Abstract:A novel method for calculating the critical resolved shear stress (CRSS) ratios of different deformation system types in polycrystalline non-cubic metals has been developed. The mean CRSS ratios between different deformation systems were calculated for both commercially pure (CP) Ti and Ti–5Al–2.5Sn (wt.%) tensile deformed at ambient temperature and 455°C using an in situ scanning electron microscope-based testing technique combined with electron backscattered diffraction. It was found that the relative activity of the different deformation systems changes as a function of alloying composition and deformation temperature. Prismatic slip was the most active deformation mode for CP Ti. CP Ti exhibited a lower resistance to prismatic slip at both ambient and elevated temperatures compared with Ti–5Al–2.5Sn. For Ti–5Al–2.5Sn, prismatic slip was the most active deformation system at ambient temperature although the basal slip activity significantly increased compared to CP Ti, mostly likely due to an increased c/a ratio resulting in a closer packed basal plane. At 455°C, basal slip exhibited a lower CRSS than prismatic slip for Ti–5Al–2.5Sn. The relative activity of other deformation systems was also affected by alloying and temperature. The statistical resampling technique of bootstrapping was used to generate multiple equivalent data sets from which mean CRSS ratios between different deformation systems, and associated confidence intervals, could be deduced. It was found that the mean CRSS ratios at low and high strains varied slightly for the same testing conditions. Moreover, lesser activated slip systems resulted in relatively larger confidence intervals for the CRSS means. This variability may be attributed to a number of potential factors, including measurement errors, rotations of grains during deformation, local stress state variations, and work hardening. The analysis further suggests that awareness of the intrinsic statistical variability in CRSS ratios should be considered when formulating crystal plasticity constitutive models.

Estimation of critical resolved shear stress of single-phase polycrystallites based on crystallographic model

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Predicting Critical Conditions and Stress-Strain Curves for Dynamic Recrystallization in Sphc Steel

Methodology for estimating the critical resolved shear stress ratios of α-phase Ti using EBSD-based trace analysis

A new approach to the analysis of poly crystal plasticity

Analysis of Yield Strength Anisotropy of Pipeline Steel Based on Crystallographic Model

Mathematical Modeling of Critical Condition for Dynamic Recrystallization

A finite strain micromechanical-based constitutive model: Application to porous polycrystal

Strain Rate-Dependent Plastic Behavior of TWIP Steel Investigated by Crystal Plasticity Model

Determining Individual Phase Flow Properties in a Quench and Partitioning Steel with in Situ High-Energy X-Ray Diffraction and Multiphase Elasto-Plastic Self-Consistent Method

Analysis of deformation inhomogeneity and slip mode of TA15 titanium alloy sheets during the hot tensile process based on crystal plasticity model

A reexamination of high strength steel Q690 plasticity model

Determination of Shear Behavior and Constitutive Modeling of the 603 Steel over Wide Temperature and Strain Rate Ranges

Crystal plasticity modeling of grain boundary softening and fatigue in U75V pearlite steel under low strain conditions: A study of cyclic rolling contact fatigue

Overall Stress–strain Relationship of Cold Rolled Transformation Induced Plasticity Multiphase Steels

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

3D Crystal Plasticity Finite Element Modeling of the Tensile Deformation of Polycrystalline Ferritic Stainless Steel

Experimental and Numerical Study on Strain Path and Crystal Orientation Dependences of Phase Transformation Behaviors of QP1180 Steel

A Two-Step Approach to Predict Shear Band Development with Crystal Plasticity Finite Element Method (Cpfem)

Numerical Simulation on Sheet Metal Forming with Rate-Independent Polycrystalline Plasticity Fem

Finite Element Calculation of Polycrystalline Shear-Compression Specimens with Static Loading