Abstract:The acidic, corrosive effect of sodium polystyrene sulfonate (PSS) in poly 3,4-ethylenedioxythiophene:sodium polystyrene sulfonate (PEDOT:PSS) limits the stability of inverted perovskite solar cells (PSCs) based on the ITO/PEDOT:PSS/perovskite/PCBM/BCP/Ag structure. In this work, a poly 3,4-ethylenedioxythiophene (PEDOT) hole transport layer (HTL) with high hole mobility and good catalytic performance was prepared by electrochemical cyclic voltammetry (CV) method for inverted PSCs. By controlling the CV cycles (from 1 to 5 cycles) and EDOT monomer solution concentration (from 0.5 to 2.0 mmol·L−1) of electrochemical deposition, the thickness, morphology, optical and electrochemical properties of PEDOT could be accurately adjusted. The optimal photovoltaic performance with current density (Jsc) of 22.19 mA·cm−2, open circuit voltage (Voc) of 0.94 V, fill factor (FF) of 0.65 and photoelectric conversion efficiency of 13.56% was obtained when deposition of PEDOT with 1 CV cycle and EDOT concentration of 0.5 mmol·L−1. At this point, the perovskite showed good crystallization, optimal optical, charge transport and recombination performance, resulting in better Voc and photoelectric conversion efficiency (PCE) compared to the devices with higher CV cycle numbers and 3,4-ethylenedioxythiophene (EDOT) concentration. For comparison with spin-coated PEDOT:PSS, the device with electrodeposited PEDOT showed improved Jsc and comparable Voc, which may result from its better charge transport and catalytic ability. The device with spin-coated PEDOT:PSS showed photoelectric conversion efficiency of 12.25%, which was lower than that based on electrodeposited PEDOT (13.56%) with 1 CV cycles and 0.5 mmol·L−1 EDOT concentration. And the device with electrodeposited PEDOT as HTLs showed more excellent air stability. In ambient air ((32 ± 5) °C and RH: 70% ± 20%), it still maintained more than 80% of the initial photoelectric conversion efficiency after 1000 h. In comparison, the photoelectric conversion efficiency of the device with PEDOT:PSS decreased to 20% of the initial value after storage for 500 h. From this study, a facial and low-cost way to prepare PEDOT HTL with high performances that better than the traditional PEDOT:PSS has been explored, which is expected to eliminate the acidic, corrosive effect of PSS in PEDOT:PSS.

Indium Tin Oxide-Free Polymer Solar Cells Using A Pedot:Pss/Ag/Pedot:Pss Multilayer As A Transparent Anode

Sulfonate Poly(aryl Ether Sulfone)-Modified PEDOT:PSS As Hole Transport Layer and Transparent Electrode for High Performance Polymer Solar Cells

Conductivity Enhancement of PEDOT:PSS Film Via Sulfonic Acid Modification: Application As Transparent Electrode for ITO-free Polymer Solar Cells

Indium Tin Oxide-Free Inverted Polymer Solar Cells with Ultrathin Metal Transparent Electrodes

Laminated Polymer Solar Cells with PEDOT:PSS Film As Anode

High-efficiency ITO-free polymer solar cells using highly conductive PEDOT:PSS/surfactant bilayer transparent anodes

Flexible inverted polymer solar cells with an indium-free tri-layer cathode

PEDOT:PSS‐Free Polymer Non‐Fullerene Polymer Solar Cells with Efficiency up to 18.60% Employing a Binary‐Solvent‐Chlorinated ITO Anode

Liquid-Crystalline Ionic Liquids Modified Conductive Polymers As A Transparent Electrode For Indium-Free Polymer Solar Cells

Transparent Conductive Oxide-Free Perovskite Solar Cells with PEDOT:PSS As Transparent Electrode

Highly Efficient, ITO-Free Polymer Solar Cells Using Ultrathin Copper Film As Transparent Electrode

Efficient polymer solar cells based on poly(3-hexylthiophene):Indene-C 70 bisadduct with a MoO 3 buffer layer

Semi-transparent Polymer Solar Cells with All-Copper Nanowire Electrodes

Efficient Ni/Au Mesh Transparent Electrodes for ITO-Free Planar Perovskite Solar Cells.

Polymer solar cells using chlorinated indium tin oxide electrodes with high work function as the anode

Low Work-function Poly(3,4-ethylenedioxylenethiophene): Poly(styrene Sulfonate) As Electron-transport Layer for High-efficient and Stable Polymer Solar Cells.

High-Performance Inverted Polymer Solar Cells Based on Thin Copper Film

Electrodeposited Transparent PEDOT for Inverted Perovskite Solar Cells: Improved Charge Transport and Catalytic Performances

Investigation On Polymer Anode Design For Flexible Polymer Solar Cells

PEDOT:PSS‐Metal Oxide Composite Electrode with Regulated Wettability and Work Function for High‐Performance Inverted Perovskite Solar Cells

All-spin-coating vacuum-free processed semi-transparent inverted polymer solar cells with PEDOT:PSS anode and PAH-D interfacial layer