Abstract:Poly (lactic acid) (PLA)-Poly (propylene carbonate) (PPC) block copolymer compatibilizers are produced in incompatible 70wt%PLA/PPC blend by initiating transesterification with addition of 1% of tetra butyl titanate (TBT) or by chain extension with addition of 2% of 2,4-toluene diisocyanate (TDI). The above blends can have much better mechanical properties than the blend without TBT and TDI. The elongation at break is dramatically larger (114% with 2% of TDI and 60% with 1% of TBT) than the blend without TDI and TBT, with a slightly lower mechanical strength. A small fraction of the copolymer is likely formed in the PLA/PPC blend with addition of TBT, and a significant amount of the copolymer can be made with addition of TDI. The copolymer produced with TDI has PPC as a major content (~70 wt%) and forms a miscible interphase with its own Tg. The crystallinity of the blend with TDI is significantly lower than the blend without TDI, as the PLA blocks of the copolymer in the interphase is hardly to crystallize. The average molecular weight increases significantly with addition of TDI, likely compensating the lower mechanical strength due to lower crystallinity. Material degradation can occur with addition of TBT, but it is very limited with 1% of TBT. However, compared with the blends without TBT, the PLA crystallinity of the blend with 1%TBT increases sharply during the cooling process, which likely compensates the loss of mechanical strength due to the slightly material degradation. The added TDI does not have any significant impact on PLA lamellar packing, but the addition of TBT can make PLA lamellar packing much less ordered, presumably resulted from much smaller PPC domains formed in the blend due to better compatibility.

Orientation microstructure and properties of poly(propylene carbonate)/poly(butylene succinate) blend films

Synthesis and Thermomechanical and Rheological Properties of Biodegradable Long-Chain Branched Poly(Butylene Succinate-Co-Butylene Terephthalate) Copolyesters

The Morphology and Mechanical Properties of the Hybrid Films of Styrene-Butyl Acrylate Block Copolymer/Mmt from Colloid Blending

Deformation and Molecular Orientation in Films of Metallocene Polypropylene, Ethylene-Butylene Rubber, and Their 80/20 (W/W) Blend Revealed by the Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism, Macroscopic Stress, and Mesoscale Strain

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Interfacial Interaction Analysis of Blends of Poly(vinylidene Fluoride) and Poly(ethylene–butylacrylate–glycidyl Methacrylate) Compatibilized by Poly(butylene Succinate): Morphologies, Rheological Behavior, and Mechanical Properties

Fully Biodegradable Blends of Poly(butylene Succinate) and Poly(butylene Carbonate): Miscibility, Thermal Properties, Crystallization Behavior and Mechanical Properties

Structure of PBAT/PPC blends prepared by in-situ reactive compatibilization and properties of their blowing films

High Content of Thermoplastic Starch, Poly(butylenes Adipate-Co-terephthalate) and Poly(butylene Succinate) Ternary Blends with a Good Balance in Strength and Toughness.

Preparation and Characterization of Poly(butylene Succinate-Co-adipate)/poly(lactic Acid) Blends with Enhanced Compatibility, Mechanical Properties, and Heat Resistance

Blends of Poly(β-hydroxybutyrate) with Poly(propylene carbonate)

Blends of Polypropylene and Syndiotactic 1,2-Polybutadiene: Morphology, Crystallization Behaviors and Mechanical Properties

Research on Poly(lactic acid)/Poly(butylenes succinate) Blends

Enhanced Impact Resistance, Oxygen Barrier, and Thermal Dimensional Stability of Biaxially Processed Miscible Poly(Lactic Acid)/Poly(Butylene Succinate) Thin Films

Crystallization and phase behavior of crystalline syndiotactic 1,2-polybutadiene/isotactic polypropylene blends in solution-cast thin films

Effect of Styrene-Maleic Anhydride Copolymer on Properties of PBST/PLA Blends

A study on the mechanical, thermal properties and crystallization behavior of poly(lactic acid)/thermoplastic poly(propylene carbonate) polyurethane blends

Enhancement of the Compatibility, Mechanical Properties, and Heat Resistance of Poly(butylene Succinate-Co-terephthalate)/poly(butylene Succinate) Blends by the Addition of Chain Extender and Nucleating Agent

Crystallization, Structure and Significantly Improved Mechanical Properties of PLA/PPC Blends Compatibilized with PLA-PPC Copolymers Produced by Reactions Initiated with TBT or TDI

Property Study on PHBV/PBS Blends

Reinforcing and Toughening Modification of PPC/PBS Blends Compatibilized with Epoxy Terminated Hyperbranched Polymers