Abstract:The recently developed tough and self-healing hydrogels, containing a large number of physical bonds, have found widespread applications in bioengineering and soft electronics. Owing to the sophisticated physical interactions and organization, these hydrogels often demonstrate structural heterogeneities, which strongly influence their mechanical performances. Using poly(N,N-dimethyl acrylamide-co-methacrylic acid) hydrogels (P(DMAA-co-MAAc)) with dynamic hydrogen bonds (H-bonds) as a model system, the structural characterization has been carried out in this study using small-angle X-ray scattering (SAXS) and small-angle neutron scattering (SANS) analyses, along with exploring the influence of the structure on the mechanical properties. By systematically tuning the polymer composition, including the monomer fraction and chemical cross-linking density, two different hydrogel regions with distinct mechanical properties were observed: the swollen regions and shrunk regions. The former was mechanically weak, whereas the latter exhibited a tough behavior. Both types of hydrogels were noted to be highly heterogeneous, which results from the nanoscale spatial polymer concentration fluctuations at ∼100 nm scale. Combined with the contrast variation utilizing SANS, the structure parameters, including the polymer volume fraction of the dense and sparse regions, volume fraction occupied in the space, and average correlation length of the long-range and short-range heterogeneous structures, were explored using a scaling model based on a two-phase system composed of the densely and sparsely cross-linked regions. Using in situ SAXS, the microscopic deformation of the tough and shrunk hydrogels was noted to follow the affine deformation, while a significantly non-affine deformation was observed in the swollen hydrogels, which might have led to the different mechanical performances of these materials.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.macromol.1c01064.Swelling volume ratio of hydrogels 0.14-0.2% during the drying–swelling cycle (Figure S1); FT-IR spectra of PDMAA, PMAAc, and P(DMAA-co-MAAc) and temperature dependence of FT-IR spectrum of P(DMAA-co-MAAc) (Figure S2); semi-empirical quantum chemical calculations for revealing the conformation features and their interaction in water (Figure S3); tensile stress–strain curves of P(DMAA-co-MAAc) hydrogels f-0.1% with various f values (0.12, 0.13, and 0.15) and P(DMAA-co-MAAc) hydrogels 0.14-x with various x values (0.05, 0.1, and 0.15%) (Figure S4); 1D scattering intensity as a function of the scattering vector q under various stretch ratios for the hydrogels f-0.1% with the molar fraction of DMAA varying from 0.12 to 0.15 and hydrogels 0.14-x with the chemical cross-linking density ranging from 0.05 to 0.15% (Figures S5 and S6); stretch-induced structure evolution of the swollen hydrogel 0.14-0 (Figure S7); tensile stress–strain curve of hydrogel 0.14-1% and the corresponding Mooney–Rivlin plot (Figure S8); and structural parameters of the swollen and shrunk hydrogels (Table S1) (PDF)This article has not yet been cited by other publications.

Anisotropic Tough Poly(2-Hydroxyethyl Methacrylate) Hydrogels Fabricated by Directional Freezing Redox Polymerization

Anisotropic hydrogels fabricated with directional freezing and radiation-induced polymerization and crosslinking method

Anisotropic Tough Poly(vinyl Alcohol) Hydrogels

Sculpting Mechanical Properties of Hydrogels by Patterning Seamlessly Interlocked Stiff Skeleton

Strong and Ultra-Tough Supramolecular Hydrogel Enabled by Strain-Induced Microphase Separation

Anisotropic Hydrogel from Complexation-Driven Reorientation of Semirigid Polyanion at Ca2+ Diffusion Flux Front

Freezing Molecular Orientation under Stretch for High Mechanical Strength but Anisotropic Hydrogels.

Tough Hydrogels with Isotropic and Unprecedented Crack Propagation Resistance

Strong, tough and anisotropic bioinspired hydrogels

Dry-regulated hydrogels with anisotropic mechanical performance and ionic conductivity

Tuning structural and mechanical anisotropy of PVA hydrogels

Toughening Hydrogels by Immersing with Oppositely Charged Polymers

Tough and super-resilient hydrogels synthesized by using peroxidized polymer chains as polyfunctional initiating and cross-linking centers

A Facile Method To Fabricate Tough Hydrogel With Ultra-Wide Adjustable Stiffness, Stress, And Fast Recoverability

Anisotropic Hydrogels with Enhanced Mechanical and Tribological Performance by Magnetically Oriented Nanohybrids

Hierarchical networks of anisotropic hydrogels based on cross-linked Poly(vinyl alcohol)/Poly(vinylpyrrolidone)

Strong tough hydrogels via the synergy of freeze-casting and salting out

3D-Printed Hydrogels with High-Strength and Anisotropy Mediated by Chain Rigidity

Tough Hydrogels with Dynamic H-Bonds: Structural Heterogeneities and Mechanical Performances

Plastic-Like Supramolecular Hydrogels with Polyelectrolyte/Surfactant Complexes as Physical Cross-links

Mechanically Tough and Recoverable Hydrogels Via Dual Physical Crosslinkings