Abstract:Fluid viscosity is one of the key factors affecting the cavitation characteristics of the Helico-axial Multiphase Pump (HAMP). In this paper, fluids with viscosities of 24.46 mm2/s, 48.48 mm2/s, 60.70 mm2/s, and 120.0 mm2/s were investigated by numerical simulation. The Ansys Fluent software was employed to conduct the simulation. The mixture multiphase flow model and the RNG k-ε turbulence model were adopted. The Singhal cavitation model was employed to consider the effects of the non-condensable gas on cavitation. An experiment was carried out to validate the numerical method. The results showed that the Net Positive Suction Head-available (NPSHA) of the pump decreased as the fluid viscosity increased. Under the critical NPSHA condition, the NPSHA decreased from 5.11 m to 3.68 m as the fluid viscosity increased from 24.46 mm2/s to 120.0 mm2/s. This suggested that the cavitation performance of the pump was deteriorated under high fluid viscosity. The impeller passage area occupied by the vapor increased when the fluid viscosity increased. Nearly half of the flow passages were occupied by cavitation bubbles when the fluid viscosity increased to 120.0 mm2/s. The vapor volume fraction, both on the suction surface and pressure surface of the blade, increased with the fluid viscosity. The vapor on the suction surface was mainly distributed in the region with the streamwise between 0 and 0.36 when the fluid viscosity was 24.46 mm2/s; while the high vapor volume fraction range increased to the streamwise of 0.42 when the fluid viscosity increased to 120.0 mm2/s. The higher vapor volume fraction corresponded with the lower pressure. It was also found that the turbulent kinetic energy, both on the suction surface and pressure surface, increased with the fluid viscosity, which was the favorite for producing more cavitation bubbles. Furthermore, the maximum velocity area was mainly concentrated in the inlet area of the impeller. The velocity distribution in the impeller was basically the same with the viscosity of 24.46 mm2/s and 48.48 mm2/s. When the viscosity further increased to 60.70 mm2/s, the maximum velocity area in the impeller was relatively large. This study provides a reference for designing the HAMP.

Effects of Fluid Viscoelasticity on the Performance of an Axial Blood Pump Model

An Experimental Study of Newtonian and Non-Newtonian Flow Dynamics in an Axial Blood Pump Model.

Numerical Simulation for Hydrodynamics and Biocompatibility in an Axial Blood Pump

Effects of Non-Newtonian Fluid on Centrifugal Blood Pump Performance

An experimental performance comparison of Newtonian and non-Newtonian fluids on a centrifugal blood pump

Numerical Simulation and Comparative Analysis of Flow Field in Axial Blood Pumps

Evaluation of the Hemolysis and Fluid Dynamics of a Ventricular Assist Device under the Pulsatile Flow Condition

Effect of Temperature on the Drag Reduction Characteristics of Xanthan Gum in the Liquid Ring Vacuum Pump

A Novel Design of Spiral Groove Bearing in a Hydrodynamically Levitated Centrifugal Rotary Blood Pump.

The simulation of multiphase flow field in ventricular assist device and analysis of hemolytic capability

Effects of Splined Shaft Bending Rigidity on Cylinder Tilt Behaviour for High-Speed Electro-Hydrostatic Actuator Pumps

Research on fluid properties of the anxial flow blood pump based on CFD

COMPARISON AND EXPERIMENTAL VALIDATION OF TURBULENCE MODELS FOR AN AXIAL FLOW BLOOD PUMP

Effects of Non-Newtonian Models on Viscosity of Unsteady Aortic Blood Flow

Hydrodynamic and Hemolysis Analysis on Distance and Clearance Between Impeller and Diffuser of Axial Blood Pump

Comparative study of SGS models for simulating the flow in a centrifugal-pump impeller using single passage

Influence of Fluid Viscosity on Cavitation Characteristics of a Helico-Axial Multiphase Pump (HAMP)

Computational Fluid Dynamics Modeling and Hemolysis Analysis of Axial Blood Pumps with Various Impeller Structures

Numerical study on the performance of centrifugal blood pump with superhydrophobic surface

Influence of Fluid Food Viscosity on Internal Flow Characteristics of Conveying Pump

Numerical Simulations of a Centrifugal Pump With a Non-Newtonian Fluid: Influence on Performances of Different Rheological Modelling