Research on Slab Photonic Crystal Waveguides

Yidong Huang,Mao, Xiaoyu,Cui, Kaiyu,Lei Cao

DOI: https://doi.org/10.1109/inow.2007.4302876

2007-01-01

Abstract:Coupling characteristics and gain performances of slab photonic crystal waveguides were investigated theoretically. The simulation results are reported in this paper.

What problem does this paper attempt to address?

Passive and active performances of slab photonic crystal waveguides

Yidong Huang,Xiaoyu Mao,Kaiyu Cui,Chao Zhang,Lei Cao,Xuan Tang,Wei Zhang,Jiangde Peng

DOI: https://doi.org/10.1109/INOW.2008.4634425

2008-01-01

Abstract:Two dimensional slab photonic crystal waveguides were designed and fabricated. Full photonic band gap, band gap guided mode, and mini-stop-bands were observed. Passive and active performances were investigated theoretically and experimentally.
Design, Fabrication, and Measurement of Two-Dimensional Photonic Crystal Slab Waveguides

Zhang Chao,Tang Xuan,Mao Xiao-Yu,Cui Kai-Yu,Cao Lei,Huang Yi-Dong,Zhang Wei,Peng Jiang-De

DOI: https://doi.org/10.1088/0256-307x/25/3/047

2008-01-01

Abstract:Two-dimensional photonic crystal slab waveguides on SOI wafer are designed and fabricated. Photonic band gap, band gap guided mode, and index guided mode are observed by measuring the transmission spectra. The experimental results are in good agreement with the theoretical ones.
Coupling of Two-Dimensional Slab Photonic Crystal Micro-Cavities and Waveguides

Qian Chenjiang,Xie Xin,Yang Jingnan,Zhao Yanhui,Tang Jing,Xu Xiulai

DOI: https://doi.org/10.3788/lop54.030001

2017-01-01

Laser & Optoelectronics Progress

Abstract:Photonic crystal is a structure with periodic dielectric constant and it has photonic band gap, in which the electromagnetic wave can not propagate in the structure. Two-dimensional slab photonic crystals can be fabricated by etching periodic air holes on a slab substrate, which has been investigated and applied extensively because of their good control of light propagation. Photonic crystal micro-cavities and waveguides can be achieved by introducing defects in the two-dimensional slab photonic crystal. The coupling of micro-cavities and waveguides can be controlled by adjusting geometric parameters, so as to realize the optical devices based on two-dimensional slab photonic crystals such as optical switching, optical storage and single photon source, etc. Prop erties of the micro-cavities and waveguides of two-dimensional slab photonic crystals are introduced, and their coupling control and potential applications in optical quantum information processing are discussed as well.
Photonic Crystal Waveguides and Their Applications

Yidong Huang,Xiaoyu Mao,Chao Zhang,Lei Cao,Kaiyu Cui,Wei Zhang,Jiangde Peng

DOI: https://doi.org/10.3788/col20080610.0704

2008-01-01

Abstract:Two-dimensional (2D) slab photonic crystal waveguides (PCWGs) on silicon-on-insulator (SOI) wafer were designed and fabricated. Full photonic band gap, band gap guided mode, and index guided mode were observed by measuring the transmission spectra. Mini-stop-bands in the PCWG were simulated with different structure paramaters. Coupling characteristics of PCWG were investigated theoretically considering the imperfections during the fabrication process. It was found that suppressing power reservation effect can realize both short coupling length and high coupling efficiency.
Study on Properties of Silicon Nano-Slab Waveguides

XIAO Si-miao,LI Yu-bo,LI Guang-bo,JIANG Xiao-qing,WANG Ming-hua,YANG Jian-yi

DOI: https://doi.org/10.3969/j.issn.1005-5630.2005.05.021

2005-01-01

Abstract:In this article we analyzed the guiding properties of air-clad silicon dielectric optical waveguides which have the core width of nanometre size based on Maxwell equation and numerical analysis.By programming,we obtained the proportion of power distribution in cladding,core,and substrate;the curve of how the effective refractive index varied with the core width;how group refractive index and group velocities varied with wavelength and the dispersion curve.We compared these properties with micron-sized waveguides,and found that because of the decrease of core width,the mode field leaks out a lot,which enhances the coupling.This is very important to design and fabric nano-sized optical devices.
High Transmitting and Coupling Characteristics of Light at the Surface of A Photonic Crystal with A Triangular Lattice of Air Holes

Jun Zhang,Tianbao Yu,Nianhua Liu,Jianyi Yang,Qinghua Liao,Xiaoqing Jiang

DOI: https://doi.org/10.1364/josab.29.000748

2012-01-01

Abstract:We investigate and simulate the light transmitting and coupling characteristics of surface mode waveguides (SMWs) based on photonic crystals (PhCs) with a triangular lattice of air holes. We demonstrate that surface waves can be efficiently propagated and served as a new kind of high-efficiency single-SMW-based filter with broad bandwidth in the outer space of PhCs. We also explore the highly efficient coupling of hetero-SMWs constructed by cascading different truncated surfaces. The coupling efficiency is insensitive to the interface position. (C) 2012 Optical Society of America
Three-Dimensional Coupled-Wave Theory for the Guided Mode Resonance in Photonic Crystal Slabs: Tm-Like Polarization

Yi Yang,Chao Peng,Yong Liang,Zhengbin Li,Susumu Noda

DOI: https://doi.org/10.1364/ol.39.004498

IF: 3.6

2014-01-01

Optics Letters

Abstract:A general coupled-wave theory is presented for the guided resonance in photonic crystal (PhC) slabs with TM-like polarization. Numerical results based on our model are presented with finite-difference time-domain validations. The proposed analysis facilitates comprehensive understanding of the physics of guided resonance in PhC slabs and provides guidance for its applications.
Exact Step-Coupling Theory for Mode-Coupling Behavior in Geometrical Variation Photonic Crystal Waveguides

E. H. Khoo,A. Q. Liu,X. M. Zhang,E. P. Li,J. Li,D. Pinjala,B. S. Luk'yanchuk

DOI: https://doi.org/10.1103/physrevb.80.035101

IF: 3.7

2009-01-01

Physical Review B

Abstract:In this paper, an exact step-coupling theory is developed to describe the modes coupling behavior and lightwaves propagation for the power exchange between the waveguide modes in geometrical variation photonic crystal waveguide. The exact step-coupling theory provides a general description of the mode-coupling mechanism for light waveguide with geometrical variation with complete set of equations and solutions. The coupling equations of the exact step theory are derived and compared with the scattering matrix method, where simulation results show good agreement with an error of less than 2.2%. Subsequently, the coupling equations are applied to different case studies such as slab tapered waveguide and lossy "turn-on" waveguide. The transmission spectrum and field pattern distribution show that the lossy waveguide has a large radiation loss with an average transmission efficiency of less than 5%. The slab tapered waveguide can have more than 90% transmission efficiency with the convex curvature. The exact step-coupling theory can be applied to a vast range of geometrical variation photonic crystal based waveguides and it has quick and accurate convergence simulation results.
Slab-Modulated Sidewall Bragg Gratings in Silicon-on-Insulator Ridge Waveguides

Guomin Jiang,Ruiyi Chen,Qiang Zhou,Jianyi Yang,Minghua Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1109/LPT.2010.2089613

2011-01-01

Abstract:A slab-modulated sidewall Bragg grating realized by periodically structural corrugation in the sides of silicon slab is demonstrated on a silicon-on-insulator ridge waveguide. Based on this structure, narrow bandwidth can be accurately controlled by varying the distance between the slab grating region and the ridge with high fabrication tolerance. And low side lobes can also be conveniently achieved by changing the extent of sidewall grating teeth. Experimental results show that bandwidths of the example devices can be changed from 0.64 to 1.4 nm, which agree well with the simulated results.
Photonic Crystal Slab And Si-Wire Waveguide Devices

hirohito yamada,tao chu,akiko gomyo,jun ushida,masayuki shirane,satomi ishida,yasuhiko arakawa

DOI: https://doi.org/10.1117/12.690987

2006-01-01

Abstract:We fabricated various microscopic optical devices using photonic crystal slab and Si-wire waveguides and demonstrated their fundamental characteristics. We demonstrated a channel-dropping filter with a photonic crystal slab point-defect optical cavity. Wavelength resolution of less than 1.5 nm and signal dropping efficiency of more than 90 % were obtained for a 20-gm-square device. We also demonstrated an optical add/drop multiplexer with Bragg grating reflectors made from Si-wire waveguides. Its dropping wavelength bandwidth was less than 2 run, and the center wavelength of the dropped optical signal could be tuned by thenno-optic control using a microheater formed on the Bragg reflector. Using Si-wire waveguide, we also demonstrated thermo-optic switches by forming a micro heater on a branch of a Mach-Zehnder interferometer constructed from the waveguides. In this switching operation, we observed an extinction ratio of more than 30 dB, switching power of less than 100 mW, and switching response speed of less than 100 las using a 1 x 2 optical switch with an 85 x 30 mu m(2) footprint. Using the 1 x 2 optical switch elements, we also fabricated a compact 1 x 4 optical switch and demonstrated its fundamental operation.
Arbitrary Polarization Conversion with a Photonic Crystal Slab

Yu Guo,Meng Xiao,Yang Zhou,Shanhui Fan

DOI: https://doi.org/10.1002/adom.201801453

IF: 9

2019-01-01

Advanced Optical Materials

Abstract:It is shown that a simple photonic crystal slab structure provides a powerful mechanism for the control of the polarization properties of light. For a lossless system, for a given incident light with any fixed polarization, one can generate arbitrary polarization in the reflected light, as one varies the direction of the incident light. In the lossy system, the capability for arbitrary polarization generation is still preserved for s‐ or p‐polarized incident light. This capability for arbitrary polarization generation closely relates to the nontrivial topological properties of the reflection matrix of the structure and exists over a wide range of frequencies.
Decoupling of Multiple Coupled Photonic Crystal Waveguides

Tianbao Yu,Nianhua. Liu,Jiehui Huang,Jianyi Yang,Xiaoqing Jiang

DOI: https://doi.org/10.1109/lpt.2009.2013131

IF: 2.6

2009-01-01

IEEE Photonics Technology Letters

Abstract:Decoupling of multiple coupled photonic crystal waveguides (M-CPCWs) is investigated based on the self-imaging principle. We choose the three-, four-, and eight-CPCWs as typical structures to discuss the general characteristics of the M-CPCWs. It is found that around the frequency where the multiple guided modes are almost degenerate, the power transfer in the M-CPCWs is eliminated for any entrance. The frequency region for decoupling is insensitive to the number of coupled waveguides with the extinction ratios higher than -15 dB. The decoupling of the M-CPCWs exhibit many advantages and may have practical applications in photonic integrated circuits.
Modeling and Characterization of Tunable Photonic Crystal Waveguides Based on Two-Dimensional Periodic Arrays of Silicon Pillars

Haider Butt,Qing Dai,Timothy D. Wilkinson,Gehan A. J. Amaratunga

DOI: https://doi.org/10.1117/12.869833

2010-01-01

Abstract:Highly dense two-dimensional periodic arrays of nano-scaled silicon pillars present the capacity for acting as photonic crystals which can mould, manipulate and guide light. We demonstrate finite element modelling of silicon pillars based photonic crystals and their effective use in applications like waveguides, multiplexers and switches. The optical wave propagation through these structures was thoroughly simulated and analysed, confirming their high efficiency.Later the fabrication of highly periodic two-dimensional arrays of silicon pillars through the process of etching is also explained. High quality of fabricated silicon pillars is displayed in various scanning electron microscope images. The arrays with pillar radius of 50 nm and lattice constant of 400 nm were successfully utilised as optical waveguides with sharp turns. The experimental results are presented showing a good match with the simulation band gap results. Finally we also present the concept of utilising liquid crystals as an anisotropic medium around the silicon nano-pillars to establish tuneable photonic crystals waveguides. The cell geometry for such a hybrid device is suggested in which by application of voltage the dielectric constant of liquid crystals can be controlled and essentially the waveguides can be tuned.
Study of the Photonic Crystal Waveguide Based on 2D Compound Lattice Structure

Chao-jun Wu,Yan-ping Li,Zi-yu Wang

DOI: https://doi.org/10.1007/s11801-009-9061-3

2009-01-01

Abstract:By employing 2D plane wave expansion (PWE) and finite difference time domain (FDTD) methods, a photonic crystal waveguide (PCW) based on the compound square lattice structure is presented. Band-gap can be observed for TM polarization and compared with the simple lattice structure based on the same material, the band-gap is increased by 62.7%. By optimizing the parameters we get the PCW with the propagation only near the wavelength of 1.55 µm and a flat group index curve in a wide wavelength range of 40 nm. And the group velocity dispersion compensation can be realized by the structure optimization. The results provide a reference for the study and application of photonic crystal waveguide based on the compound lattice structure.
Analysis to closed surface-wave photonic crystal waveguides based on coupled-resonator optical waveguide theory

Y.H. Zheng,C. Wang,J.C. Cao

2023-10-31

Abstract:Traditionally, one can construct a waveguide by introduce defects into surface-wave photonic crystals (SPCs). Here we propose a new structure named closed SPC that can introduce waveguide modes out of photonic bandgap of surface-wave photonic crystal. In this paper, we have comprehensively analyzed dispersion relation, group velocity, normalized transmission and electric field distribution of closed SPC waveguides, and propose several methods to improve performance of the waveguide based on coupled-resonator optical waveguide theory. These methods can improve transmission efficiency from 10% to 60% and eliminate intraband oscillation by adjusting eigenfrequency and coupling factor . These methods are applicable to both single mode and multi mode situations. This letter also paves a new way for improving the performance of other coupled-resonator waveguides.

Optics
Slab-Thickness Dependence of Photonic Bandgap in Photonic-Crystal Slabs

Jin Hou,David S. Citrin,Huaming Wu,Dingshan Gao,Zhiping Zhou,Shaoping Chen

DOI: https://doi.org/10.1109/jstqe.2011.2169773

IF: 4.9

2011-01-01

IEEE Journal of Selected Topics in Quantum Electronics

Abstract:The slab-thickness dependence of the photonic bandgap in air-bridge photonic-crystal slabs was theoretically investigated by the 3-D plane-wave expansion method. The photonic bandgap was found to achieve a maximum for a certain slab thickness depending on air-hole volume filling factor. A kink in the photonic bandgap width versus slab thicknesses was observed, and found to be due to a transition in the nature of the modes at the top of the bandgap. Through a systematic investigation, a linear relation between the optimized slab thickness for the maximum photonic bandgap versus air-volume filling factor was found to hold over a wide range of air-volume filling factors. The linear relation also holds for photonic-crystal slabs composed of other materials and would favor the design and application of various 2-D photonic-crystal-slab devices such as reflectors, cavities, and waveguides.
P4-6: Single-mode transmission in planar photonic crystal folded waveguide

Qianzhong Xue,Yian L. Li,Chao Hai Du,Zuo Yuan

DOI: https://doi.org/10.1109/IVELEC.2010.5503456

2010-01-01

Abstract:A folded waveguide composed of dielectric photonic crystal material is designed and its in-plan propagation characteristics are studied by calculating the dispersion diagram using finite difference frequency domain algorithm and analyzing the electromagnetic wave guiding by finite difference time domain algorithm. It is shown that a high order single-mode with moderate bandwidth can travel through it at a high efficiency, which is desirable for practical applications
Functional Devices Based on Photonic Crystal Waveguides

Kaiyu Cui,Yidong Huang,Xue Feng,Fang Liu,Wei Zhang

DOI: https://doi.org/10.1364/jsap.2014.20a_c1_1

2014-01-01

Abstract:Photonic crystals have drawn a lot of attention due to their potential in guiding, controlling, and manipulating photons. This paper reports our recent research on the functional devices based on photonic crystal waveguides (PCWs).
Analysis of Leaky Modes of Photonic Crystal Slabs with Deeply Patterned Lattice

Hao Zhang,Heyuan Zhu,Liejia Qian,Dianyuan Fan

DOI: https://doi.org/10.1088/1464-4258/8/5/019

2006-01-01

Journal of Optics A Pure and Applied Optics

Abstract:We demonstrate that leaky modes can be observed in asymmetrical photonic crystal slabs on low-index and high-index substrates. The reflective spectra are studied using the scattering-matrix method, and bands of the leaky modes are obtained via the surface-coupling technique. Caused by the lack of the vertical translational symmetry, the transverse electric (TE)-polarized incidence is reflected into light containing a transverse magnetic (TM) component when the incident plane does not possess mirror symmetry, although the conversion efficiency is weak. This phenomenon, i.e. polarization conversion, is studied in detail.
Multi-channel slow light coupled-resonant waveguides based on photonic crystal with rectangular microcavities

shuai feng,lin gan

DOI: https://doi.org/10.1016/j.optcom.2014.12.040

IF: 2.4

2015-01-01

Optics Communications

Abstract:The light transmission characteristics through the coupled-resonator optical waveguides (CROWs) based on the two-dimensional square-lattice photonic crystal with rectangular microcavities are systematically studied by the finite-difference time-domain method. Owing to the multiple spatial symmetries of the defective modes localized by the rectangular microcavities, the guiding bands can be adjusted by changing the coupling region between the CROW and the traditional W1-typed input and output channels, and their corresponding group velocities can be quite different from each other through the same CROW structure. Through optimizing the coupling regions between the CROW and three output channels, a kind of device with both the abilities of light beam splitting and frequency selection can be obtained, which has potential applications in the future complex all-optical circuits.

Research on Slab Photonic Crystal Waveguides

Passive and active performances of slab photonic crystal waveguides

Design, Fabrication, and Measurement of Two-Dimensional Photonic Crystal Slab Waveguides

Coupling of Two-Dimensional Slab Photonic Crystal Micro-Cavities and Waveguides

Photonic Crystal Waveguides and Their Applications

Study on Properties of Silicon Nano-Slab Waveguides

High Transmitting and Coupling Characteristics of Light at the Surface of A Photonic Crystal with A Triangular Lattice of Air Holes

Three-Dimensional Coupled-Wave Theory for the Guided Mode Resonance in Photonic Crystal Slabs: Tm-Like Polarization

Exact Step-Coupling Theory for Mode-Coupling Behavior in Geometrical Variation Photonic Crystal Waveguides

Slab-Modulated Sidewall Bragg Gratings in Silicon-on-Insulator Ridge Waveguides

Photonic Crystal Slab And Si-Wire Waveguide Devices

Arbitrary Polarization Conversion with a Photonic Crystal Slab

Decoupling of Multiple Coupled Photonic Crystal Waveguides

Modeling and Characterization of Tunable Photonic Crystal Waveguides Based on Two-Dimensional Periodic Arrays of Silicon Pillars

Study of the Photonic Crystal Waveguide Based on 2D Compound Lattice Structure

Analysis to closed surface-wave photonic crystal waveguides based on coupled-resonator optical waveguide theory

Slab-Thickness Dependence of Photonic Bandgap in Photonic-Crystal Slabs

P4-6: Single-mode transmission in planar photonic crystal folded waveguide

Functional Devices Based on Photonic Crystal Waveguides

Analysis of Leaky Modes of Photonic Crystal Slabs with Deeply Patterned Lattice

Multi-channel slow light coupled-resonant waveguides based on photonic crystal with rectangular microcavities