Abstract:Objective: To further study the most suitable parameters for automatic full crown preparation using oral clinical micro robot. Its purpose is to improve the quality of automated tooth preparing for the system and to lay the foundation for clinical application. Methods: Twenty selected artificial resin teeth were used as sample teeth. The micro robot automatic tooth preparation system was used in dental clinic to control the picosecond laser beam to complete two dimensional cutting on the resin tooth sample according to the motion planning path. Using the laser scanning measuring microscope, each layer of cutting depth values was obtained and the average value was calculated. The monolayer cutting depth was determined. The three-dimensional (3D) data of the target resin teeth was obtained using internal scanner, and the CAD data of full-crown tooth preparation was designed by CAD self-develged software. According to the depth of the single layer, 11 complete resin teeth in phantom head were automatically prepared by the robot controlling the laser focused spot in accordance with the layer-cutting way. And the accuracy of resin tooth preparation was evaluated with the software. Using the same method, monolayer cutting depth parameter for cutting dental hard tissue was obtained. Then 15 extracted mandibular and maxillary first molars went through automatic full crown tooth preparation. And the 3D data of tooth preparations were obtained with intra oral scanner. The software was used to evaluate the accuracy of tooth preparation. Results: The results indicated that the single cutting depth of cutting resin teeth and in vitro teeth by picosecond laser were (60.0±2.6) and (45.0±3.6) μm, respectively. Using the tooth preparation robot, 11 artificial resin teeth and 15 complete natural teeth were automatically prepared, and the average time were (13.0±0.7), (17.0±1.8) min respectively. Through software evaluation, the average preparation depth of the occlusal surface of 11 resin teeth was approximately (2.089±0.026) mm, the error was about (0.089±0.026) mm; the average convergence angle was about 6.56°±0.30°, the error was about 0.56°±0.30°. Compared with the target preparation shape, the average shape error of the 11 resin tooth preparations was about 0.02-0.11 mm. And the average preparation depth of the occlusal surface of 15 natural teeth was approximately (2.097±0.022) mm, the error was about (0.097±0.022) mm; the average convergence angle was about 6.98°±0.35°, the error was about 0.98°±0.35°. Compared with the target preparation shape, the average shape error of the 15 natural tooth preparations was about 0.05-0.17 mm. Conclusions: The experimental results indicate that the automatic tooth preparation for resin teeth and the teeth were completed according to the specific parameters of the single cutting depth by the micro robot controlling picosecond laser respectively, its preparation accuracy met the clinical needs. And the suitability of the parameter was confirmed.

Research and implementation for parametric design of tooth preparation

[Application of Computer Aided Design/computer Aided Manufactured Techniques in Mandible Defect Reconstruction].

Computer-aided Design of Tooth Preparations for Automated Development of Fixed Prosthodontics.

Digital Modeling Technology for Full Dental Crown Tooth Preparation

Digital Interactive Design and Robot-Assisted Preparation Experiment of Tooth Veneer Preparation: An in Vitro Proof-of-Concept

An Automatic Tooth Preparation Technique: A Preliminary Study

Computer-assisted methods for obtaining quantitative parameters of tooth preparation for crown

[Research status of tooth preparation quantitative guide technique].

Digital Inlaid Design Based on Anatomical Characteristics and Preliminary Implementation of Its Program

[Study on the appropriate parameters of automatic full crown tooth preparation for dental tooth preparation robot]

Preliminary Study on the Quantitative Analysis of Tooth Preparation for Crown Based on Digital Model

Study on Digital Teeth Selection and Virtual Teeth Arrangement for Complete Denture

Preliminary Application and Evaluation of Digital Step-by-step Tooth-Preparation Templates

An Algorithm for Cutting Preparation Line on Dental Mesh Surface

Investigation on the Effectiveness of Digital Scanning Combined with Reverse Engineering Technology in Demonstrating Full Crown Tooth Preparation

[Research and Development of Computer Aided Design and Rapid Prototyping Technology for Complete Denture].

3D Evaluation of Accuracy of Tooth Preparation for Laminate Veneers Assisted by Rigid Constraint Guides Printed by Selective Laser Melting.

3D Printing of Drill Guide Template for Access Cavity Preparation in Human Molars: a Preliminary Study

Preliminary Study on Computer-Aided Design of Full Crown

[Initial Evolution Research for Design and Process Accuracy of One Type of Domestic Computer Aided Design Soft and Computer Aided Manufacture].

Personalized Design and Rapid Prototyping of Tooth Piles Using CAD/CAM