Abstract:The effects of varying Mg and Si levels on the microstructural inhomogeneity and eutectic Mg 2 Si morphology in die-cast Al–Mg–Si alloys have been investigated. It was found both Mg and Si additions decreased the microstructural inhomogeneity by producing more well distribution of primary α-Al and Al–Mg 2 Si eutectics, but had contrary effects on eutectic Mg 2 Si morphology. The increasing Mg level transformed eutectic Mg 2 Si from rod or lamellae to curved flake with larger eutectic spacing λ, while the increasing Si level promoted the formation of rod-like or lamellar eutectic Mg 2 Si with smaller λ. The reason for the above evolutions can be traced back to alloys’ solidification behaviour. Thermodynamic calculation indicates that both Mg and Si decrease the liquidus temperature and suppress the precipitation of coarse primary α-Al grains (which tend to agglomerate in centre zone of samples) during the first solidification in shot sleeve, thus reducing the microstructural inhomogeneity. Mg addition shifts the eutectic point to lower Mg 2 Si concentration and induces a slower eutectic growth rate, causing a lower Mg 2 Si volume fraction in Al–Mg 2 Si eutectic cell. On the contrary, Si addition increased the Mg 2 Si volume fraction in eutectic cell by raising the Mg 2 Si eutectic concentration and the eutectic growth rate. To minimize the interfacial energy, Al–Mg 2 Si eutectics with different Mg 2 Si volume fractions exhibit various morphologies. The tensile test results show that both Mg and Si improved the strength at the cost of ductility. However, due to the formation of fine Al–Mg 2 Si eutectics, Si induced less ductility sacrifice than Mg when achieving the same strength improvement.

Dependence of microstructure scales of eutectics on Ca-Si modifier amount in austenite steel composites

Effects of Growth Rate and Amount of Ca–Si Modifier on the Microstructure Scales of Granular Eutectics in an Austenite Medium Mn Steel

Study on granulation mechanisms of γ+(Fe,Mn)3C eutectics in austenite steel composites

Study of the Formation and Intergrowth of Granular Eutectic in Austenitic Steel Matrix Composite by Directional Solidification Technology

Structure and Property Modulations of 13cr Stainless Steel Through Microgravity Solidification and Minor Ce Addition

Structure and properties of in-situ granular γ+(Fe,Mn)3C eutectics reinforce austenite steel matrix composites

Microstructure Control and Micromechanical Property Enhancement of CoCrFeNiZr 0.5 Alloy under Melt Quenching and Electrostatic Levitation Conditions

Effects of Alloying Elements on Solidification Structures and Macrosegregation in Slabs

Micromechanical behavior of eutectoid steel quantified by an analytical model calibrated by in situ synchrotron-based X-ray diffraction

Effect of Ca Addition on Solidification Microstructure of Hypoeutectic Al-Si Casting Alloys

Segregation of C and Mn Elements and Microstructure of in-situ Steel Matrix Composites under Electromagnetic Processing

Comprehensive Microstructure Regularization Mechanism and Microstructure–property Stability at 1773 K of Directionally Solidified Al2O3/GdAlO3 Eutectic Ceramic Composite

Relationships Between Macrostructure and Microstructure in Lamellar Graphite Iron Castings

Effect Of Fe Content On The As-Cast Microstructures Of Ti-6al-4v-Xfe Alloys

Enhancement of mechanical properties by changing microstructure in the eutectoid steel

The Effects of Varying Mg and Si Levels on the Microstructural Inhomogeneity and Eutectic Mg2Si Morphology in Die-Cast Al–Mg–Si Alloys

Effects of Ca addition on the microstructure and tensile properties of Mg-4Al-EE alloy

Microstructure Evolution and Mechanical Properties of Eutectoid Steel with Ultrafine or Fine (ferrite+cementite) Structure

Valence Electron Study on Si Enhancing Dendritic Segregation of C and Mn

Investigation of the Influences of Ternary Mg Addition on the Solidification Microstructure and Mechanical Properties of As-Cast Al–10Si Alloys

Effects of Ca(Y)-Si Modifier on Interface Morphology and Solute Segregation During Directional Solidification of an Austenite Medium Mn Steel