Abstract:Selective laser melting (SLM) technology was employed for the additive manufacturing of Ti-5Al-2.5Sn alpha titanium alloy in this work and the influences of laser energy input on densification behavior, microstructure evolution and mechanical performances of the as-deposited products were investigated. It was found that the relatively high volumetric energy densities (VEDs) of 167-417 J/mm(3) resulted in large quantities of keyhole-induced spherical pores whereas the relatively low VEDs of 51-83 J/mm(3) led to notable lack-of-fusion defects. At the proper VED of 125 J/mm(3), highly densifled products with internal porosity of merely 0.05% were obtained. At the relatively high VEDs of 167-417 J/mm(3), as-built samples presented duplex microstructures composed of acicular alpha' martensites and bulk alpha(M) massive grains. In contrast, overwhelmingly martensitic microstructures were formed at lower VEDs of 51-125 J/mm(3). The martensitic microstructure exhibited a unique hierarchical feature, which could be explained using the theory of athermal martensitic transformation kinetics. With the decrease of VED from 417 J/mm(3), the average size of alpha' needles increased first, then came to its plateau at the VEDs of 167-208 J/mm(3), and decreased again at the VEDs of 51-167 J/mm(3). At the VEDs of 167-417 J/mm(3), the formation of spherical pores and bulk alpha(M) grains resulted in relatively poor tensile properties. At the VEDs of 51-83 J/mm(3), the formation of lack-of-fusion defects masked the enhanced fine-grain strengthening effect provided by the much refined alpha' needles and the decrease in the fraction of bulk alpha(M), thus also leading to very limited tensile properties. At the proper VED of 125 J/mm(3), as-built tensile properties reached to their peak with ultimate tensile strength of 1173 MPa, yield strength of 1061 MPa, and elongation of 7.7%. This can be attributed to the high densification degree, the almost complete vanish of bulk alpha(M) grains, and the moderate size of alpha' needles. (C) 2018 Elsevier B.V. All rights reserved.

Selective Laser Melting Bone-Compatible Pure Titanium Porous Structure

Mechanical Properties of Optimized Diamond Lattice Structure for Bone Scaffolds Fabricated via Selective Laser Melting

Fabrication and Mechanical Properties of Porous Cp-Tiusing Selective Laser Melting (Slm)

Quality assurance thermophysical aspects of highly porous implants with cellular structure obtained by selective laser melting

Optimization of Structural and Processing Parameters for Selective Laser Melting of Porous 316L Bone Scaffolds

Compressive properties and deformation mechanism of selective laser melting of Ti6Al4V porous femoral implants based on topological optimization

An Integrated Approach of Topology Optimized Design and Selective Laser Melting Process for Titanium Implants Materials.

Tailored mechanical response and mass transport characteristic of selective laser melted porous metallic biomaterials for bone scaffolds

Anisotropy of Body-Centered-Cubic Porous Structures by Selective Laser Melting

Porous structure design and properties of dental implants

Fabrication of Customized Ti6AI4V Heterogeneous Scaffolds with Selective Laser Melting: Optimization of the Architecture for Orthopedic Implant Applications.

Mechanical Properties and Biocompatibilities of Radially Graded Porous Titanium/Tantalum Fabricated by Selective Laser Melting

Experimental Study of Performance of Ti-6Al-4V Femoral Implants Using Selective Laser Melting (SLM) Methodology

Densification Behavior, Microstructure Evolution, and Mechanical Performances of Selective Laser Melted Ti-5Al-2.5Sn Α Titanium Alloy: Effect of Laser Energy Input

Structural Optimization Design and Compression Performance of Porous Titanium Prepared by Laser Powder Bed Fusion

Laser beam melting 3D printing of Ti6Al4V based porous structured dental implants: fabrication, biocompatibility analysis and photoelastic study

Structural Characteristics And Mechanical Behavior Of Selective Laser Sintered Porous Ti-6mo Alloy For Biomedical Applications

Compressive properties and energy absorption of selective laser melting formed Ti-6Al-4V porous radial gradient scaffold

Fabrication of Porous Bioactive Structures Using the Selective Laser Sintering Technique

Structure Optimization of Porous Dental Implant Based on 3D Printing

Microstructure and Biomechanical Properties in Selective Laser Melting of Porous Metal Implants.