Abstract:Electrochemical electric double layer capacitors (EDLC) known as supercapacitors are used for high power density, long cycle life and good reversibility of charge/discharge processes[1]. Recent years, many Schiff base transition metal composites acting as an electroactive electrode material deposited on carbon nanotubes(CNTs) have been researched[2]. However, the CNTs tend to be random orientation, twining round and cross linked. So it urgently need to be addressed. In this paper, a given mass of NH4BF4 was added to CNTs and the electrode was prepared by the homodispersion of the raw support material in N-methyl- 2-pyrrolidone (NMP) through sonicating. The slurry was coated on a Ti sheet with the coating mass of 0.3 mg. The electropolymerization of Ni(salen) on the resulting electrode was conducted in a closed three-electrode compartment cell adopted chronoamperometry method. The introduction of NH4BF4 to the CNTs with a specific percentage (5wt. %, 10wt. %, 15 wt. %), and the modified samples were named as NBF5, NBF10, NBF15 respectively and the CNTs without NH4BF4 were taken as a control group and named as NBF0. As the cyclic voltammetric data summarized in Table 1, the values of apparent surface coverage(Γ) and doping level(n) of NBF5, NBF10 and NBF15 didn't appear to be much different from those of NBF0. However, the specific capacitance varied a lot. It can be seen that Cm of NBF15 is the most among the samples. Figure 1 depicts the GCD plots of the composite and CNTs at the current density of 1.0 mA cm-2. CNTs have symmetric change in the charge/discharge process which is the characteristic of high Coulombic efficiency. It is clear that the composites possess longer charge/discharge time than CNTs which indicating that poly[Ni(salen)] contributes the pseudo-capacitance derived from reversible redox switching between neutral and oxidative states on the basis of electric double-layer capacitance of MWCNTs. Because of the introduction of NBF, it became difficult for CNTs to twint together disorderly. And the morphylogy of the electrode support got homogeneous. NBF-containing carbon nanotube could provide basic sites, and consequently improved the deposition of polymer and enhance the performance of the electrode material. Acknowledgement This work is financially supported by the National Natural Science Foundation of China (No. 51372021). References [1] D. Kaufman, K.L. Hudson, R. Mcclamrock. Science. 343 (2014) 1210–1211. [2] Y. Zhang, J. Li, F. Gao, F. Kang, X. Wang, F. Ye, J. Yang. Electrochim. Acta. 76 (2012) 1–7. Figure 1

Ionic Liquid Coated Single-Walled Carbon Nanotube Buckypaper As Supercapacitor Electrode

Facile Synthesis of Exfoliated Co-Al LDH-carbon Nanotube Composites with High Performance As Supercapacitor Electrodes.

Active Carbon Wrapped Carbon Nanotube Buckypaper for the Electrode of Electrochemical Supercapacitors

Superior Capacitive Performance of Aligned Carbon Nanotubes in Ionic Liquids

The highly enhanced performance of lamellar WS2 nanosheet electrodes upon intercalation of single-walled carbon nanotubes for supercapacitors and lithium ions batteries.

Nitrogen, Boron and Fluorine Tri-Doped Carbon Nanotubes on Carbon Cloth As the Electrode Materials for Supercapacitors

Robust Single‐Walled Carbon Nanotube‐Infiltrated Carbon Fiber Electrodes for Structural Supercapacitors: from Reductive Dissolution to High Performance Devices

A three-dimensional carbon nanotube/graphene sandwich and its application as electrode in supercapacitors.

Single-walled carbon nanotube embedded porous carbon nanofiber with enhanced electrochemical capacitive performance

Mesoporous Carbon Nanofibers for Supercapacitor Application

Introduction of Bimetallic Oxide-Modified Carbon Nanotubes for Boosting the Energy Storage Performance of Nico-Ldh Based In-Plane Micro-Supercapacitors on Paper

Polytoluidine blue-coated multiwalled carbon nanotubes: In-situ polymerization based hybrid nanostructure for high performance asymmetric supercapacitors

The Electrochemical Performance of Nitrogen-Containing Carbon Nanotubes As the Electrode Material of Supercapacitors

Facile Fabrication of Nickel Aluminum Layered Double Hydroxide/Carbon Nanotube Electrodes Toward High-Performance Supercapacitors

Thin carbon nanotube coiled around thick branched carbon nanotube composite electrodes for high-performance and flexible supercapacitors

Enhancing supercapacitor performance using nanosheet-covered nanotube structures Co 3 S 4 /Ni 0.96 S@CNTs with carbon nanotubes as conductive substrates

High Performance Electrochemical Capacitors from Aligned Carbon Nanotube Electrodes and Ionic Liquid Electrolytes

Synthesis and characterization of modified centrifuged-electrospun carbon nanofibers for high-performance supercapacitor electrodes

Core-Double-Shell, Carbon Nanotube@Polypyrrole@MnO2 Sponge As Freestanding, Compressible Supercapacitor Electrode

Carboxylated multi-walled carbon nanotube/polyaniline composites for high-performance supercapacitor electrodes

Carbon Nanoparticle Ionic Liquid Functionalized Activated Carbon Hybrid Electrode for Efficiency Enhancement in Supercapacitors