Abstract:Solid molecular dispersions of bicalutamide (BL) and polyvinylpyrrolidone (PVP) were prepared by hot melt extrusion technology at drug-to-polymer ratios of 1:10, 2:10, and 3:10 (w/w). The solid-state properties of BL, physical mixtures of BL/PVP, and hot melt extrudates were characterized using differential scanning calorimetry (DSC), powder X-ray diffractometry (PXRD), Raman, and Fourier transform infrared (FTIR) spectroscopy. Drug dissolution studies were subsequently conducted on hot melt extruded solid dispersions and physical mixtures. All hot melt extrudates had a single T(g) between the T(g) of amorphous BL and PVP indicating miscibility of BL with PVP and the formation of solid molecular dispersions. PXRD confirmed the presence of the amorphous form of BL within the extrudates. Conversely, PXRD patterns recorded for physical mixtures showed sharp bands characteristic of crystalline BL, whereas DSC traces had a distinct endotherm at 196 degrees C corresponding to melting of crystalline BL. Further investigations using DSC confirmed solid-state plasticization of PVP by amorphous BL and hence antiplasticization of amorphous BL by PVP. Experimentally observed T(g) values of physical mixtures were shown to be significantly higher than those calculated using the Gordon-Taylor equation suggesting the formation of strong intermolecular interactions between BL and PVP. FTIR and Raman spectroscopy were used to investigate these interactions and strongly suggested the presence of secondary interaction between PVP and BL within the hot melt extrudates. The drug dissolution properties of hot melt extrudates were enhanced significantly in comparison to crystalline BL and physical mixtures. Moreover, the rate and extent of BL release were highly dependent on the amount of PVP present within the extrudate. Storage of the extrudates confirmed the stability of amorphous BL for up to 12 months at 20 degrees C, 40% RH whereas stability was reduced under highly humid conditions (20 degrees C, 65% RH). Interestingly, BL recrystallization after storage under these conditions had no effect on the dissolution properties of the extrudates.

Preparation and Thermodynamics of Moclobemide-Polyvinylpyrrolidone Solid Dispersion

Application of HPMC HME polymer as hot melt extrusion carrier in carbamazepine solid dispersion

Preparation and Physicochemical Characterization of Solid Dispersion of Quercetin and Polyvinylpyrrolidone

Molecular Mechanisms Involved in Supersaturation of Emodin Ternary Solid Dispersions Based on Bonding Agents.

Preparation and Characterization of Solid Dispersions of Dipyridamole with a Carrier “copolyvidonum Plasdone®S-630”

Physicochemical characterization of hot melt extruded bicalutamide-polyvinylpyrrolidone solid dispersions

Facile Preparation of Solid Dispersions by Dissolving Drugs in N-vinyl-2-pyrrolidone and Photopolymerization

Preparation and characterization of the ground mixture of rebamipide commercial tablets and Hydroxypropyl Cellulose-SSL by ball-milling: Application to the dispersoid of mouthwash suspension

Dissolution and absorption researches of curcumin in solid dispersions with the polymers PVP

Preparation and Characterization of Thermo-Sensitive Mixed Micelles and in Vitro Drug Release

Screening of Organic Small Molecule Excipients on Ternary Solid Dispersions Based on Miscibility and Hydrogen Bonding Analysis: Experiments and Molecular Simulation

Preparation, Characterization and in Vitro Evaluation of Solid Dispersions Containing Docetaxel

Effect of composition in the development of carbamazepine hot-melt extruded solid dispersions by application of mixture experimental design

Influence of Solvent Evaporation Rate and Formulation Factors on Solid Dispersion Physical Stability

Creating Drug Solubilization Compartments via Phase Separation in Multicomponent Buccal Patches Prepared by Direct Hot Melt Extrusion-Injection Molding

Study on the Effect of Polymer Excipients on the Dispersibility, Interaction, Solubility, and Scavenging Reactive Oxygen Species of Myricetin Solid Dispersion: Experiment and Molecular Simulation

Stability of Poly(N,N '-Methylenebisacrylamide-co-4-vinylpyridine) Microgel Dispersion and Adjustment of the Hydrophobicity in the Microgels

Preparation of Hot-Melt-Extruded Solid Dispersion Based on Pre-Formulation Strategies and Its Enhanced Therapeutic Efficacy

Physical Characterization of Meloxicam-Β-cyclodextrin Inclusion Complex Pellets Prepared by a Fluid-Bed Coating Method

Establishment of new preparation method for solid dispersion formulation of tacrolimus

Studies on Preparation and in vitro Evaluation of Tacrolimus Solid Dispersions