Abstract:luminum alloys are characterized by low abrasive wear resistance, which significantly restricts their wide use in technological environments, especially if they contain abrasive particles. The method of pulse anodizing, which consists in periodically changing the current density, allows to improve the hardness and abrasive wear resistance. However, the influence of temperature on these processes has not been sufficiently studied. The process of pulsed hard anodizing was carried out in a 20% aqueous H2SO4 solution at a current density of 1.4 A/dm2 with a frequency of 100 Hz and a sparability of 75%. The temperature of the electrolyte during the formation of layers was maintained at -5°±1С, 0°С±1, +5°С±1, +10°С±1. The duration of synthesis was 60 minutes. At low temperatures of less than -5С due to the low speed of electrochemical processes, oxide layers with reduced microhardness and thickness are synthesized. At the same time, the phase analysis recorded the synthesis of an oxide layer based on aluminum with the content of two phases: the synthesis of the anodized layer begins with the formation of hydrated aluminum oxide Al2O3•H2O. As the anodizing temperature increases, the rate of electrochemical processes increases, which leads to an increase in the thickness of the anodized layer and its microhardness. At temperatures of 0С and -5С, the anodized layer contains only one phase - Al2O3 H2O, (boehmite) with one water molecule. At anodizing temperatures of +5С and -8С, the anodized layer is formed again in the form of two phases - Al2O3 3H2O (gibbsite) and Al2O3H2O (boehmite) and at a temperature of +10С only Al2O3 3H2O (gibbsite). At a temperature lower than –10°C, the electrolyte turns into a gel-like substance in which electrochemical reactions practically stop, so the synthesis of a pulsed solid anodized layer at a temperature of –5°C was started. However, as a result of the synthesis at T = –5 С and then even higher (up to 0С), the average thickness of the pulsed hard anodized layer increased from 83 μm to 110 μm. With further increase in the temperature of the electrolyte, the thickness decreased and at an electrolyte temperature of +10 С it was 80 μm. Such a change in the thickness of the anodized layer depending on the synthesis temperature was explained by two opposing processes that occur during anodization. As the temperature of the electrolyte increases, the process of synthesis of the layer intensifies first of all, and therefore the thickness of the obtained layer should constantly increase with the increase of the synthesis temperature. However, an increase in the temperature of the electrolyte also intensifies the surface dissolution of the anodized layer, which is aimed at reducing the thickness of the anodized layer. And when the rate of dissolution of the anodized layer begins to exceed the rate of its synthesis, its thickness begins to decrease. Conclusions: 1) The more water and sulfur molecules in the anodized layer, the lower its microhardness and abrasive wear resistance. 2) The minimum wear of the anodized layer, which means the highest wear resistance, was recorded for layers synthesized at an anodization temperature of -8oС, and the maximum wear and lowest wear resistance at an anodization temperature of -5oС. 3) High wear resistance of anodized layers synthesized at electrolyte temperatures from -8 to +10oС under conditions of friction without lubrication is caused by the presence of crystalline water in the anodized layer.

Pulsed Hard Anodizing of Aluminium Alloys at Room Temperature and Analysis on Microstructure of Anodic Films

Study of the Influence of the Temperature of the Electrolyte During Pulse Anodization on the Properties of the Surface Layers of Technical Aluminum

Annealing Effect of High-Density Pulsed Electric Current Treatment on Cold-Rolled 6061 Aluminum Alloy

Anti-Corrosion Property of Atomic Layer Deposition Films for Anodized Aluminum

Effect of Pre-Anodized Film on Micro-Arc Oxidation Process of 6063 Aluminum Alloy

Unveiling Thermal and Athermal Effects in Strain Hardening Removal of A6061 Aluminum Alloy

Anodic Film Growth on Al–Li–Cu Alloy AA2099-T8

Effect of the Anodizing Temperature on Microstructure and Tribological Properties of 6061 Aluminum Alloy Anodic Oxide Films

Microstructure Effects on Anodizing High-Silicon Aluminium Alloy AlSi12Cu1(Fe) under Various Surface Conditions and Power Modes

Anomalous Layer-Thickening During Micro-Arc Oxidation of 6061 Al Alloy

Anodization of AZ91 Magnesium Alloy in Alkaline Solution Containing Silicate and Corrosion Properties of Anodized Films

Effect of Electrical Parameters on the Structure and Properties of Aluminum Foil Microarc Oxidation Film

Growth mechanism of micro-arc oxidation film on 6061 aluminum alloy

Anodic Layer Growth on 1050 and 2024 Aluminium Alloys in Presence of Etidronic Acid : Changes in Morphology and Structure

Effect of voltage on structure and properties of 2024 aluminum alloy surface anodized aluminum oxide films

The Anodization of Zk60 Magnesium Alloy in Alkaline Solution Containing Silicate and the Corrosion Properties of the Anodized Films

Influence of Normal-to-High Anodizing Voltage on AAO Surface Hardness from 1050 Aluminum Alloy in Oxalic Acid

Structural and Hydrophilic Properties of Nanoporous Aluminium Oxide Film as a Function of Voltage Anodization

Rapid hardening induced by electric pulse annealing in nanostructured pure aluminum

Formation behavior of anodizing films on various aluminum alloys in oxalic acid solution

Effect of Citric Acid Hard Anodizing on the Mechanical Properties and Corrosion Resistance of Different Aluminum Alloys