Abstract:In order to investigate the effect of WC grain size on coatings' properties and abrasive wear performance, a few WC-20Cr(3)C(2)-7Ni coatings with three different WC grain sizes were deposited by the high-velocity oxy-fuel (HVOF) thermal spray process. The phase compositions, microstructures, and mechanical properties of the coatings were investigated. Furthermore, the two- and three-body abrasive wear performances of the three coatings were tested by using SiC and SiO(2)abrasives, respectively. The results show that all the three coatings were composed of WC, Cr3C2, and the Ni binder as well as the (W,Cr)(2)C phase. The abrasive wear resistance of the WC-20Cr(3)C(2)-7Ni coating monotonously increased with increasing WC grain size when the SiC abrasive was used in the two- and three-body abrasive wear tests. However, the wear resistance trend was reversed when the SiO(2)abrasive was used in the three-body abrasive wear test. The specific wear rate of the WC-20Cr(3)C(2)-7Ni coating exposed to the SiC abrasive under the two-body abrasive wear test was the largest. The wear resistance of the coatings was more significantly affected by the hardness of the abrasive particles than the size of carbides present within the coating. The high hardness of SiC can cut both the carbide and the binder phase of the WC-based cermet coatings, resulting in a high wear rate, whereas the low hardness of SiO(2)cuts and/or scratches the binder initially, and then it dislodges the carbides from the matrix. The dislodged carbides which were subsequently pulled out from the matrix by the repeated impact of the SiO(2)abrasives result in a milder wear rate.

Effect of Powder Type on the Relationship Between Spray Parameters and Properties of Hvof Sprayed Cr3c2-Nicr Coatings

Effect of spray conditions on the properties of HVOF Cr3C2-NiCr coatings

Effect of Spray Conditions on the Properties of HVOF Sprayed Cr3C2-NiCr Coatings.

Erosion Performance of HVOF-Sprayed Cr 3 C 2 -Nicr Coatings

Influence of Spray Parameters on Sliding Wear Properties of HVOF Sprayed Fe-Based Amorphous Coatings

Microstructural Characterization and Abrasive Wear Performance of HVOF Sprayed Cr3C2–NiCr Coating

Abrasive Wear Resistance of HVOF Deposited Cr3C2-NiCr Coatings

The Microstructure and Erosion Wear Performance of HVOF-Sprayed Cr3C2-NiCr Coatings with Different Feedstock Powder

Dominant Effect of Carbide Rebounding on the Carbon Loss During High Velocity Oxy-Fuel Spraying of Cr3C2–NiCr

Effect of Fuel Flow on Microstructure and Erosion Performance of HVOF Sprayed Cr3C2 -Nicr Coating

High temperature wear resistance of HVOF sprayed Cr3C2-25NiCr coating

Effect of Particle and Carbide Grain Sizes on a HVOAF WC-Co-Cr Coating for the Future Application on Internal Surfaces: Microstructure and Wear

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Method for Quantitative Evaluation of Carbon and Carbide Loss During HVOF Spraying of Cr3C2-NiCr Coating

Model of the Abrasive Wear of HVOF Deposited Cr3C2-NiCr Coating

Effect Of Wc Grain Size And Abrasive Type On The Wear Performance Of Hvof-Sprayed Wc-20cr(3)C(2)-7ni Coatings

Effect of WC Grain Size and Abrasive Type on the Wear Performance of HVOF-Sprayed WC-20Cr<sub>3</sub>C<sub>2</sub>-7Ni Coatings

Effect of solid carbide particle size on deposition behaviour, microstructure and wear performance of HVOF cermet coatings

Sliding Wear Behavior of HVAF-sprayed Coarse-Grained and Nanocrystalline NiCrC Coatings

Comparison on multi-angle erosion behavior and mechanism of Cr3C2-NiCr coatings sprayed by SPS and HVOF

The Influence of Powder Types and Plasma Spray Conditions on Abrasive Wear of Nanostructured and Conventional Al2o3/Tio2 Coatings