Abstract:Texture evolution, microstructure and mechanical properties of an extruded Mg-10Gd-1Zn-0.4Zr alloy during annealing were investigated. A bimodal microstructure containing coarse deformed grains and fine dynamically recrystallized grains is observed when the annealing temperature is lower than 200 °C. Many Mg 5 (Gd, Zn) phases are formed in the alloy annealed at 200 °C. Further upon increasing the annealing temperature, static recrystallization occurs and lamellar LPSO phase forms within the matrix. When the annealing temperature reaches 500 °C, an obvious grain growth is observed, and Zn 2 Zr 3 phases form. Meanwhile, the dominant texture component transforms from the basal texture ( parallel to extrusion direction) to an abnormal texture ( parallel to extrusion direction), which is attributed to the growth preference of the grains with abnormal texture. The alloy annealed at 200 °C possesses the optimal mechanical properties with the yield strength of 320 MPa, the ultimate strength of 368 MPa and elongation of 18.4 %. The contribution of each strengthening mechanism to the yield strength in annealed alloys is calculated quantitatively. Compared to the as-extruded alloy, the increment of the yield strength in the alloy annealed at 200 °C is mainly due to the increase in secondary phase strengthening, while the decrement of the yield strength in the alloy annealed at 500 °C is attributed to the reduction of grain boundary strengthening. This work sheds light on adjusting the texture and mechanical properties of the extruded Mg alloys via annealing treatment.

Influence of Microstructural Evolution on Mechanical Behaviour of Az31 Alloy Sheet Processed by Flat Extrusion Container

Mechanical Properties and Anisotropy of AZ31 Alloy Sheet Processed by Flat Extrusion Container

Influence of an Asymmetric Shear Deformation on Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet

Microstructure evolution and mechanical response of extruded AZ31B magnesium alloy sheet at large strains followed by annealing treatment

Mechanical Behavior and Microstructure Evolution for Extruded AZ31 Sheet under Side Direction Strain

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Microstructure and Mechanical Behaviour of Asymmetric Extruded Mg–3Al–1Zn Alloy Sheets

Effect of Rolling and Annealing on the Mechanical Properties and Microstructure of AZ31 Magnesium Alloy

Effect of Extrusion Processing Parameters on Microstructure and Mechanical Properties of As-Extruded AZ31 Sheets

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

Influence of Annealing Treatment on Microstructure Evolution and Mechanical Property of Friction Stir Weld AZ31 Mg Alloys

Influences of Shear Angles on Microstructures and Compression Properties of AZ31 Mg Alloy Prepared by Extrusion-Shear Process

Microstructure and Texture Evolution of AZ31 Magnesium Alloy During Rolling

Annealing Behavior Of Rolled Az31 Alloy Sheet

Microstructure and properties of AZ31 alloy by static recrystallisation at lower temperature

Evolution of Gradient Microstructure in an Extruded AZ31 Rod During Torsion and Annealing and Its Effects on Mechanical Properties

Microstructure and Texture Evolution of AZ31 Alloy Prepared by Cyclic Expansion Extrusion with Asymmetrical Extrusion Cavity at Different Temperatures

Evolution of Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Rolled Sheets During Annealing

Effect of Effective Strain Gradient on Texture and Mechanical Properties of Mg–3Al–1Zn Alloy Sheets Produced by Asymmetric Extrusion

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy