Abstract:Flow chart of CNF adsorption by graphene oxide. Cellulose fibers were modified via aqueous silane‐graphene oxide (GO) coordination by flash drying and extrusion dispersion process. The adsorption of GO reduced the polarity of the cellulose fiber surface and attenuated the agglomeration effect between the cellulose fibers, thus facilitating the dispersion of fibers in the rubber matrix. Adding aqueous 3‐aminopropylsilane oligomer (8150) incorporated active sites on the surface of cellulose fibers, thereby improving the interfacial binding properties of cellulose nano fibers (CNFs) and natural rubber (NR). After blending the modified CNFs with NR latex, high‐temperature flocculation was performed using an atomised flash device. Finally, CNF/NR was pre‐dispersed through a twin‐screw extruder, after which a CNF/NR masterbatch with excellent performance was prepared. Experimental results revealed that composites prepared using GO‐8150 via the flash drying‐twin‐screw dispersion process exhibited excellent dispersion characteristics, processing properties, mechanical properties, rolling resistance, wear resistance, and heat generation properties. Compared with traditional dry mixing, the composites prepared by flash drying‐twin‐screw dispersion process showed a 16.95% increase in tensile strength, 16.07% increase in 300% constant elongation, 19.01% reduction in abrasion consumption, 42.26% reduction in rolling resistance, and a reduction in the Payne effect. This study offers an efficient and environmentally friendly method for the high‐value utilization of natural fibers and the preparation of NR composites with excellent properties, while providing a green and nonpolluting modification process with no acidic liquid discharge. Highlights GO‐8150 reduces the polarity of the fibers and promotes dispersion. The flash extrusion dispersion process achieves green flocculation. 42% lower rolling resistance for rubber composites.

Compatibilization Of Natural Rubber/High Density Polyethylene Thermoplastic Vulcanizate With Graphene Oxide Through Ultrasonically Assisted Latex Mixing

Promoting compatibilization effect of graphene oxide on immiscible PS/PVDF blend via water-assisted mixing extrusion

Enhanced Compatibility and Mechanical Properties of Carboxylated Acrylonitrile Butadiene Rubber/Styrene Butadiene Rubber by Using Graphene Oxide As Reinforcing Filler

Compatibilizing Effect of Graphene Oxide on Polyamide 6/polystyrene Blends

Synthesis of a novel reactive compatibilizer with large surface area and the application in monomer casting nylon/polyethylene–octene elastomer blends

Simultaneous Reduction And Surface Functionalization Of Graphene Oxide And The Application For Rubber Composites

Preparation of Butadiene–styrene–vinyl Pyridine Rubber–graphene Oxide Hybrids Through Co-Coagulation Process and in Situ Interface Tailoring

A Slurry Compounding Route to Disperse Graphene Oxide in Rubber

Dispersion and exfoliation of graphene in rubber by an ultrasonically- assisted latex mixing and in situ reduction process

Impact Of Blend Ratio On The Properties Of Graphene Oxide-Filled Carboxylated Acrylonitrile-Butadiene Rubber/Styrene-Butadiene Rubber Blends

Temperature-dependent compatibilizing effect of graphene oxide as a compatibilizer for immiscible polymer blends

Preparation of Well-Dispersed Graphene Oxide-Silica Nanohybrids/poly (lactic Acid) Composites by Melt Mixing

Multifunctional Nanocomposites Between Natural Rubber and Polyvinyl Pyrrolidone Modified Graphene

Preparation and Characterization of Grafted Natural Rubber/Graphene Oxide Nanocomposites

Using a Green Method to Develop Graphene Oxide/elastomers Nanocomposites with Combination of High Barrier and Mechanical Performance

Reinforcement of Hydrogenated Carboxylated Nitrile–butadiene Rubber with Exfoliated Graphene Oxide

Preparation of aqueous silane‐graphene oxide co‐modified cellulose fibers/natural rubber composites via flash extrusion dispersion process

Polyolefin-functionalized graphene oxide and its GO/HDPE nanocomposite with excellent mechanical properties

Improved mechanical performance and swelling resistance of ethylene propylene diene monomer/styrene butadiene rubber nanocomposites through the incorporation of graphene oxide as a reinforcing filler

Probing the Reinforcing Mechanism of Graphene and Graphene Oxide in Natural Rubber

Synthesis of Polypropylene- Grafted Graphene and Its Compatibilization Effect on Polypropylene/ Polystyrene Blends