Abstract:Normally, the microstructure of eutectic and hypereutectic Al-Si alloys consists of Al-Si eutectic or Al-Si eutectic + Si I , that is why they have good wear-resistance properties, but their ductility decreases somewhat, which can be improved by the appearance of non-equilibrium α-aluminum grains. In present work, a recrystallization and partial melting (RAP) technique was applied in the preliminary research to investigate the solidification behavior of the eutectics at high cooling rate. The results show that numerous α-Al dendrites appeared instead of the eutectic structure. In the followed researches, the combination of some technological procedures, based on the competitive growth of dendrites and eutectics, such as heterogeneous nucleation and high cooling rate, were applied: A413.0 and A390.0 alloys were melted in resistant furnace and poured into a mold, made of copper at one side and of steel at another, which is connected to the temperature measuring device via four K-class thermocouples. The various pouring regimes: gravity, via 45 0 tilt cooling slope and injection with Argon gas for 2 min. before pouring, were applied at different temperatures of 680, 650, 630 0 C. The results show that the hetero-structure of eutectic and hyper-eutectic Al-Si alloys, consists of non-equilibrium α-Al grains, primary silicon and eutectics was obtained. Grain size varies with cooling rate, with minimum value of 10 μm when the specimen thickness is 5 mm. Non-dendritic grains were achieved with semi-solid treatment (pouring via cooling slope). The elongation of alloy is expected to be enhanced due to the appearance of α-Al grains.

Solidification characteristics of highly undercooled Ag-Ge eutectic alloys

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Solidification behavior and microstructure of Ag–Cu eutectic alloy at different sub-rapid cooling rates

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Refining Mechanism and Elevated-Temperature Mechanical Properties of Al-Ce Alloys Solidified under Super Gravity Field

Solidification Microstructure in a Supercooled Binary Alloy

Structural and Dynamical Properties of Liquid Ag74Ge26 Alloy Studied by Experiments and Ab Initio Molecular Dynamics Simulation

Growth Mechanism of Eutectic Si in Super-Gravity Solidified Al-Si Alloy During Annealing

Solidification Microstructure Evolution and Grain Refinement Mechanism under High Undercooling of Undercooled Ni90Cu10 Alloys

Influence of Super Gravity Field on Solidification Structures of Cu98.4 Cr1.6 Alloy

Influence of Super-Gravity Coefficient on Spatial Distribution of Solidification Structure in Al-14.5Si Alloys

Bergman-type Medium-Range Order in Rapidly Quenched Ag0.74Ge0.26 Eutectic Alloy Studied by Ab Initio Molecular Dynamics Simulation

Grain Refinement Mechanism at High Undercooling of Ni80Cu20 Alloy

Re-Examination of the Microstructural Evolution in Undercooled Co-18.5at.%B Eutectic Alloy

Systematic discovery of new nano-scale metastable intermetallic eutectic phases in laser rapid solidified Aluminum-Germanium alloy

Rapid Solidification Structure Refinement Mechanism in Highly Undercooled Cu Based Ternary Alloys

Effect of Minor Addition of Co on Nonequilibrium Solidification of Deeply Undercooled Cu Based Alloys

Formation of Heterostructure with Appearance of α-Al Phase in Hyper- and Eutectic Al-Si Alloys by Solidification at High Rate

Effects of Ag, Co, and Ge additions on microstructure and mechanical properties of Be-Al alloy fabricated by investment casting

Structural Evolution of Low-Temperature Liquid GaIn Eutectic Alloy