Abstract:It is known that the interest in manufacturing in a vacuum environment has increased in recent years. Thus, the wear behavior of mechanical tools under vacuum conditions has critical importance. However, adhesion and cold-welding problems between tool and working piece in vacuum conditions lead to poor wear properties and severe coefficient of friction values. Surface treatment methods such as physical vapor deposition coatings can eliminate these undesirable consequences, especially transition metal nitrides. In this study, TiAlN, TiSiN, and TiAlN/TiSiN films were coated on AISI H13 tool steels employing the cathodic arc evaporation technique. Whether the coatings grown to the substrate surface have a positive contribution to the wear performance of the substrate in the ambient air and vacuum environment was answered. Scanning electron microscope, energy dispersive spectrometer, and X-ray diffractometer analyses were used to attain structural properties. The hardness was measured using a nano-hardness tester, and the adhesion properties were determined by a scratch test. The wear behavior of the substrate and coating samples are determined under 2 N constant normal load and using WC-6%Co counter bodies under ambient air and vacuum conditions. The hardness of samples improved owing to surface coatings, and the highest nano-hardness value was determined from the TiSiN coatings as 39.42 GPa, which is ∼700% greater than the substrate. It has been observed that coated samples have superior wear performance in both wear conditions. Besides, it is determined that those tested under a vacuum condition showed superior wear resistance than the samples tested under ambient air. While TiSiN film exhibits the highest wear resistance in ambient air, the TiAlN/TiSiN layer is the best in a vacuum environment. Owing to the deposited coatings, the seizure mechanism between the friction surfaces, which is frequently encountered in the vacuum environment, is prevented, and a fascinating improvement in terms of friction coefficient is achieved.

Vacuum tribological properties of a Ti-46Al-2Cr-2Nb intermetallics

DRY SLIDING WEAR OF Ti-6Al-4V ALLOY AT LOWTEMPERATURE IN VACUUM

High Temperature Tribological Behavior of a Ti-46Al-2Cr-2Nb Intermetallics

Dry sliding wear of Ti-6Al-4V alloy in air and vacuum

Effects of Vacuum Degree on Tribological Behavior of Tib2/Al Composites

Study on dry sliding wear of TC4 alloy in vacuum

Dry Friction Characteristics of Ti-6Al-4V Alloy under High Sliding Velocity

Ti6Al4V interacting with Al 2 O 3 under Ambient and Vacuum Conditions: Effect of Plastic Deformation and Tribo-Chemical Reactions on Wear Mechanisms

The Relationships Between Tribological Behaviour and Heat-Transfer Capability of Ti6Al4V Alloys

Study On The Tribological Properties Of Titanium Alloys Sliding Against Wc-Co During The Dry Friction

Tribological properties of in-situ PVD TiAlN, TiSiN, and TiAlN/TiSiN coatings under ambient air and vacuum environment

Effect of Vacuum Heat Treatment on the Microstructure and Tribological Property of Ti–6Al–4V Alloy with Cu Coating

Dry Sliding Wear Behavior of Ti-6Al-4V Alloy in Air

Influence of Interfacial Tribo-Chemical and Mechanical Effect on Tribological Behaviors of TiN Film in Different Environments

MORPHOLOGY OF WEAR DEBRIS DURING DRY SLIDING OF Ti6Al4V/TiC COMPOSITE AT ELEVATED TEMPERATURES IN VACUUM CONDITIONS

Friction and Wear Performance of Titanium Alloys against Tungsten Carbide under Dry Sliding and Water Lubrication

Effect of TiB2 on Dry-Sliding Tribological Properties of TiAl Intermetallics

Wear performance of Ti-6Al-4 V titanium alloy through nano-doped lubricants

Effect of Sliding Velocity in Vacuum on Tribological Behavior of Nitrided 2cr13 Steel

Tribological Properties of Groove-Textured Ti-6Al-4V Alloys with Solid Lubricants in Dry Sliding against GCr15 Steel Balls

Sliding Wear Behavior of Intermetallic Ti-45Al-2Nb-2Mn-(at%)-0.8vol%TiB2 Processed by Centrifugal Casting and Hot Isostatic Pressure: Influence of Microstructure