stubble Maize Stalks

EFFECTS OF VARIOUS EDGE-CURVE TYPES AND ROTATIONAL SPEEDS OF DISC BLADES ON BREAKING FORCE AND ENERGY CONSUMPTION IN THE MAIZE STALK CHOPPING PROCESS

Interaction Mechanisms Between Blades and Maize Root–Soil Composites As Affected by Key Factors: an Experimental Analysis

Experimental Study on Cutting and Chopping Corn Straw with Different Moisture Content

Comparison of Soil and Corn Residue Cutting Performance of Different Discs Used for Vertical Tillage

The Design and Experimental Validation of a Biomimetic Stubble-Cutting Device Inspired by a Leaf-Cutting Ant’s Mandibles

Experimental Study on the Performance of Rollers with Reverse Pull Stalker in Corn Plate

<i>Effects of Contra-rotating Basecutters on Cutting Quality</i>

Design and Experiment of Cob-picking and Stalk-chopping United Mechanism

Experimental Study on the Effect of Water Jet Cutting Parameters on Maize Stalks

Optimization of a Whole-Stalk Operating System after Sugarcane Base Cutting

Optimization of cutting position and mode for cabbage harvesting

SUGARCANE CUTTING QUALITY USING CONTRA-ROTATING BASECUTTERS

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

Cutting Characteristics of Sugarcane in Terms of Physical and Chemical Properties

Modeling of Power Consumption of a Rotary Blade Using Indoor Soil-Bin Test Data

Design and Experiment of Straw Cutting and Rubbing Process Device