Abstract:Numerous combustion strategies have been suggested for compression ignition engines in order to meet the stringent emission regulations with minimal sacrifice in the fuel economy. Premixed charge compression ignition combustion has the potential to reduce the nitrogen oxide emissions and the soot emissions while maintaining a high thermal efficiency and has become the research focus recently. Experiments and simulations were used to study the effects of the injection mode and the injection timing on the premixed charge compression ignition combustion and the emissions in a heavy-duty diesel engine at low and medium loads. The results reveal the following. At low loads, when the injection timing of a single injection is 35° crank angle before top dead centre because of the impinging position of the spray, the mixture is divided into two parts: the fuel above the chamber and the fuel in the piston bowl. This helps to utilize fully the in-cylinder air to form a homogeneous mixture. Also the nitrogen oxide emissions are the lowest. At medium loads, with a single injection, the injection mass is increased, the injection duration is prolonged and the mixing timing is reduced. As a result, the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions are increased dramatically; the best emissions are gained at an injection timing of 35° crank angle before top dead centre owing to the combined effect of the optimized mixing time and the optimized mixing space. At medium loads, with multiple injections, the injection mass is divided into four pulses, the mixing timings of which are all increased. The mixing space of the fuel–air mixture is also improved, and a more homogeneous mixture is obtained, which is beneficial to decreasing the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions in comparison with those for the single-injection case. When the injection timings of multiple injections are 80° crank angle before top dead centre, 65° crank angle before top dead centre, 50° crank angle before top dead centre and 35° crank angle before top dead centre, the best trade-off between the performance and the emissions can be achieved at medium loads.

Effects of Structure of Combustion Chamber and Injector on Heavy-duty Diesel Performance and Emission Characteristics

Study on Emission Performance Test and Structure Parameter Optimization for Diesel Engine Equipped with EGR System

Simulation Study on Effects of Combustion Chamber Structure on Diesel Engine Combustion and its Adaptability to Boundary

Performance and Emission Characteristics of HD Diesel Using EGR Under Low-Speed and High-Load Conditions

Experimental Study of the Influence of Multi-Injection Coupled with EGR on Diesel Performance and Emissions

Experimental study of multiple injections and coupling effects of multi-injection and EGR in a HD diesel engine

Experimental study of multiple injections on a HD diesel engine

Effects of the Injection Parameters on the Premixed Charge Compression Ignition Combustion and the Emissions in A Heavy-Duty Diesel Engine

Effect of pre-chamber fuel injection parameters and EGR on the combustion and emissions of a heavy-duty diesel engine

Development of Combustion System of a Low-Emission Heavy-Duty Diesel Engine with EGR

Numerical Investigation on Effects of Assigned EGR Stratification on a Heavy Duty Diesel Engine with Two-Stage Fuel Injection

Study of Pilot Injection for the Improvement of Combustion and Emissions Characteristics in A Heavy-Duty Diesel Engine

Effect of Injector Improvement on Emissions from Diesel Engine with Spherical Combustion Chamber

Effects of injection strategy and combustion chamber modification on a single-cylinder diesel engine

Effect of Common Rail System on Vehicle Engine Combustion Performance

Experimental Study of Combustion Geometry on Combustion and Emissions of Diesel Engine

Effects of Key Parameters of Pre-Chamber on Engine Combustion and Emissions

Study on the Effects of Exhaust Gas Recirculation and Fuel Injection Strategy on Transient Process Performance of Diesel Engines

An Experimental Investigation of the Effects of Fuel Injection Strategy on the Efficiency and Emissions of a Heavy-Duty Engine at High Load with Gasoline Compression Ignition

Experimental and Numerical Study the Effect of EGR Strategies on In-Cylinder Flow, Combustion and Emissions Characteristics in a Heavy-Duty Higher CR Lean-Burn NGSI Engine Coupled with Detail Combustion Mechanism

Experimental Study on Effects of RCSL and RCTL Combustion Chamber for Combustion Process of Highly Intensified Diesel Engine