Abstract:Silicon (Si) is a promising anode material to replace the broadly adopted graphite due to its high capacity and abundant source. However, Si anodes suffer from severe problems of huge volume change (∼300%), and the commonly used binders like poly(vinylidene fluoride) (PVDF) cannot accommodate such changes. Here, we report a tough block copolymer PVDF-b-Teflon (PTFE) binder that can coalesce pulverized Si and thus enhance the stability of Si anodes. The suspension copolymerization of vinylidene fluoride and tetrafluoroethylene produces elastic PVDF-b-PTFE with large breaking elongations of >250% and high viscosity as well as high ionic conductivity and thermal stability. We show that 5 wt % of the binder forms elastic cobweb structures in the electrode matrix that can effectively coalesce Si particles and conductive agents together, enabling long cycling stability (>250 cycles) and high rate performance (1 C) for electrodes at a commercial-level Si loading of 1 mg·cm–2. The findings point out to a promising strategy for developing highly elastic and tenacious binders for electrodes with large volume changes during the electrochemical reactions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c10005?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c10005</a>.Photos of the PVDF-b-PTFE powders and the FTIR spectra; EDS mapping and elemental contents of PVDF and PVDF-b-PTFE; XPS spectra of PVDF and PVDF-b-PTFE; mechanical strength, ionic conductivity, and electrolyte wettability of PVDF and PVDF-b-PTFE films; EIS spectra and CV curves of batteries with different binders; and electrochemical performance and SEM characterizations of NMC 622 electrodes (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c10005/suppl_file/am0c10005_si_001.pdf">PDF</a>)PVDF-b-PTFE film presenting a much higher strain with superior deformation performance (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c10005/suppl_file/am0c10005_si_002.mp4">MP4</a>)This article has not yet been cited by other publications.

Enhanced Electrochemical Properties of Tio2(B) Nanoribbons Using the Styrene Butadiene Rubber and Sodium Carboxyl Methyl Cellulose Water Binder

Crystalline SnO2 @ Amorphous TiO2 Core-Shell Nanostructures for High-Performance Lithium Ion Batteries

Water Soluble Styrene Butadiene Rubber and Sodium Carboxyl Methyl Cellulose Binder for ZnFe2O4 Anode Electrodes in Lithium Ion Batteries

Using Carboxylmethylated Cellulose As Water-Borne Binder to Enhance the Electrochemical Properties of Li4Ti5O12-Based Anodes

Water-Soluble Binders That Improve Electrochemical Sodium-Ion Storage Properties in a NaTi2(PO4)3 Anode

Enabling both ultrahigh initial Coulombic efficiency and superior stability of Na2Ti3O7 anode via optimizing binders

Novel Polymer Li-ion Binder Carboxymethyl Cellulose Derivative Enhanced Electrochemical Performance for Li-ion Batteries.

3D-Crosslinked Tannic Acid/poly(ethylene Oxide) Complex As a Three-in-one Multifunctional Binder for High-Sulfur-loading and High-Stability Cathodes in Lithium-Sulfur Batteries

Tio2(B) Nanofiber Bundles As A High Performance Anode for A Li-Ion Battery

Binder-free Carbon-Coated TiO2@graphene Electrode by Using Copper Foam As Current Collector As a High-Performance Anode for Lithium Ion Batteries

Toward Greener Lithium-Ion Batteries: Aqueous Binder-Based LiNi0.4Co0.2Mn0.4O2 Cathode Material with Superior Electrochemical Performance

Highly Elastic Block Copolymer Binders for Silicon Anodes in Lithium-Ion Batteries

Constructing a Binderless Carbon-Coated In2O3 Anode for High-Performance Lithium-Ion Batteries

Ultra-high initial coulombic efficiency of the TiO2 anode induced by the synergistic role of the electrolyte and binder for sodium-ion batteries

Ti 3 C 2 /CNTs Macroporous Conductive Network Boosts Li 4 Ti 5 O 12 -TiO 2 Anode Performance for Practical Li Ion and Mg Ion Batteries

TiO2 Coated with Carbon Via Chemical Vapor Deposition As Li-Ion Batteries Anode

Sodium Titanate Cuboid As Advanced Anode Material for Sodium Ion Batteries

Biopolymer Binders for Low‐Temperature Operation of TiNb2O7 Anode in Li‐Ion Batteries

Improving the Cycling Stability of Lithium-Ion Batteries with a Dry-Processed Cathode Via the Synergistic Effect of Carboxymethyl Cellulose and Siloxane

Amorphous Carbon Coated TiO2 Nanocrystals Embedded in a Carbonaceous Matrix Derived from Polyvinylpyrrolidone Decomposition for Improved Li-storage Performance

Mechanically Robust Tapioca Starch Composite Binder with Improved Ionic Conductivity for Sustainable Lithium-Ion Batteries