Carbon Nanotubes Grown on Sepiolite As Catalyst Carrier

JP Cheng,JP Tu,Y Ye,YL Sun,F Liu,YS Ning,FZ Kong,HM Lu,XB Zhang

2002-01-01

Abstract:Multi-walled carbon nanotubes were synthesized by the catalytic decomposition of acetylene at 750degreesC over scpiolite powder, which was treated with aqueous cobalt nitrate. It is expected that the composite with high specific area will have high capacity of hydrogen storage.

What problem does this paper attempt to address?

Methane Catalytic Cracking to Make Hydrogen and Graphitic Nano Carbons (nanotubes, Microfibers, Microballs, Onions) with Zero Emission

Weike Zhang,Lizhen Gao,Min Zhang,Jiali Cui,Yuzhen Li,Lili Gao,Sanyuan Zhang

DOI: https://doi.org/10.1080/15533174.2013.797452

2014-01-01

Synthesis and Reactivity in Inorganic Metal-Organic and Nano-Metal Chemistry

Abstract:Methane was catalytically decomposed to hydrogen and highly graphitic carbon nanotubes, microfibers, microballs, and nano onions. Over Mo (x) -Ni(Fe,Co) (y) -MgO (z) , single-walled carbon nanotubes (SWNTs) and thin-walled carbon nanotubes (TWNTs) were produced; over Ni/Y, individually separated SWNTs were generated; over La2NiO4, multiwalled carbon nanotubes (MWNTs) were made. Over Ni/MCM-41, with the addition of benzene, the carbon microballs (CMBs) were produced. Over Fe-Cr alloy and LaNi0.9Co0.1O3, the carbon nano onions (CNOs) and carbon microfibers (CMFs) were produced, respectively. The methane conversion efficiency and carbon growth rate followed the order: CNOs > CMBs > CMFs > MWNTs > TWNTs > SWNTs.
Synthesis of High Quality Single-Walled Carbon Nanotubes on Natural Sepiolite and Their Use for Phenol Absorption

Jing-Qi Nie,Qiang Zhang,Meng-Qiang Zhao,Jia-Qi Huang,Qian Wen,Yu Cui,Wei-Zhong Qian,Fei Wei

DOI: https://doi.org/10.1016/j.carbon.2010.12.039

IF: 10.9

2011-01-01

Carbon

Abstract:Natural sepiolite mineral was used as a catalyst and catalyst support for the efficient growth of single-walled carbon nanotubes (SWCNTs). With the introduction of hydrogen, uniform active metal nanoparticles can be formed in the fibrous structure of sepiolite ore. High-quality SWCNTs with few defects and a large aspect ratio (over 104) were synthesized. The structure of the CNTs was modified by controlling the catalyst composition with ion-exchange method and changing the growth conditions. The 1 wt.% Fe-based catalyst exhibited excellent activity for the growth of SWCNTs, while the Co/Mo-based catalyst preferred to grow small diameter SWCNTs. The reaction temperature showed a sensitive selectivity to the chirality and diameter distribution of the SWCNTs produced. Catalysts based on the sepiolite can also afford the effective growth of SWCNTs in a fluidized bed reactor. As-grown SWCNTs/calcined-sepiolite demonstrated excellent ability of phenol adsorption, with an adsorption capacity of 155.8mg/g, which was much higher than that on natural sepiolite (12.7mg/g).
Synthesis Of Carbon Nanotubes By Catalytic Decomposition Of Methane Using Lani5 Hydrogen Storage Alloy As A Catalyst

X.P. Gao,X. Qin,F. Wu,H. Liu,Y. Lan,S.S. Fan,H.T. Yuan,D.Y. Song,P.W. Shen

DOI: https://doi.org/10.1016/S0009-2614(00)00784-3

IF: 2.719

2000-01-01

Chemical Physics Letters

Abstract:Carbon nanotubes were synthesized by catalytic decomposition of methane using a hydrogen storage alloy of LaNi5 with a CaCu5 type of hexagonal structure as a catalyst. It was found that surface treatment of LaNi5 alloy particle in KOH solution was effective for providing catalytic sites for carbon nanotube growth. The reaction gas of methane could easily penetrate and reach the catalytic sites on metallic nickel through the decomposed loose surface layer of La2O3. The metallic nickel on the surface layer of LaNi5 alloy particle was dominant for growth of carbon nanotubes. The composite of carbon nanotubes with hydrogen storage alloy would be expected to have a potential application in the field of hydrogen energy. (C) 2000 Elsevier Science B.V. All rights reserved.
Synthesis of carbon nanotubes with Ni/CNTs catalyst

Chunhua Li,Kefu Yao,Dianbo Ruan,Ji Liang,Cailu Xu,Dehai Wu

DOI: https://doi.org/10.1360/03ye9033

2003-01-01

Abstract:Carbon nanotubes (CNTs), owing to their large specific area, good chemical stability and modifiable surface properties after acidic or basic treatment, can be used as catalytic support materials. In this paper, the activities and selectivities of two catalysts, i. e. Ni catalyst supported by carbon nanotubes (Ni/CNTs) and that supported by diatomite (Ni/SiO 2 ), are compared. It is found that the quality of the carbon nanotubes synthesized by the two catalysts is similar, but the yield of the former is 1.5 times higher than that of the latter. The excellent performance of the Ni/CNTs catalyst should be ascribed to the larger specific surface area and proper pore distribution and the structure of the carbon nanotube support.
In Situ Synthesis of Multiwalled Carbon Nanotubes over Lanio3 As Support of Cobalt Nanoclusters Catalyst for Catalytic Applications

Dongyan Xu,Peng Lu,Ping Dai,Haizhen Wang,Shengfu Ji

DOI: https://doi.org/10.1021/jp211009g

2012-01-01

Abstract:In situ synthesis of multiwalled carbon nanotubes (MWCNTs) was performed by chemical vapor deposition of methane on a LaNiO3 perovskite-type growth-promoter prepared by the sol–gel method. The as-produced MWCNTs were purified via a two-step procedure consisting of an oxidation in air and subsequent HNO3 treatment. Nearly monodisperse cobalt nanoparticles with an average size of 11.3 nm have been successfully decorated on MWCNTs by an impregnation–reduction method. The properties of the as-produced carbon nanotubes (CNTs) and Co/CNT catalysts were analyzed by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). It was found that the reduction of LaNiO3 and formation of CNTs occur almost simultaneously under methane atmosphere and that the in situ controlled synthesis of MWCNTs with relatively high purity and uniform diameters could be realized by the chemical vapor ...
Hydrogen Uptake by Carbon Nanotubes

XB Wu,P Chen,J Lin,KL Tan

DOI: https://doi.org/10.1016/s0360-3199(99)00037-3

IF: 7.2

2000-01-01

International Journal of Hydrogen Energy

Abstract:Multi-wall carbon nanotubes were synthesised from the catalytic decomposition of CO and CH4 on powder Co/La2O3 catalysts. TEM and HR-TEM, XRD, and TGA were used to characterise carbon nanotubes. It was found that by adjusting the composition of the catalysts, the size of the nanotubes was controllable and by annealing, the crystallinity could be improved. The carbon nanotubes produced from CO were found to be able to uptake a certain amount of hydrogen under ambient conditions, whereas graphite powders were unable, which suggests that the carbon nanotubes may be a promising material that can be used for hydrogen storage under ambient conditions.
CARBON NANOTUBES GROWING OVER NATURAL MINERALS AND PRELIMINARY STUDY ON THEIR CAPABILITY OF HYDROGEN STORAGE

程继鹏,张孝彬,刘芙,叶瑛,涂江平,孙沿林,陈长聘

DOI: https://doi.org/10.3321/j.issn:0254-0096.2002.06.014

2002-01-01

Abstract:Multi-walled carbon nanotubes (MWCNTs) were synthesized by the catalytic decomposition of acetylene at 750°C under atmosphere of nitrogen over powder of manganese nodules directly and palygorskite powder treated with aqueous cobalt nitrate. The absorbing hydrogen capacity of the new type materials combined MWCNTs with minerals was measured and it might be affected by microstructure and content of elongate particle shape mineral through experiment under moderate pressure at room temperatures. Improving the content of bar-shape palygorskite and keeping structure stability of manganese nodules would improve the hydrogen storage capacity. The speed of hydrogen adsorption would be accelerated through pretreatment of specimen at high temperature in the helium, however the pretreatment has somewhat negative effect on its capacity of hydrogen storage.
Mechanism of carbon nanotube growth in expanded graphite via catalytic pyrolysis reaction using carbores P as a carbon source

Yilong Wang,Wenli Zhang,Yuejun Chen,Xiongfeng Zeng,Jiankun Huang,Hengyong Wei,Junbo Tu

DOI: https://doi.org/10.3389/fchem.2023.1260099

IF: 5.5

2023-10-19

Frontiers in Chemistry

Abstract:Carbon nanotubes (CNTs) had potential applications in energy conversion and storage devices, and it could be prepared by expanded graphite loaded with catalyst at high temperature, however, the mechanism of carbon nanotube growth in expanded graphite need further confirmation. In this work, carbon nanotubes' in situ growth in expanded graphite (EG) were prepared via catalytic pyrolysis reaction using carbores P as a carbon source and Co(NO 3 ) 3 •6H 2 O as a catalyst. The results of X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectroscope (EDS) indicated the carbon nanotubes could generate in, EG with the presence of carbores P as a carbon source and cobalt nitrate as a catalyst. More interestingly, the growth mechanism of carbon nanotubes could be concluded by the results of differential thermal analysis-thermogravimetry-mass spectrometry (DTA-TG-MS) and X-ray photoelectron spectroscopy (XPS) analysis. The pyrolysis products of carbores P were mainly hydrocarbon gas such as CH 4 gas, which reacts with Co(NO 3 ) 3 ·6H 2 O catalyst to reduces CoO x to Co particles, then the carbon form pyrolysis was deposited the on the surface catalyst Co particles and, after continuous solid dissolution and precipitation, carbon nanotubes were at last generated in EG at last.

chemistry, multidisciplinary
Carburization of Fe/Ni Catalyst for Efficient Growth of Single-Walled Carbon Nanotubes

Dewu Lin,Shuchen Zhang,Weiming Liu,Yue Yu,Jin Zhang

DOI: https://doi.org/10.1002/smll.201902240

IF: 13.3

2019-01-01

Small

Abstract:Scale-up production of single-walled carbon nanotubes (SWNTs) with high quality and purity is in pursuit, since the subsequent post purification treatment of residual metal or amorphous carbon is complicated and restricts further applications. Here, a compatible method to efficiently synthesize pure SWNTs on various supporters by using the precarburized Fe/Ni catalysts is reported. The preparation of catalysts is achieved by gas phase deposition together with CO gas at proper temperature, and the carburization of metal particles occurring simultaneously contributes to the size limitation of catalysts. By using micro-quartz sand as a recyclable supporter, high-quality SWNTs with a yield of 50 mg h-1 are prepared with 60% metal precursor utilization, 81% carbon source utilization, and only 0.12% (m/m) metal residues. Taking advantage of carburized Fe/Ni catalysts and appropriate supports makes it possible to balance the quantity, purity, and quality among SWNTs growth. Furthermore, this method provides a straightforward pathway to strongly combine SWNTs and diverse composite materials for further potential applications.
Synthesis of mesoporous carbon nanotubes and their application in gas phase benzene hydrogenation

Dong Cheng Han,Zhi Qing Zhu,Ai Min Zhang,Jian Zhong Zhu,Jia lu Dong

DOI: https://doi.org/10.1016/S0167-2991(03)80477-9

2003-01-01

Abstract:The multi-wall carbon nanotubes with pore diameter of 30-50 nm, synthesized by chemical vapor deposition over Co-La catalyst via decomposition of acetylene at 700 degreesC, were employed as carrier of Ni-loading catalysts and exhibited excellent conversion of benzene and selectivity for cyclohexane in the gas phase benzene hydrogenation under atmospheric pressure.
One-Pot Pyrolysis Method to Fabricate Carbon Nanotube Supported Ni Single-Atom Catalysts with Ultrahigh Loading

Shiyong Zhao,Yi Cheng,Jean-Pierre Veder,Bernt Johannessen,Martin Saunders,Lianji Zhang,Chang Liu,Matthew F. Chisholm,Roland De Marco,Jian Liu,Shi-Ze Yang,San Ping Jiang

DOI: https://doi.org/10.1021/acsaem.8b00903

IF: 6.4

2018-01-01

ACS Applied Energy Materials

Abstract:The practical application of single atom catalysts (SACs) is constrained by the low achievable loading of single metal atoms. Here, nickel SACs stabilized on a nitrogen-doped carbon nanotube structure (NiSA-N-CNT) with ultrahigh Ni atomic loading up to 20.3 wt % have been successfully synthesized using a new one-pot pyrolysis method employing Ni acetylacetonate (Ni(acac)2) and dicyandiamide (DCD) as precursors. The yield and formation of NiSA-N-CNT depends strongly on the Ni(acac)2/DCD ratio and annealing temperature. Pyrolysis at 350 and 650 C led to the formation of Ni single atom dispersed melem and graphitic carbon nitride (Ni-melem and Ni-g-C3N4). Transition from a stacked and layered Ni-g-C3N4 structure to a bamboo-shaped tubular NiSA-N-CNT structure most likely occurs via a solid-to-solid curling or rolling-up mechanism, thermally activated at temperatures of 700-900 degrees C. Extended X-ray absorption fine structure (EXAFS) experiments and simulations show that Ni single atoms are stabilized in the N-CNT structure through nitrogen coordination, forming a structure with four nearest N coordination shell surrounded by two carbon shells, Ni N4. The NiSA-N-CNT catalysts show an excellent activity and selectivity for the electrochemical reduction of CO2, achieving a turnover frequency continued.(TOF) of 11.7 s(-1) at -0.55 V (vs RHE), but a low activity for the O-2 reduction and O-2 evolution reactions, as compared to Ni nanoparticles supported on N-CNTs.
Synthesis,Characterization and Performance of Helical Carbon Nanotubes

Zhang Yang,Fan Meng,Wen Jianfeng,Tang Nujiang,Zhong Wei,Du Youwei

DOI: https://doi.org/10.3969/j.issn.1671-4776.2011.08.003

2011-01-01

Abstract:The Ni nano-particles were generated by means of a sol-gel combined hydrogen reduction method.The helical carbon nanotubes(HCNTs) with high helicity and symmetric structure were synthesized in acetylene pyrolysis at 425 ℃ using the Ni nano-particles as the catalyst.The results show that this method is simple and environmentally friendly with low-cost,and is an ideal candidate for the mass production of HCNTs with high purity.The field-emission scanning electron microscope(FE-SEM) and high-resolution transmission electron microscope(HR-TEM) images show that there are often two nanotubes with the hollow tubular structure and opposite rotating directions in one catalyst nanoparticle.The XRD and Raman results reveal that the composites of the as-prepared sample are graphite with defect and polycrystalline Ni without impurity phase.Moreover,the magnetism and microwave absorption properties of the as-prepared sample were investigated.
Iron Oxide Nanoparticle Impregnated Mesoporous Silicas As Platforms for the Growth of Carbon Nanotubes

D. Barreca,W. J. Blau,G. M. Croke,F. A. Deeney,F. C. Dillon,J. D. Holmes,C. Kufazvinei,M. A. Morris,T. R. Spalding,E. Tondello

DOI: https://doi.org/10.1016/j.micromeso.2007.01.041

IF: 5.876

2007-01-01

Microporous and Mesoporous Materials

Abstract:Iron oxide nanoparticles have been deposited on the exterior of and inside the pores of hexagonal mesoporous silica by a direct synthesis technique with iron phthalocyanine as precursor. Iron loadings were between 0.4wt.% – 3.2wt.%. XPS and Mössbauer spectroscopic studies showed that the initial form of the iron oxide nanoparticles was [Fe2O3]. Samples of these iron-loaded materials were stirred in nitric acid to remove the iron oxide existing on the exterior surface of the silica. No significant loss in mesophase ordering was seen in the TEM, PXRD or nitrogen physisorption analysis of the acid washed samples. Both as-prepared and acid-washed silicas were used to grow multi-walled carbon nanotubes (MWCNTs) from acetylene feedstock in a catalytic chemical vapour deposition reactor at 800°C. In both systems the density of the carbon nanotubes (CNTs) was found to increase with increasing metal loadings. Whereas the as-prepared samples produced CNTs with a range of diameters from 10nm to 90nm, the acid treated samples showed CNTs with much more uniform diameters between 5nm – 15nm. Raman spectroscopy of the products showed that the carbon nanotubes were highly graphitised and of good quality.
Synthesis of Ni and Ni–Cu Supported on Carbon Nanotubes for Hydrogen and Carbon Production by Catalytic Decomposition of Methane

Yi Shen,Aik Chong Lua

DOI: https://doi.org/10.1016/j.apcatb.2014.08.038

2014-01-01

Abstract:Nickel and nickel-copper alloy supported on carbon nanotubes (CNTs) were examined as catalysts for hydrogen production by methane decomposition. The Ni/CNT and Ni-Cu/CNT catalysts were characterized using field emission scanning electron microscopy, energy dispersive X-ray microscopy, transmission electron microscopy and X-ray diffraction. The performance of the catalysts was dependent on the catalyst composition and reaction temperature. The Ni78Cu22/CNT catalyst exhibited the excellent catalytic performance with a stable methane conversion of 0.8 at 700 degrees C, a carbon yield rate of 0.08 gC/(min gNi) at 743 degrees C and a carbon yield of 602 gC/gNi at 700 degrees C. Carbon materials with various morphologies, i.e., herringbone carbon nanofibers (CNFs), platelet CNFs, bamboo-shaped CNFs, branched CNFs, multi-branched CNFs and onion-like carbons, depending on the catalyst composition and reaction temperature, were obtained. The morphology of the produced carbon material was correlated with the growth mechanism of the carbon material on the catalyst. (C) 2014 Elsevier B.V. All rights reserved.
Growth of Carbon Nanotubes with Metal-Loading Mesoporous Molecular Sieves Catalysts

Y Yang,Z Hu,YN Lu,Y Chen

DOI: https://doi.org/10.1016/s0254-0584(03)00282-7

IF: 4.778

2003-01-01

Materials Chemistry and Physics

Abstract:Chemical vapor deposition (CVD) was employed to catalytically synthesize carbon nanotubes (CNTs) with Fe- or Fe/Co-loading M41S (MCM-41 or MCM-48) as catalysts and benzene as precursor at 650°C. The experimental results indicated that the frameworks of the M41S host materials did not collapse after the synthesis process and well-graphitized curved CNTs ranging from 10 to 45nm in diameter could be formed out of the pores of the M41S materials. The maximum yield of CNTs per hour was greater than 200% the weight of the catalyst. Quite a few helix-shaped CNTs were obtained with the structures clearly demonstrated by high-resolution electron microscopy. The good thermal stability and high productivity observed in this study suggested that the mesoporous molecular sieves could be a kind of promising supports for catalytically synthesizing CNTs.
Carbon Nanotube Synthesis and Parametric Study Using CaCO3 Nanocrystals As Catalyst Support by CVD

JP Cheng,XB Zhang,ZQ Luo,F Liu,Y Ye,WZ Yin,W Liu,YX Han

DOI: https://doi.org/10.1016/j.matchemphys.2005.04.043

IF: 4.778

2005-01-01

Materials Chemistry and Physics

Abstract:The preparation of multi-walled carbon nanotubes (MWCNTs) by chemical vapor deposition (CVD) method using nanocrystalline CaCO3 as metal catalyst support was investigated, where acetylene was used as carbon source, and Co, Fe and Ni, as well as their bimetallic compounds as the active component of the catalyst. The smaller size of the CaCO3 support led to a much higher yield of CNTs than previously reported. It was noteworthy that the best performance was Fe-Co nanoparticles, which gave a high yield of CNTs, as judged by experimental results. Growth temperature affected catalytic activity and the disintegration of the support. The raw product was purified to a high level, with little damage on the CNT structure, as confirmed by thermal gravimetric (TG), micro-Raman and transmission electron microscopy (TEM) analyses.
Controllable Synthesis of CNTs Using Pd Catalyst

Xinyong Tao,Xiaobin Zhang,JunLian Wang,Jipeng Cheng,Fu Liu,Junhang Luo,Zhiqiang Luo

DOI: https://doi.org/10.1109/NEMS.2006.334840

2006-01-01

Abstract:High yields of multi-walled carbon nanotubes are synthesized by chemical vapor deposition of acetylene on palladium nanoparticles supported on porous SiO2. HRTEM results reveal that the carbon nanotubes have novel conical inner structure. By changing the content of palladium in the catalyst, we obtained palladium nanoparticles with different diameter distribution. It was found that the apex angles of cones, the outer diameter and the length have a dependence on the diameter of the palladium nanoparticles. Due to the presence of open graphite layers, these novel carbon nanotubes have fascinating potential for energy storage, filed emission and composites
In-situ Growth of Carbon Nanotubes on Ni/NiO Nanofibers As Efficient Hydrogen Evolution Reaction Catalysts in Alkaline Media

Lijun Yang,Xiaochong Zhao,Ruizhu Yang,Pengxiang Zhao,Yintao Li,Pan Yang,Jingchuan Wang,Didier Astruc

DOI: https://doi.org/10.1016/j.apsusc.2019.06.160

IF: 6.7

2019-01-01

Applied Surface Science

Abstract:A novel hierarchical structure of carbon nanotubes grown on Ni/NiO composite nanofiber has been in-situ fabricated by electrospinning and following low-temperature (500 degrees C) vacuum thermal treatment. During vacuum thermal treatment, decomposition of electrospun nickel acetate/polyvinylpolypyrrolidone precursor nanofibers generate gases as a function of both reducing agents and carbon sources for NiO reduction and carbon nanotubes growth. The thermal treatment processing parameter, i.e. heating rate, controls the morphology and composition of the resulting Ni nanofibers or Ni/NiO-carbon nanotubes composite nanofibers. This proposed method avoid the usual extra introduction of reducing agents and carbon source. It is a low cost, high yield and safe no-hazard technique. Then, these non-noble metal-based nanofibers are applied as efficient electrocatalysts for the hydrogen evolution reaction in alkaline solution. The Ni/NiO-carbon nanotubes (10 degrees C min(-1)) can drive 10 mA cm(-2) at an overpotential of 98 mV in 1 M KOH, which is 52 mV less than for Ni nanofibers. This work offers promising novel catalyst materials in water-splitting devices for large-scale production of hydrogen fuel.
Large-Scale and Solvent-Free Synthesis of Magnetic Bamboo-Like Nitrogen-Doped Carbon Nanotubes with Nickel Active Sites for Photothermal-Driven CO 2 Fixation

Yingchun Guo,Xinxin Wang,Lei Feng,Feng Liu,Jinsheng Liang,Xiaomei Wang,Xu Zhang

DOI: https://doi.org/10.1039/d2gc04701b

IF: 9.8

2023-04-05

Green Chemistry

Abstract:The development of a method for the large-scale and solvent-free preparation of hierarchical pore single-atom catalysts is highly desirable but challenging. Herein we report the fabrication of bamboo-like nitrogen-doped carbon nanotubes comprising both Ni single atoms and Ni nanoparticles (Ni-SAs/NPs@BNCNTs) via combining the ball milling and pyrolysis methods. Due to the nature of the carbonaceous species and the plasmonic excitation of the Ni nanoparticles, the as-obtained Ni-SAs/NPs@BNCNTs exhibits excellent photothermal performance, with the reaction solution temperature rising to 70.4 oC at a light intensity of 200 mW/cm2. Semiconductor properties of nickel/nitrogen-doped carbon (Ni-N-C) facilitate the generation of photogenerated electron-hole pairs. Remarkably, the Ni-NPs/SAs@BNCNTs act as a photothermal catalyst for the N-formylation of amines with CO 2 and phenylsilane and exhibits prominent catalytic performance (yield: 95% and selectivity: 96%). This study provides unique insights into the facile and scalable preparation of single-atom catalysts and their photothermal catalytic applications on CO 2 fixation.

chemistry, multidisciplinary,green & sustainable science & technology
In Situ Catalytic Growth of Carbon Nanotubes on the Surface of Carbon Cloth

Qiao-Juan Gong,He-Jun Li,Xiang Wang,Qian-Gang Fu,Zhao-Wei Wang,Ke-Zhi Li

DOI: https://doi.org/10.1016/j.compscitech.2007.05.002

IF: 9.1

2007-01-01

Composites Science and Technology

Abstract:Carbon nanotubes (CNTs) grown on the carbon fiber/matrix interface can improve the interface bonding and accordingly increase the mechanical properties of carbon/carbon composites. Here we report the investigation of preparing CNTs by pyrolizing natural gas on carbon cloth using Ni powder (∼74μm) and sulphur as catalysts. Multi-walled CNTs with 70–100nm in diameter were obtained at 1050–1200°C in a CVD system with flowing Ar. The as-obtained CNTs were of a good crystallinity and high purity, characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy (Raman). In situ catalytic growth mechanism was discussed.

Carbon Nanotubes Grown on Sepiolite As Catalyst Carrier

Methane Catalytic Cracking to Make Hydrogen and Graphitic Nano Carbons (nanotubes, Microfibers, Microballs, Onions) with Zero Emission

Synthesis of High Quality Single-Walled Carbon Nanotubes on Natural Sepiolite and Their Use for Phenol Absorption

Synthesis Of Carbon Nanotubes By Catalytic Decomposition Of Methane Using Lani5 Hydrogen Storage Alloy As A Catalyst

Synthesis of carbon nanotubes with Ni/CNTs catalyst

In Situ Synthesis of Multiwalled Carbon Nanotubes over Lanio3 As Support of Cobalt Nanoclusters Catalyst for Catalytic Applications

Hydrogen Uptake by Carbon Nanotubes

CARBON NANOTUBES GROWING OVER NATURAL MINERALS AND PRELIMINARY STUDY ON THEIR CAPABILITY OF HYDROGEN STORAGE

Mechanism of carbon nanotube growth in expanded graphite via catalytic pyrolysis reaction using carbores P as a carbon source

Carburization of Fe/Ni Catalyst for Efficient Growth of Single-Walled Carbon Nanotubes

Synthesis of mesoporous carbon nanotubes and their application in gas phase benzene hydrogenation

One-Pot Pyrolysis Method to Fabricate Carbon Nanotube Supported Ni Single-Atom Catalysts with Ultrahigh Loading

Synthesis,Characterization and Performance of Helical Carbon Nanotubes

Iron Oxide Nanoparticle Impregnated Mesoporous Silicas As Platforms for the Growth of Carbon Nanotubes

Synthesis of Ni and Ni–Cu Supported on Carbon Nanotubes for Hydrogen and Carbon Production by Catalytic Decomposition of Methane

Growth of Carbon Nanotubes with Metal-Loading Mesoporous Molecular Sieves Catalysts

Carbon Nanotube Synthesis and Parametric Study Using CaCO3 Nanocrystals As Catalyst Support by CVD

Controllable Synthesis of CNTs Using Pd Catalyst

In-situ Growth of Carbon Nanotubes on Ni/NiO Nanofibers As Efficient Hydrogen Evolution Reaction Catalysts in Alkaline Media

Large-Scale and Solvent-Free Synthesis of Magnetic Bamboo-Like Nitrogen-Doped Carbon Nanotubes with Nickel Active Sites for Photothermal-Driven CO 2 Fixation

In Situ Catalytic Growth of Carbon Nanotubes on the Surface of Carbon Cloth