Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. In this article, Aluminum (Al2219) as a matrix, and particles of n-B4C and MoS2 were chosen as reinforcements. By means of the stir casting technique, the unhybrid and hybrid nano metal matrix composites were prepared. The turning experiment was done through CCD design of experiment with TiN coated carbide insert using a Computer Numerically Controlled Lathe. Also, for turned inserts tool wear measurement was done using a Mitutoyo profile projector with digital readout. By ANOVA the significant contribution for tool wear of each parameter can be identified and the confirmation test is performed in sort to validate the tool wear results. Furthermore, the formation of chips during turning nano MMCs (unhybrid and hybrid) are studied for different feed rates (f) and cutting speeds (v) at 0.5 mm constant depth of cut. The outcome showed that both increases in cutting speed and feed rate increase the tool wear. For Al 2219, unhybrid and hybrid nano metal matrix composites feed rate is the important factor. The value of tool wear of the Al2219 matrix is minimal and for unhybrid nano composite is maximum. The leading wear mechanism in unhybrid nano composite is abrasion. Moreover, with the addition of 2%MoS2 in the hybrid nanocomposite the tool wears is decreased. The development of Build Up Edge (BUE) was seen on the flank face of the cutting tool for hybrid nanocomposite at 0.5 mm depth of cut, (v = 114.64 m/min) and (f = 0.441 mm/rev). The obtained % error among the modeled and experimental values is <5% and it is well within the limit. The analysis of chip formation was studied for nanocomposites at lower as well as higher feed rates, cutting speeds, and constant depth of cut during turning.

Experimental Study On Performance Of Cbn-Coated, Cbn-Uncoated And Pcd Tools In Turning Al 2124 Sic (45%Wt) Pmmc

The Study on the Effect of Various Tool Wear Indicators on the Machining of MMCs

Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling

Evaluation of tool wear when machining SiCp-reinforced Al-2014 alloy matrix composites

Wear performance and mechanisms of PCBN tools in boring of powder metallurgy steels

Study on tool wear of cemented carbide coated tool in milling of SiCp/Al composites

Cutting performance and tool wear mechanism of corrugated helical PCD tool in milling Cf/SiC composites

Study of cutting force and tool wear during turning of aluminium with WC, PCD and HFCVD coated MCD tools

An experimental approach to characterize the performance of PCD and PCBN tools in milling nano Al-8081-Zr/Mg/TiO2 metal matrix composites using multi-sensor data fusion

Study on tool wears in turning Al2219, unhybrid and hybrid metal matrix nano composites by CCD design of experiment

Cutting performance and wear behavior of diamond, coated cemented carbide and PCBN tools during milling of C f /SiC composites

Research on Tool Wear in Machining of Particle Reinforced Aluminium Metal Matrix Composites Using PCD Tool

Cutting performance of cubic boron nitride-coated tools in dry turning of hardened ductile iron

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Performance Assessment of Pcbn and Bcbn Tools in Machining of High-Chromium White Cast Iron

Comparison of tool life and surface characteristics of uncoated, coated carbide and ceramic tools during machining of SiC reinforced ZA43 alloy MMC

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Preparation of Micro-Pit-Textured PCD Tools and Micro-Turning Experiment on SiCp/Al Composites

Tool wear characteristics analysis of cBN cutting tools in high-speed turning of Inconel 718

Study on Tool Wear of High Volume Fraction SiCp/Al Composites with Ultrasonic Vibration High Speed Milling