Abstract:Nickel-copper-zinc (NiCuZn) ferrites with high permeability and low magnetic loss have high application potential in high-frequency electronics. In this work, NiCuZn ferrite samples with different Cu contents were prepared by a two-step sintering method. First, the optimal temperatures of the two-step sintering method (1025/925 °C) were confirmed, thereafter the influence of the Cu content on the crystal structure, microstructure, magnetic and dielectric properties of NiCuZn ferrite were studied in detail. Structural characterization showed that an increase in Cu content promoted grain growth and resulted in NiCuZn ferrites with a denser microstructure and decreased porosity. However, a second phase of CuO formed once the content of Cu (x value) reached 0.16. The magnetic hysteresis loops revealed that the saturation magnetization increased as x increased and the highest value of 57.3 emu/g was obtained at x = 0.14. The dielectric property measurement showed that increasing the Cu content could improve the dielectric constant and reduce the dielectric loss. The permeability measurements showed an increase in permeability with Cu content from x = 0.10 to x = 0.14 and a decrease when x = 0.16. Consequently, a NiCuZn ferrite with an appropriate microstructure and with high permeability (μ'=855), low magnetic loss (tanδμ = 0.02), and high saturation magnetization (57.3 emu/g) could be obtained at a Cu content of x = 0.14 and sintering temperatures of 1025/925 °C in the two-step sintering method. This NiCuZn ferrite provides new guidance for developing RF frequency multilayer inductors.

SOFT CHEMISTRY ROUTE TO THE PREPARATION OF LOW-TEMPERATURE SINTERED FERRITES FOR HIGH-PERFORMANCE MULTILAYER CHIP INDUCTORS

Low-temperature sintered hexaferrites for high-frequency multilayer chip inductors

Preparation of low-temperature sintered Mn doped Mg-Cu-Zn ferrites by sol-gel self-combustion method

Preparation and Performance of NiCuZn–Co2Y Composite Ferrite Material

Evaluation of the Electromagnetic Characteristics on Ag/NiCuZn Ferrite Sintered Bodies

Characterization and Low-Temperature Sintering of Ni0.5Zn0.5Fe2O4 Nano-Powders Prepared by Refluxing Method

Structure, Morphology, and Magnetic Properties of High-Performance NiCuZn Ferrite

Novel Ferrimagnetic Material for Fabricating Multilayer Chip Inductors —low‐temperature‐sintered Ba3Co2−xZnxFe24O41 Hexaferrites

Soft Ferrite Materials for Multilayer Inductors

Synergy effects between Li0.42Zn0.27Ti0.11Fe2.2O4 nanoparticles and CuO-Bi2O3 mixtures in low-temperature sintered LiZnTi ferrites with enhanced gyromagnetic and microwave dielectric properties

Investigation on structure and properties of low-temperature sintered composite ferrites

Preparation of the Percolative Nickel-Zinc Ferrite/Barium Titanate Composite Ceramics with Liquid-Solid Hybrid Method

Preparation and electromagnetic properties of low-temperature sintered ferroelectric–ferrite composite ceramics

Preparation and Investigation of (ni0.15cu0.25zn0.60)fe1.96o4 Ferrite with Very High Initial Permeability from Self-Propagated Powders

Improved magnetic and dielectric properties for NiZn ferrites by using cold sintering-assisted process

The Effect of Particle Size of Nano NiZnCu Ferrite Powders on Sintering Behavior, Microstructure and Electromagnetic Properties

High Permeability NiZn Ferrites Sintered at a Low Temperature of 930℃

Magnetic Properties of Ni-Zn Ferrite Ceramics Prepared from the Blend of Powders

Synthesis of nanocrystalline NiCuZn ferrite powders by sol–gel auto-combustion method

Preparation and Investigation of Low Firing Temperature NiCuZn Ferrites with High Relative Initial Permeability

Magnetic and dielectric properties of NiCuZn ferrite with optimized Cu content and sintered by a two-step process