Abstract:The three-dimensional (3D) viscoelastic polymer melt filling process in injection molding has always been regarded as a challenging two-phase flow problem. Numerical investigations concerning it are very limited, especially under the non-isothermal condition. Thus, this article presents a 3D non-isothermal two-phase model to investigate the flow-induced stresses during the viscoelastic fluid filling process. The viscoelastic behavior of polymer melt is predicted by the eXtended Pom-Pom (XPP) model, in which the temperature dependence of polymeric viscosity and relaxation times are described using the Arrhenius equation. The 3D governing equations are solved by a collocated finite volume method. The high resolution revised level set method coupled with a domain extension technique is extended to capture the 3D melt front interface in an irregular cavity. The collocated finite volume method and the revised level set solver are respectively validated using the XPP melts past a cylinder and the single vortex flow. Then the ability of the presented 3D two-phase model is verified by the isothermal Newtonian fluid filling process in a thin rectangular cavity. The numerical results are in good agreement with those reported in literature. Finally, the challenging problem of non-isothermal XPP fluid filling process in a 3D rectangular cavity with one cylindrical insert is investigated. The temperature field, flow-induced stresses and the corresponding rheological behaviors of polymer melt during 3D filling process are quantitatively predicted. Especially, the effects of processing conditions and energy source term on the two normal stress differences are discussed. It is found that melt temperature and injection velocity are the main factors that affect the normal stress differences. The obtained results should be helpful for improving the product properties in practical production. (C) 2016 Elsevier Ltd. All rights reserved.

Characterization of the time-dependent nonlinear viscoelastic of a LDPE melt using a simple thixotropy model

The characterization of the time-dependent nonlinear viscoelastic of an LDPE melt using a simple thixotropy model

The Thixotropy-Loop Behaviors of An LDPE Melt: Experiment and Simple Analysis

The Non-Linear and Time-Dependent Rheological Characteristic for A Ldpe Melt and Its Description

Time-dependent Viscoelastic Behavior of an LDPE Melt

Characterizations on the Thixotropy-Loop Tests Using Ucm Model with A Rate-Type Kinetic Equation

Thixotropy-loop Tests by Using Upper Convected Differential Maxwell-type Model with Kinetic Theory

The prediction on the non-linear and time-dependent rheological characteristics

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Mechanical Behaviors of Copolymer Elastomers: Experimental Characterization and Constitutive Modelling

Viscoelastic Property of an LDPE Melt in Triangular- and Trapezoidal-Loop Shear Experiment

Descriptions on the Thixotropy-Loop Tests by the Simplified Mewis-Denn Model

Evaluate the Nonlinear Viscoelasticity of Polyolefin Melts Using the Larson Model

A New Visco–elasto-Plastic Model Via Time–space Fractional Derivative

Rheological Characterizations and Extrudate Swell Predictions of an LDPE Melt by Two KBKZ-type Constitutive Equations

THE DESCRIPTIONS OF VISCOELASTIC FOR A LDPE MELT BY USING WAGNER EQUATION AND THE PREDICTIONS ON ITS NON-LINEAR AND TIME-DEPENDENT CHARACTERISTIC

A Three-Dimensional Thermal Model for Viscoelastic Polymer Melt Packing Process in Injection Molding

Stress Relaxation Characteristics and Extrudate Swell of the IUPAC-LDPE Melt

PREDICTIONS OF THE THIXOTROPY-LOOP TESTS OF LDPE MELT BY USING THE SIMPLIFIED ACIERNO-TYPE MODEL

Three-dimensional Simulations of Non-Isothermal Transient Flow and Flow-Induced Stresses During the Viscoelastic Fluid Filling Process

A Thermo-Mechanically Coupled Nonlinear Viscoelastic–viscoplastic Cyclic Constitutive Model for Polymeric Materials