Abstract:Despite the excellent improvements in high fields resulting from the adoption of REBa2Cu3O x (REBCO)-coated conductors (CCs), the resulting stress and strain due to winding tension, cooling stress, and the screening-current-induced Lorentz force may lead to severe plastic deformation and degradation of superconductivity. Therefore, it is essential to understand the comprehensive electromechanical behavior and deformation mechanism of high-field REBCO magnets. In this paper, multistep finite element analysis is designed to simulate the electromechanical behavior of REBCO coils after the winding, coolingdown, and charging processes. All major constituent materials including the mandrel, CCs, cowinding reinforcement, and over-banding are considered in the mechanical models to emulate contact–separation behavior between them. In addition to contact nonlinearity, an intrinsic elastoplastic property is introduced to predict the plastic deformation observed in experiments. To reveal the screening-current effect, the distributions of the screening current and the magnetic field are analyzed by solving the T-A formulation of Maxwell’s equations using a homogeneous technique. Then, with the electromagnetic load acting as a body force, the electromagnetic stress and strain are computed and experimentally validated for a pancake coil, including the transport current and external field. Finally, the electromechanical behavior under a Lorentz load is investigated by considering the accumulation of stress and strain due to winding tension and cooling down. The simulation results reveal that the winding tension and thermal stress affect the final stressstates in the fully charged state and therefore the electromechanical properties. Both plastic deformation and possible degradation are more likely to occur in the outermost tape of several pancakes due to the influence of screening-current-induced stress and strain. In addition, this work further analyzes the effect of the current sweep reversal method, which could be favorable in reducing the screening-current-induced high stress and strain in the steady state.

Electromagnetic Forces of High-T (C) Superconducting Coated Conductor Coils Subjected to Sinusoidal Traveling Magnetic Fields

Electromagnetic-mechanical Coupling Analysis of High-Temperature Superconducting Racetrack Coil

Experiment and Simulation of Rebco Conductor Coils for an Hts Linear Synchronous Motor

Three-dimensional simulation of the coupled electromagnetic-mechanical responses in a no-insulation racetrack coil

Design, Fabrication, and Testing of a YBCO Racetrack Coil for an HTS Synchronous Motor with HTS Flux Pump

Performance of a Small-Scale High Temperature Superconducting Linear Synchronous Motor Prototype

Design and Key Performance of 2G HTS Coils for High Speed Superconducting Maglev Application

A Coupled Electromagnetic-Mechanical Model and Contact Behavior of the Superconducting Coils

Design of a 400 N and 12 mm Mechanical Air Gap High Temperature Superconducting Linear Synchronous Motor

Magnetic Field Distribution Around Superconducting Coils in Ferromagnetic Environment

Electromagnetic Properties Analysis On Superconducting Magnet Coil For Magnetoplasmadymamic Thruster

Numerical Analysis of the Electromechanical Behavior of High-Field REBCO Coils in All-Superconducting Magnets

Partial Force Calculation and Structural Strength Analysis of Null-Flux Coil for Superconducting Electrodynamic Suspension Train

A single-sided linear synchronous motor with a high temperature superconducting coil as the excitation system

Influence of structural parameters on electromagnetic properties of high temperature superconductor linear induction motor

Experimental Study of the Electromagnetic Forces of a HTS Bulk Magnet Subjected to Sinusoidal Traveling Magnetic Field

Harmonic Magnetic Field Analysis Method and Modeling of Double-Sided Air-Cored Superconducting Linear Synchronous Motor for EDS Train

Effective 3-D FEM for Large-Scale High Temperature Superconducting Racetrack Coil

Investigation of a low-speed single-side HTS linear induction motor with different primary structures used for linear metro

Electromagnetic analysis of high temperature superconducting linear induction motor for rail transit

3D finite element modelling on racetrack coils using the homogeneous <i>T-A </i>formulation