Abstract:While the phase separation of binary mixtures of chemically different polymer-grafted nanoparticles (PGNPs) is observed to superficially resemble conventional polymer blends, the presence of a "soft" polymer-grafted layer on the inorganic core of these nanoparticles qualitatively alters the phase separation kinetics of these "nanoblends" from the typical pattern of behavior seen in polymer blends and other simple fluids. We investigate this system using a direct immersion annealing method (DIA) that allows for a facile tuning of the PGNPs phase boundary, phase separation kinetics, and the ultimate scale of phase separation after a sufficient "aging" time. In particular, by switching the DIA solvent composition from a selective one (which increases the interaction parameter according to Timmerman's rule) to an overall good solvent for both PGNP components, we can achieve rapid switchability between phase-separated and homogeneous states. Despite a relatively low and non-classical power-law coarsening exponent, the overall phase separation process is completed on a time scale on the order of a few minutes. Moreover, the roughness of the PGNP blend film saturates at a scale that is proportional to the in-plane phase separation pattern scale, as observed in previous blend and block copolymer film studies. The relatively low magnitude of the coarsening exponent n is attributed to a suppression of hydrodynamic interactions between the PGNPs. The DIA method provides a significant opportunity to control the phase separation morphology of PGNP blends by solution processing, and this method is expected to be quite useful in creating advanced materials.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c03357?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c03357</a>.AFM images for as-cast and thermally annealed films, AFM images for as-cast films with different PMMA-SiO2/PS-SiO2 mass ratios, 1D power spectrum, ToF-SIMS profiles, in situ AFM image, discussion on ToF-SIMS sputtering energy, discussion on the coarsening exponent (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c03357/suppl_file/nn1c03357_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Studies on the Gradient Phase Morphology of Polymer Blends Caused by Temperature Gardient

Phase Behavior of Ternary Homopolymer/Gradient Copolymer Blends

Study on the formation rate of gradient phase morphology in the polymer blends

Formation of Gradient Phase-Structure During Annealing of A Polymer Blend

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Interdiffusion Behavior under A Temperature Gradient Field in A Poly(Ethylene-Co-Hexene)/Poly(Ethylene-Co-Butene) System

Controls of Gradient Morphology and Surface Properties of Polymer Blends

Rheology and Morphology of Phase-Separating Polymer Blends

Study of the Coarsening Process in Polymer Mixtures Melt with Different Interfacial Tension under 2-D Conditions

Effect of Interfacial Tension on the Formation of the Gradient Morphology in Polymer Blends

Interface-Induced Coarsening Process in Polymer Blends.

Morphology Evolution of Miscible Blends Between Crystalline Pa6 and Amorphous Pa6icot

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Interplay between thermal and compositional gradients decides the microstructure during thermomigration: a phase-field study

The Effect of Conductive Heat Transfer on the Morphology Formation in Polymer Solutions Undergoing Thermally Induced Phase Separation

Morphological-evolution Pathway During Phase Separation in Polymer Solutions with Highly Asymmetrical Miscibility Gap.

Effects of temperature gradient on the interface microstructure and diffusion of diffusion couples: phase-field simulation

Phase Morphologies And Viscoelastic Relaxation Behaviors For An Lcst-Type Polymer Blend Composed Of Poly(Methyl Methacrylate) Poly[(Alpha-Methyl Styrene)-Co-Acrylonitrile]

Phase morphology evolution upon melt annealing treatment and corresponding mechanical performance of impact-resistant polypropylene copolymer

Control of Phase Morphology of Binary Polymer Grafted Nanoparticle Blend Films via Direct Immersion Annealing

Dynamic Rheological Behavior and Morphology Near Phase-Separated Region for a LCST-type of Binary Polymer Blends