Abstract:Superlubricity may be the ideal and final solution for friction and wear. Superlubricity on a micrometer scale based on an excellent self-retraction phenomenon has been observed and realized under ambient conditions recently. But not all of the graphite interfaces can realize superlubricity even they are incommensurate. Therefore, in-depth studies of graphite interfaces are needed to find out the factors which prevent the superlubricity for being realized. For this reason, microscopic graphite mesas are fabricated on a highly oriented pyrolytic graphite in this paper to obtain superlubricity interfaces. After poor quality graphite layers are mechanically exfoliated from the highly oriented pyrolytic graphite, a silicon dioxide film is grown on a new graphite surface by plasma-enhanced chemical vapor deposition. Then the film is coated with photoresist. Microscopic photoresist square pattern is defined by electron beam lithography and used as a mask for reactive ion etching the SiO2 and highly oriented pyrolytic graphite to define graphite mesas. The graphite interfaces are obtained by shearing the graphite mesas by tungsten tips. Some of them are super lubricative, while others are not. To study the graphite interfaces, atomic force microscope is used to characterize the morphologies of graphite mesas. The edges of graphite contact surfaces are also tested by energy dispersive spectrometer (EDS) and X ray photoelectron spectroscopy (XPS). The morphologies of the four graphite surfaces show that the superlubricity surfaces are atomically flat while other surfaces have many defects such as steps and tears. These results are consistent with those from the“stone wall” model of graphite crystal structure. The results of EDS and XPS show that there are many oxygen-containing bonds at the edges of the graphite surfaces. It is found that the polycrystalline structure of the highly oriented pyrolytic graphite plays an important role in the forming process of graphite interface and can affect the quality of the graphite interface. The quality of the graphite surface will determine whether the superlubricity can be realized. Besides the inner of graphite interface, the edges of the interfaces can also hinder the superlubricity from being realized. There are a large number of induced chemical bonds and the adsorbed physical bonds adhered to the edge of the graphite contact surfaces. When these bonds are broken, the energy is required. These bonds are the origin of the resistance when the graphite mesa is sheared away from the contact surface and causes friction force when the contact surface is relatively sliding along the other contact surface even the interface is super lubricative. The results show that the polycrystalline structure of the highly oriented pyrolytic graphite can affect the quality of the graphite interface and determine whether the superlubricity can be realized. For the destruction of bonds sticking at the interface edge requires energy, the edge of the contact surface can cause the friction force of superlubricity. It is indicated that increasing the sizes of the graphite grains is beneficial to the realization of large area superlubricity. Using high temperature annealing or other methods to reduce the adsorbed bonds of the graphite edges will also reduce the frictional resistance in the process of superlubricity.

Anisotropic Friction Behaviour of Highly Oriented Pyrolytic Graphite

Anisotropic Friction Behavior of Aligned and Oriented Graphite Flakes/copper Composite

Anisotropic Friction Derived from the Layered Arrangement of the Oriented Graphite Flakes in the Copper–Iron Matrix Composite

An Investigation on the Friction of Oriented Polytetrafluoroethylene (PTFE)

Characterization and Analysis of Microscale Sup Erlubricity Graphite Surface

Achieving Controllable Friction of Ultrafine-Grained Graphite HPG510 by Tailoring the Interfacial Nanostructures

Temperature-dependent Friction Coefficient on Flat Graphite Plane

Research on Spectral Characterization of Superlubricity Graphite Surface

Effect of Surface Topography on Anisotropic Friction of Graphene Layers

Effect of the graphite domain direction on the friction coefficient of tetrahedral amorphous carbon nitride

Environmental Molecular Effect on the Macroscale Friction Behaviors of Graphene

Directional Anisotropy of Friction in Microscale Superlubric Graphite/ Hbn Heterojunctions

Towards a deeper understanding of superlubricity on graphite governed by interfacial adhesion

Temperature and Velocity Dependent Friction of a Microscale Graphite-Dlc Heterostructure

Is Ultralow Friction on Graphite Sustainable in Contaminated Environments?

Micro-friction behavior of amorphous carbon films on porous AAO membrane synthesized by the pyrolysis of polyethleneglycol 400

Characterization of a Microscale Superlubric Graphite Interface

The influence of roughness on tribological properties of nuclear grade graphite

Positive-Negative Tunable Coefficients of Friction in Superlubric Contacts

Robust Microscale Structural Superlubricity Between Graphite and Nanostructured Surface

Relationship between Friction Properties and Friction Surface Status of C/C Composites