Abstract:Proton exchange membrane fuel cells (PEMFCs) as a promising clean energy conversion technology have gained considerable attention. However, the high cost and low durability of Pt-based nanocatalysts for the cathodic oxygen reduction reaction (ORR) hinder the wide adoption of this technology. 1 Despite great efforts on the development of advanced Pt-based catalysts to improve the Pt utilization and mass activity toward ORR, 2-3 their high activities/durability measured in liquid cells have rarely been realized in fuel cells. On the other hand, carbon-based Pt group metal (PGM)-free ORR electrocatalysts consisting of highly dispersed transition-metal single atoms in nitrogen-coordinated carbon surfaces (Me-N-C) are promising candidates to replace Pt. 4 Unfortunately, the poor durability of Me-N-C has limited their practical applications. 5 Some early studies 6-7 shown that Me-N-C as a support for Pt-based electrocatalyst could improve the stability of the latter. Herein, we report a hybrid electrocatalyst (denoted as Pt-Fe-N-C) consisting of Pt-Fe alloy nanoparticles on highly dispersed Pt and Fe single atoms in a nitrogen-doped carbon support (Figure 1a). The multiple types of active sites result in not only a 3.7 times higher Pt mass activity, but also excellent durability. The performance loss is negligible even after 100,000 potential cycles (Figure 1b), and no current drop is observed at 0.6 V in a fuel cell test with an ultra-low Pt loading (0.015 mg Pt cm −2 ) in the cathode. The morphology and structure of Pt-Fe-N-C catalyst after 100,000 cycles in a fuel cell were further analyzed. Abundant single atoms were still uniformly distributed on the carbon support. No noticeable aggregation of Pt-Fe nanoparticles was observed. Most of particle size was smaller than 4 nm, a solid PtFe@Pt core-shell structure was formed. Around 7% large size particles formed a percolated structure. This work highlights the importance of the synergistic effects among different active sites in hybrid electrocatalysts and provide an alternative way to design more active and durable low-PGM electrocatalysts for fuel cells and other electrochemical devices. This work was supported by the Research Grant Council (HKUST C6011-20G) and Shenzhen Science and Technology Innovation Committee (SGDX2019081623340748). Figure 1. (a) Scanning transmission electron microscope image (the spots in the blue and red dashed circles are ascribed to the Fe and Pt single atoms, respectively). (b) H 2 /O 2 fuel cell polarization (solid symbols and left axis) and power density (hollow symbols and right axis) plots of the Pt-Fe-N-C cathode before cycling (blue) and after 100,000 potential cycles (red) between 0.6 and 0.95 V. Figure 1

Studies on PEMFC Electrocatalysts: Physicochemical Characterization of Homemade Pt/C Electrocatalyst

Study of PEMFC electro-catalysts: Characteristics of a homemade CO-tolerant Pt-Ru/C catalyst

Preparation and Characterization of the Carbon Nano Tubes Supporting Oxygen Electrode Material for PEMFC

Electrocatalytic and Lifetime Studies of Commercial Catalystsin a PEMFC

Preparation and Performance Study of an Unsupported Pt Catalyst for Proton Exchange Membrane Fuel Cell

Research on Electrocatalysts of Proton Exchange Membrane Fuel Cells

Triple-Phase Interfacial Engineering Pt-Ceo2-Nitrogen-Doped Carbon Electrocatalysts for Proton Exchange Membrane Fuel Cells

Study on Platinum and Copper Nanosheets Alloys Supported on Mesoporous Titanium Dioxide Doped with Carbon Black As Electrocatalysts in Pem Fuel Cells

Microwave-assisted synthesis of Pt/CNT nanocomposite electrocatalysts for PEM fuel cells.

Synthesis and characterization of carbon riveted Pt/MWCNTs@TiO 2-TiC catalyst with high durability for PEMFCs application

Platinum-group-metal Catalysts for Proton Exchange Membrane Fuel Cells: from Catalyst Design to Electrode Structure Optimization

Preparation and Characterization of Carbon-supported MnOx-Pt Catalyst for PEMFC

Improving the High-Current-Density Performance of PEMFC Through Much Enhanced Utilization of Platinum Electrocatalysts on Carbon

Actualizing in Situ X-ray Absorption Spectroscopy Characterization of PEMFC-Cycled Pt-Electrodes

Atomically Dispersed Pt and Fe Sites and Pt-Fe Nanoparticles for Durable Proton Exchange Membrane Fuel Cells

Recent Advances in Pt Catalysts and Membrane Electrode Assemblies Fabrication for Proton Exchange Membrane Fuel Cells

Ordered Porous TiO2@C Layer as an Electrocatalyst Support for Improved Stability in PEMFCs

Nanostructured Ultrathin Catalyst Layer Based on Open-Walled Ptco Bimetallic Nanotube Arrays for Proton Exchange Membrane Fuel Cells

Preparation of Oxygen Reduction Catalyst Electrodes by Electrochemical Acidification and Synergistic Electrodeposition

Triple-phase interfacial engineering Pt-CeO 2 -nitrogen-doped carbon electrocatalysts for proton exchange membrane fuel cells

Durable hybrid electrocatalysts for proton exchange membrane fuel cells