Abstract:As a key component of a reversible pump-turbine unit, a pump-turbine runner rotates at two opposite directions under the pump and turbine modes. The flow states in the runner are quite different under the pump and turbine modes, which creates a great challenge for the design of a pump-turbine runner. Nowadays, a pump-turbine runner is always designed in one mode and verified with the other mode. Since there are several parameters affecting the runner’s performances and one parameter might have contrary effects on runner performances under the pump and turbine modes, it is hard to obtain a runner with high performance at both the pump and turbine modes by a trial and error method. In the present paper, a 3D inverse design method, CFD calculations, and multi-objective optimization strategy were coupled, and an optimal design system was built to improve the performances of a reversible pump-turbine runner. In the system, by using a 3D inverse design method, the runner shape was obtained by inputting corresponding parameters. A validated CFD method was used to estimate runner performances under different operating conditions. A multi-objective optimization strategy was then adopted to search runners with good performances at both operating modes in the design space based on a response surface model between input parameters and runner performances. The optimal design system was capable of solving some difficulties in pump-turbine runner design, such as a long design cycle and difficulties in obtaining good performances at both pump and turbine modes. The system was used to optimally design a middle-high head reversible pump-turbine runner, in which blade loading and blade lean were chosen as the input parameters, runner efficiency at the pump design point and the turbine rated point were set as optimization objectives, and the head at pump design point was set as a constraint. Since the optimization calculations were based on a response surface model, performances of nearly 10 000 runners under different operating modes were estimated in several minutes. Three runners from the Pareto frontier were chosen for detailed validation. CFD results showed that the optimal runner had a high hydraulic efficiency of over 95% at both the pump and turbine modes, which indicated a great improvement in runner efficiency in the turbine mode and the maintenance of high efficiency at the pump mode as compared with the initial design. The effects of the input parameters on runner interior characteristics under different operating modes were also analyzed in this paper. The results showed that fore-loaded blade loading distribution on the shroud was helpful in improving the flow state at the inlet under the pump mode by reducing the low-pressure area on the suction side. The blade lean at the high pressure side not only changed the work distribution along the span wise direction, but also improved the flow state by bringing down the pressure difference at the inlet in the turbine mode, and played an important role in improving runner efficiency, especially in the turbine mode.

Full 3-D Viscous Optimization Design Of A Reversible Pump Turbine Runner

Optimal design of reversible pump-turbine runner

Optimization Design of a Reversible Pump–turbine Runner with High Efficiency and Stability

Development Of A Pump-Turbine Runner Based On Multiobjective Optimization

Multiobjective optimization design of ultrahigh-head pump turbine runners with splitter blades

Three-dimensional Reverse Design Method for Pump-Turbine Runners

Optimum Design of Pump-Turbine for Bidirectional Flow Control

Parametric design and multi-objective optimization on blade high-pressure side of a pump-turbine

Research and optimization of performances of a pump turbine in pump mode

Design Optimization of Axial Flow Hydraulic Turbine Runner: Part II—multi‐objective Constrained Optimization Method

Design Optimization of Axial Flow Hydraulic Turbine Runner: Part I—an Improved Q3D Inverse Method

3-D TWO-WAY NUMERICAL SIMULATION AND PERFORMANCE ESTIMATION ON THE WHOLE FLOW PASSAGE OF THE REVERSIBLE PUMP-TURBINE RUNNER

Centrifugal Pump Blade Optimization Based on a Combined Optimization Strategy

Blade Design with Three-Dimensional Viscous Analysis and Hybrid Optimization Approach

Multidisciplinary design optimization on the splitter blade of high head Francis turbine

Bidirectional Flow Diagnosis to Optimize the Design of a Pump-Turbine Runner Using Vorticity Dynamics Theory

Research on a Full Three-Dimenional Inverse Method for the Mixed-Flow Pump Runner

Hydraulic development of high specific-speed pump-turbines by means of an inverse design method, numerical flow-simulation (CFD) and model testing

Strategies employed in the design and optimization of pump as turbine runner

Coupled design and optimization for runner blades of a tubular turbine based on the boundary vorticity dynamics theory

Three-dimensional Coupled Design for Runner Blades and Guide Vanes of Tubular Turbine Based on Bidirectional Flow Control