Abstract:Traditional methods for achieving hierarchical surface structures include highly specified, deterministic approaches to create features to meet design intention. In this study microstructural alteration was undertaken using laser apparatus and secondary texturing was achieved via succeeding electrochemical processes. Electrochemical jet machining (EJM) was performed on mild steel subjected to laser pre-treatment using power densities of 4167 and 5556W/cm2 with pulse durations from 0.3–1.5s. Results show that in combination, laser pre-treatment and EJM can alter the exposed surface textures and chemistries. Here, machined surface roughness (Sa) was shown to increase from approximately 0.45μm for untreated surfaces to approximately 18μm for surfaces subjected to extreme laser pre-treatments. After pre-treatments materials were characterised to appraise microstructural changes, shown to be martensite formation, reinforced by complementary simulation data, and significant increases in observable hardness from approximately 261HV for the as-received material to over 700HV after pre-treatment. The greater hardness was retained after EJM. Exposed martensitic lath structures at machined surfaces are shown to be partially responsible for surface roughness increases. The surfaces were explored with energy dispersive X-ray spectroscopy (EDS) and Raman spectroscopy demonstrating changes in apparent surface chemistry. This analysis revealed increasing oxide formation at the surface of the pre-treated EJM surface, a further contributory factor to surface roughness increases. This new process chain will be of interest to manufacturers seeking to control surface morphology for applications including micro-injection mould/die manufacture. While demonstrated here for steel similar mechanisms are exploitable in other material systems. A new technique has been demonstrated, resulting from the models and processes presented to couple laser and electrolyte jet processing for complex surface preparation.

Surface modification of 316L stainless steel by high current pulsed electron beam

Surface Nanocrystallization Mechanism of Additive Manufactured 316L Stainless Steel Via High-Energy Shot Peening

Microstructure and property modifications in surface layers of a Mg-4Sm-2Al-0.5Mn alloy induced by pulsed electron beam treatments

Temperature Field and Formation of Crater on the Surface Induced by High Curren T Pulsed Electron Beam Bombardment

Simulation on Surface Morphology Evolution of Metal Targets Irradiated by Intense Pulsed Electron Beam

The impact of high current pulses electron beam on the microstructure and surface properties of Sn/Al system

Surface modification of CrFeCoNiMo high entropy alloy induced by high-current pulsed electron beam

Study on the Fabrication Process of 316L Stainless Steel via Electron Beam Selective Melting

Surface Melting and Evaporation of Pure Mg Bombarded by High Current Pulsed Electron Beam

Microstructure and Properties of TiN/TiCN/Al2O3/TiN Coating Enhanced by High-Current Pulsed Electron Beam

Ultrasonic cavitation erosion of 316L steel weld joint in liquid Pb-Bi eutectic alloy at 550°C

A possible thermodynamic mechanism of craters formation on metal surfaces caused by intense pulsed ion beams

Deep Modification of Materials by Thermal Stress Wave Generated by Irradiation of High-Current Pulsed Electron Beams

Surface electropulsing-induced texture evolution in electron beam melted Ti-6Al-4V alloy for biomedical application

Surface Nanocrystallization and Numerical Modeling of 316L Stainless Steel during Ultrasonic Shot Peening Process

High energy laser-shock induced phase transformation and micro-spallation on surface of stainless steels: The effect of stacking fault energy and deformation mechanisms

Electron Beam Selective Melting of 316L Stainless Steel Powder

Microstructure evolution and electroplasticity in Ti64 subjected to electropulsing-assisted laser shock peening

Studies on surface modification of materials by intense pulsed ion beams

A Novel Electropulsing Treatment to Improve the Surface Strength and Repair the Pore of Additively Manufactured Ti-6Al-4V Alloy

Surface modification of mild steel using a combination of laser and electrochemical processes