Abstract:In this study, thin-wall Mg-6.03Zn-0.55Zr alloy tubes consisted of fine dynamic recrystallized (DRXed) grains and ultrafine grains were successfully obtained by hot spinning process. The results showed that the microstructures of the initial extruded tubes were greatly refined with average grain sizes of 4.46–10.32 µm (300–450 ℃) due to the DRX process, especially at low spinning temperatures. Moreover, the basal texture was transformed from extruded fiber texture to spun tilted plane texture with an angle of ∼10° deviated from the axial direction (AD). More specifically, the basal texture was weakened along AD but was strengthened along the transverse direction (TD) compared with the extruded texture due to the reduced difficulty in pyramidal <c+a> slip activation and the shear deformation induced by the rollers. Consequently, the spun Mg-6.03Zn-0.55Zr alloys showed significant yield asymmetry along AD and TD at room temperature and the increase in spinning temperature had a negative influence on yield strength (YS) that the YS along AD decreased from 290 ± 5 MPa (300 ℃) to 232 ± 2 MPa (450 ℃) and the YS along TD decreased from 236 ± 6 MPa (300 ℃) to 198 ± 4 MPa (450 ℃). Both texture and grain refinement were the important factors in the mechanical properties according to the Hall-Petch relationship due to the varied activation fractions of deformation modes along AD and TD, especially the activation of prismatic <a> slip. Moreover, the fracture mechanism of the spun alloys consisting of fine DRXed grains and ultrafine grains was unusual. The aggregated ultrafine grains played a negative role in the fracture mechanism, because the ultrafine grains were transformed from the dislocation cells and the micro-crack easily occurred in the ultrafine grains.

Study on the microstructure and texture of zirconium alloy tube

Texture Development of Ti-3Al-2.5V Titanium Alloy Tubes

The development of texture in zirconium alloy tubes

Texture Evolution and Mechanical Anisotropy of Cold-Rolled Zr-4 Alloy Tube after Recrystallization Annealing

Investigation on textures of the alloy Ti-2Al-2. 5Zr tube and sheet

Microstructure and Texture Characterstics of a Near-Alpha Titanium Alloy Tube

Influence of Lubrication Effect on Microstructure of Hot Extruded Nuclear Grade Zr-4 Alloy

Microstructure characteristics, yield asymmetry and fracture mechanism of the fine grained thin-wall Mg-6.03Zn-0.55Zr tubes fabricated by hot spinning

Microstructural and Textural Evolution of a Zr-Sn-Nb-Fe Alloy Tube During Cold Pilger Rolling

Texture and Twinning Evolution of Cold-Rolled Industrial Pure Zirconium

Microstructural Evolution of Ultra-Fine Grained Mg-6.62Zn-0.6Zr Alloy on the Basis of Adiabatic Rise in Temperature under Dynamic Loading

Effect of Yttrium on Microstructures and Properties at Elevated Temperature of Mg-0.8Zr-0.35Zn Alloys

Regularities of Changes in the Structure of Different Phases of Deformed Zirconium Alloys as a Result of Raising the Annealing Temperature According to Texture Analysis Data

Effect of Heat Treatment on Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Tube

Deformed Microstructure and Texture of Ti6Al4V Alloy

Effect of zirconium addition on microstructure and mechanical properties of Mg97Y2Zn1 alloy

Evolution of microstructure and texture of AZ80 magnesium alloy under hot torsion with constant decreasing temperature rate

Recrystallization and texture evolution of warm-pilgered FeCrAl alloy tube during annealing at 850°C

Microstructure evolution and its effect on the impact toughness of the Ti-Al-V-Mo-Zr alloy tube

High Strain Rate Deformation Behavior of Zirconium at Elevated Temperatures

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments