Effects of Spray Characteristics of Emulsified Diesel on Soot Emissions in a Constant Volume Chamber
Ming Huo,Han Wu,Nan Zhou,Karthik Nithyanandan,Chia-fon F. Lee
2013-01-01
Abstract:Emulsions of diesel and water are a potential solution to meet the increasingly stringent emission regulations as they are able to simultaneously reduce both nitrogen oxide (NOx) emissions and particulate matter (PM) from diesel engines. The PM reduction capability is often associated with the unique atomization characteristic known as microexplosion. In this work, emulsified diesel, with the amount of water ranging between 10% and 20% by volume, was injected and combusted in an optical constant volume chamber. With controlled combustion of an acetylene mixture prior to fuel injection, the chamber is able to provide high ambient temperature and pressure to mimic the real engine operation. In this study, ambient temperatures ranging from 800K to 1200K were investigated. Mie scattering images, at 15000 fps, were first taken to record the evolution of the spray using a Phantom 7.1 high speed CCD camera coupled with a copper vapor laser as the light source. The spray images revealed longer liquid penetration and wider cone angle at the beginning stage of the injection event for emulsified fuel, supporting the occurrence of micro-explosion. The integrated broadband luminosity suggested that emulsified fuel coupled with low temperature combustion may optimize the emission control strategy. * Corresponding author: cflee@illinois.edu ILASS Americas, 25 Annual Conference on Liquid Atomization and Spray Systems, Pittsburgh, PA, May 2013 Introduction The simultaneous reduction of nitrogen oxides (NOx) and particulate matter (PM) emissions without after-treatment devices remain a challenge for compression ignition engines. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI), reactivity controlled compression ignition (RCCI), low temperature combustion (LTC) have been developed in recent years to lower the NOx and PM emissions. These technologies are generally associated with engine modifications to some extent: highly advanced injection/port fuel injection for HCCI, heavy EGR introduction for LTC, dual fuel utilization for RCCI, etc. In this respect, water emulsified fuel remains an attractive solution to reduce the NOx and PM in exhaust gas simultaneously since it can be introduced into the current fleet of diesel engines with no major modifications on the engine. [1] Numerous studies have been conducted to evaluate the engine performance by replacing diesel with emulsified fuel. [2-10] Hironori et al. [2] investigated the feasibility of using water-in-oil type emulsified fuels in small DI diesel engines and reported that lower fuel consumption and NOx emission can be achieved by the control of injection timing for W/O emulsified fuels with water content ratio less than 20%. Hountalas et al. [3] showed comparative evaluation of EGR, intake water injection and W/O emulsion as NOx reduction techniques for a heavy duty diesel engine. Watanabe and Tamura [4] introduced mono-dispersion emulsified fuel produced by their own original way using multi-porous glass and reported effectiveness of mono-dispersed emulsified fuel on simultaneous reductions of NOx, PM and fuel consumption under slow engine speed condition of 1000 RPM. Masatoshi et al. [5] studied the influence of fuel injection timing and water content on diesel engine performance and concluded that influence of the water is mainly attributed to the micro-explosion feature of emulsified fuel because the water presented in the combustion chamber by direct water injection method has almost no influence on engine performance except lowered NOx emission. The impact of cooling loss reductions on engine performance with emulsified fuel operation was investigated by Yasufumi [6] and it was determined that the reduced cooling loss improved indicated thermal efficiency. In comparison, optical studies using laser diagnostic methods for the emulsified fuels are rarely found in the literature [7-10]. Raul et al. [7] reported the spray and combustion characteristics of water-in-diesel emulsions and micro-emulsions in an optical chamber. Longer droplet penetration was reported because of the lower volatility of the water. The presence of “glowing spots” was observed in the flames of the emulsified fuel which was attributed to micro explosion. In general, the following effects on engine performance are expected with the application of emulsified fuel: the adiabatic flame temperature is lowered with the presence of water due to water evaporation heat , thus NOx emission decreases. Carbon monoxide usually declines due to more H2O available for the water gas shift reaction. Soot is also reduced, explained by a number of reasons: micro explosion of emulsified fuel enhances atomization and evaporation of the spray injected in the chamber, providing better fuel-air mixing; the ignition delay is usually extended providing more mixing time thus shift the combustion mode towards premixed combustion; the OH release from water dissociation also helps oxidizing the soot. [1] In spite of the intensive studies on droplet microexplosion [11-16], the micro-explosion phenomena are not expected to be visually observed under high pressure conditions like engine combustion. The challenge results from the fact that the water nuclei formation and bubble growth in an emulsified fuel droplet actually takes time before they can “break out” the entrapping fuel. This time scale is believed to be longer than the primary breakup time scale and comparable to the secondary breakup time scale. Therefore in theory, the micro-explosion is expected to take place downstream of the spray jet, where fine droplets may already exist due to the combined effect of a number of spray physics such as secondary breakup, evaporation, coalescence, wall impingement etc. As a consequence, it is extremely difficult to identify the droplets produced by microexplosion. The primary motivation of this study is to acquire a more comprehensive understanding of the spray and combustion characteristics of emulsified diesel under different ambient temperature conditions using experimental methods and to evaluate the impact of spray features on soot emission. Emulsified diesel with the amount of water ranged between 10% and 20% by volume was injected and combusted in an optical constant volume chamber. High speeding imaging of both MIE scattering and broadband luminosity were acquired to illustrate time resolved data. On the other hand, because of the current limitations in our understanding of the spray and jets of the emulsified fuel, the modeling of the emulsified fuel spray is still very limited. CFD spray sub-models are often calibrated with measurements of spray penetration and spreading angle in a well-defined ambient environment. In this respective, this study also serves as the CFD model calibration in the future work. Experiment Setup and Procedure Apparatus A constant volume chamber with a bore of 110 mm and a height of 65 mm is used in this study. The chamber can imitate the spray and combustion process of a diesel engine, allowing a maximum operating pressure of 18 MPa. The chamber has an open end on the top with a fused silica window installed opposite to the injector allowing optical access (See Fig 1.). The window, sealed with an energized spring seal, has dimension of 130 mm in diameter and 60 mm in thickness, with a high UV transmittance down to 190 nm. A Caterpillar hydraulic-actuated electronic-controlled unit injector (HEUI) is mounted at the bottom of the chamber. The injector is VCO type, with orifice diameter of 0.145 mm. The injection pressure and duration was kept at 700 bars and 3.5 ms respectively through the tests. The cylinder wall is heated to 380 K before the experiment to mimic the wall temperature of a diesel engine as well as to prevent water condensation on the optical windows. A quartz pressure transducer (Model: Kistler 6121), embedded in the chamber wall in conjunction with a dual mode differential charge amplifier, is responsible for recording the in-cylinder pressure. The apparent heat release rate can be calculated from this using the first law of thermodynamics [17]. The high temperature and pressure environment is created by burning a mixture of acetylene, air, and N2 using spark ignition before the injection is triggered. The details of the experiment procedure can be found in [18]. Figure 1. Schematic of the test chamber