Abstract:Effects of varied levels of cerium (28 × 10–6, 65 × 10–6 and 150 × 10–6) on inclusions in a high-carbon chromium bearing steel at different stages (before adding cerium, after adding cerium for 1, 5, 10 min and ingot) were studied using laboratory experiments. An automatic scanning electron microscope system with energy-dispersive spectroscopy was used to analyze the amount, composition, size and morphology of inclusions in the steel at different stages. When the cerium content in the molten steel increased from 0 to 150 × 10–6, the evolution sequence of inclusions was as follows: Al2O3 → CeAl11O18 → CeAlO3 → Ce2O2S. After 28 × 10–6 cerium was added, Al2O3 inclusions were modified into CeAl11O18 inclusions in the molten steel and then were further transformed into Al2O3 and CeAlO3 inclusions in the solid steel during cooling. With the addition of 65 × 10–6 cerium, inclusions in the molten steel were modified into CeAlO3 and a small number of Ce2O2S inclusions. When the addition amount of cerium increased to 150 × 10–6, inclusions were transformed to Ce2O2S. The size of inclusions in the molten steel decreased obviously with cerium addition. On the other hand, the size of inclusions increased during the cooling process in solid steels of No. 1 steel (with 28 × 10–6 cerium) and No. 2 steel (with 65 × 10–6 cerium). During the cooling process, unmodified MnS inclusions were precipitated in the solid steel of No. 1 steel and wrapped outside the Al2O3 and CeAlO3 inclusions to form large complex inclusions. During the cooling process of No. 2 steel, the inclusion size of CeAlO3 increased due to the collision and polymerization. In the No. 3 steel (with 150 × 10–6 cerium), the average size of inclusions decreased rapidly and remained at a lower size during the cooling process, which was beneficial to improving the fatigue life of the steel.

Effects of deleterious impurities and cerium modification on intrinsic and extrinsic toughening levels of Al-Li based alloys

Effects of deleterious impurities and cerium modificationon intrinsic and extrinsic toughening levels of AI-Li based alloys

Effect of cerium on fracture toughness of alloy 2090 sheets containing Alkali metal impurities

Effect of Cerium on Microstructure, Texture and Properties of Ultrahigh-Purity Copper

Effect of Impurities and Cerium on Stress Concentration Sensitivity of Al-Li Based Alloys

Effect of minor cerium additions on microstructure and mechanical properties of cast Al – Cu – Mg – Ag alloy

EFFECTS OF IMPURITIES AND Ce ON FRACTURE BEHAVIOUR OF 8090 ALLOY SHEETS IN DIFFERENT ORIENTATIONS

Stress concentration sensitivity of Al–Li based alloys with various contents of impurities and cerium addition

Evolution of Inclusions with Cerium Addition and Effects of C-containing Rare Earth Inclusions on the Toughness of Ultra-High-strength Structural Steel

Effect of Cerium on Microstructures and Mechanical Properties of Az61 Wrought Magnesium Alloy

Effect of Cerium Addition on Microstructure and Mechanical Properties of As-Cast High Grade Knives Steel

Microstructural control of toughness in aluminium-lithium alloys

Effects of Cerium Content on the Nonmetallic Inclusions and Impact Toughness of Transformation‐Induced Plasticity Steel

Effect of cerium addition on non-metallic inclusions in a high-carbon chromium bearing steel

Microstructure and Mechanical Properties of Ti44Al6Nb Alloys with Different Cerium Contents

Effect of the addition of cerium on the microstructure evolution and thermal expansion properties of cast Al-Cu-Fe alloy

Influence of cerium treatment on inclusion modification and as-cast microstructure of high-strength low-alloy steel

Effect of Ce Content on the Microstructure and Mechanical Properties of Al-Cu-Li Alloy

Effect of Cerium-rich Mischmetal on Microstructures of As-cast A356 Alloy

Effect of Cerium Addition on Microstructure and Mechanical Properties of the Ductile Iron

Effect of Cerium on the Cleanliness and Properties of an Al‐Killed Low‐Sulfur Steel