Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Study of the incorporation mechanism between particulates and matrix of SiC/Al composites by spray co-deposition

Effect of SiC Deposition Behavior on Microstructure and Mechanical Properties of Cold-Sprayed Al5056/SiC Composite Coatings

Deposition behavior and mechanism of thermal sprayed SiC

Achieving ultrafine grain strengthening C f /SiC-GH3536 joints brazed with Cu-Ti-WC composite interlayer via cold spray additive manufacturing

Study on microstructure evolution and reaction mechanism of in-flight Ti–Si–C agglomerates during reactive plasma spraying using in situ water quenching

Deposition mechanism of ceramic reinforced metal matrix composites via cold spraying

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

AI-Li/SiCp composites and Ti-AI alloy powders and coatings prepared by a plasma spray atomization (PSA) technique

Study on the formation mechanism of surface defects in the processing of large particle SiCp/Al composites

Numerical Simulation of Microstructure of Al-Si/Sicp Composites During Stir Casting Process with Particle Pushing Model

The Influence of Cold and Detonation Thermal Spraying Processes on the Microstructure and Properties of Al-based Composite Coatings on Mg Alloy

Characteristics and Sintering Behaviors of SiC-AIN Composite Powders Obtained by Spray Drying

TEM characterization and reaction mechanism of composite coating fabricated by plasma spraying Nb–SiC composite powder

Numerical simulation and quantitative assessment of particle distribution in SiC/Al-Si composites

Cold Sprayed Additive Manufacturing of SiC/Al Metal Matrix Composite: Synthesis, Microstructure, Heat Treatment and Tensile Properties

Numerical Simulation and Experimental Study of Deposition Behavior for Cold Sprayed Dual Nano HA/30 wt.% Ti Composite Particle

Microstructure and Thermal Properties of Inert Plasma-Sprayed Tungsten Coating on SiC-Coated Carbon/Carbon Composites

3D microstructure simulation of stir casting SiCp/Al-7.0%Si composites

Droplet Impact-Induced Molten Pool Dynamics and Particle Migration Patterns During TIG-assisted Droplet Deposition Manufacturing of SiC Particle-Reinforced Al–Si Alloy

Study on the densification of composite coating particles of α-Al2O3–SiO2