Local Heating of Individual Droplets Using Photothermal Effects of Gold Nanorods

Zhiyong Li,Pan Wang,Limin Tong,Lei Zhang

DOI: https://doi.org/10.1364/acpc.2012.ath2a.7

2012-01-01

Abstract:We present an efficient method to locally heat individual microfluidic droplets using photothermal effects of gold nanorods. A nanoliter droplet was heated to over 80 oC under illumination of a 13.6 mW heating laser.

What problem does this paper attempt to address?

Gold nanorod-facilitated localized heating of droplets in microfluidic chips.

Zhiyong Li,Pan Wang,Limin Tong,Lei Zhang

DOI: https://doi.org/10.1364/OE.21.001281

IF: 3.8

2013-01-01

Optics Express

Abstract:A gold nanorod-facilitated optical heating method for droplets in microfluidic chips is reported. Individual and stream nanoliter level droplets containing gold nanorods are heated by a low power 808-nm-wavelength laser. Owing to the high photothermal conversion efficiency of gold nanorods, a droplet temperature of 95 degrees C is achieved by employing a 13.6 mW laser with good reproducibility. The heating and cooling times are 200 and 800 ms, respectively, which are attributed to the fast thermal-transfer rates of the droplets. By controlling the irradiation laser power, the temperature cycles for polymerase chain reaction are also demonstrated. (C)2013 Optical Society of America
Photothermal Intracellular Delivery Using Gold Nanodisk Arrays.

Chuanzhen Zhao,Tianxing Man,Xiaobin Xu,Qing Yang,Wenfei Liu,Steven J. Jonas,Michael A. Teitell,Pei-Yu Chiou,Paul S. Weiss

DOI: https://doi.org/10.1021/acsmaterialslett.0c00428

IF: 11.4

2020-01-01

ACS Materials Letters

Abstract:Local heating using pulsed laser-induced photothermal effects on plasmonic nanostructured substrates can be used for intracellular delivery applications. However, the fabrication of plasmonic nanostructured interfaces is hampered by complex nanomanufacturing schemes. Here, we demonstrate the fabrication of large-area plasmonic gold (Au) nanodisk arrays that enable photothermal intracellular delivery of biomolecular cargo at high efficiency. The Au nanodisks (350 nm in diameter) were fabricated using chemical lift-off lithography (CLL). Nanosecond laser pulses were used to excite the plasmonic nanostructures, thereby generating transient pores at the outer membranes of targeted cells that enable the delivery of biomolecules via diffusion. Delivery efficiencies of >98% were achieved using the cell impermeable dye calcein (0.6 kDa) as a model payload, while maintaining cell viabilities at >98%. The highly efficient intracellular delivery approach demonstrated in this work will facilitate translational studies targeting molecular screening and drug testing that bridge laboratory and clinical investigations.
Plasmon Heating Promotes Ligand Reorganization on Single Gold Nanorods

Xiaoyu Cheng,Taryn P. Anthony,Claire A. West,Zhongwei Hu,Vignesh Sundaresan,Aaron J. McLeod,David J. Masiello,Katherine A. Willets

DOI: https://doi.org/10.1021/acs.jpclett.9b00079

2019-01-01

Abstract:Single-molecule fluorescence microscopy is used to follow dynamic ligand reorganization on the surface of single plasmonic gold nanorods. Fluorescently labeled DNA is attached to gold nanorods via a gold-thiol bond using a low-pH loading method. No fluorescence activity is initially observed from the fluorescent labels on the nanorod surface, which we attribute to a collapsed geometry of DNA on the metal. Upon several minutes of laser illumination, a marked increase in fluorescence activity is observed, suggesting that the ligand shell reorganizes from a collapsed, quenched geometry to an upright, ordered geometry. The ligand reorganization is facilitated by plasmon-mediated photothermal heating, as verified by controls using an external heat source and simulated by coupled optical and heat diffusion modeling. Using super-resolution image reconstruction, we observe spatial variations in which ligand reorganization occurs at the single-particle level. The results suggest the possibility of nonuniform plasmonic heating, which would be hidden with traditional ensemble-averaged measurements.
A Temperature Microsensor for Measuring Laser-Induced Heating in Gold Nanorods

Dennis B. Pacardo,Bhanu Neupane,Gufeng Wang,Zhen Gu,Glenn M. Walker,Frances S. Ligler

DOI: https://doi.org/10.1007/s00216-014-8222-9

2014-01-01

Abstract:Measuring temperature is an extensively explored field of analysis, but measuring a temperature change in a nanoparticle is a new challenge. Here, a microsensor is configured to measure temperature changes in gold nanorods in solution upon laser irradiation. The device consists of a silicon wafer coated with silicon nitride in which a microfabricated resistance temperature detector was embedded and attached to a digital multimeter. A polydimethylsiloxane mold served as a microcontainer for the sample attached on top of the silicon membrane. This enables laser irradiation of the gold nanorods and subsequent measurement of temperature changes. The results showed a temperature increase of 8 to 10 °C and good correlation with theoretical calculations and bulk sample direct temperature measurements. These results demonstrate the suitability of this simple temperature microsensor for determining laser-induced heating profiles of metallic nanomaterials; such measurements will be essential for optimizing therapeutic and catalytic applications.
Synthesis of Scalable Micro-Droplets with Heat-Driven Effect in Flow-Focusing Device.

Gang Fan,Dan-dan Liu,Xian-ting Ding,Zhi-jun Ma,Jian Yang

DOI: https://doi.org/10.1109/nems.2015.7147394

2015-01-01

Abstract:This paper reports a new method for controlling micro- and nano-droplets by the aid of heat. Computational fluid dynamics (CFD) simulation results suggest this technique is capable of conveniently controlling the droplets sizes down to several micrometers or even nanometers. This pilot research offers the possibility of fabricating micro-droplet with specific size and without changing the fluid. Three factors are studied, including the temperature of continuous phase, the temperature of discrete phase and the temperature gradient on the orifice. The results show that heat transfer between the two phases is fast as characteristic length is in micron level. Increase in temperature can lead to the increase of the droplet radius, wherein the effect of the continuous phase temperature is the most significant.
Nanoscale Control of Temperature Distribution Using a Plasmonic Trimer

Zuwen Liu,Qiang Li,Weichun Zhang,Yuanqing Yang,Min Qiu

DOI: https://doi.org/10.1007/s11468-015-9879-4

IF: 2.726

2015-01-01

Plasmonics

Abstract:A plasmonic trimer composed of three closely packed identical gold nanospheres for manipulating nanoscale temperature distribution is proposed. It is shown that heat can be unevenly distributed among the three particles, creating a high temperature gradient in the nanoscale space despite the strong thermalization effect. Moreover, the difference in temperature increment among the particles is sensitive to the polarization of incident light and can be continuously tuned. The dependence of the achievable temperature difference on the trimer parameters is also investigated. The ability of nanoscale selective heating provides a possible way of remotely manipulating the nanoscale thermally induced physical or chemical processes with unprecedented spatial precision.
Photothermal Heating of Au Nanorods and Nanospheres: Temperature Characteristics and Strength of Convective Forces

Rituraj Borah,Ashish Kumar,Millen Samantaray,Anusha Desai,Fan-Gang Tseng

DOI: https://doi.org/10.1007/s11468-023-01855-4

IF: 2.726

2023-01-01

Plasmonics

Abstract:The nanoscale photothermal effect and the optofluidic convection around plasmonic nanoparticles drive the application of such nanoparticles in micro-environment. In this work, heat transfer and fluid flow around Au nanospheres and nanorods in water medium under continuous and pulsed wave laser irradiance was investigated using an FEM based numerical framework. Au nanospheres of a wide range of diameter: 40 nm ≤ Diameter (D) ≤ 180 nm and relatively large nanorods (diameter: 50 nm) with varying aspect ratio (1 ≤ Aspect ratio (A) ≤ 5) and orientation (0° ≤ θ ≤ 90°, ϕ = 0°, 90°) with respect to the incident EM radiation were investigated for continuous wave (CW) and pulsed wave laser. It was found that although nanorods can attain much higher temperature than nanospheres, orientation of a nanorod is an important factor to be carefully considered in applications. In micro-scale spherical and hemispherical confinements (diameter < 14.4 μm), the convective velocity fields around nanoparticles is in the order of 10–9 m/s, with only a weak effect of the slip or no-slip boundary condition on the confining walls. Importantly, the size of the confinement has a strong effect leading to an order of magnitude stronger convection for 14.4 μm (diameter) spherical confinement as compared to 3.6 μm confinement. Additionally close proximity of the nanoparticles to the confining walls strongly reduces (by an order of magnitude) the convective currents. The results reported herein provides important insights for the use of photothermal nanoparticles in microscale confined space (e.g. cellular environment) for applications such as optical tweezers, photoporation, etc.
Gold Nanoparticle Transfer Through Photothermal Effects in A Metamaterial Absorber by Nanosecond Laser

Hanmo Gong,Yuanqing Yang,Xingxing Chen,Ding Zhao,Xi Chen,Yiting Chen,Min Yan,Qiang Li,Min Qiu

DOI: https://doi.org/10.1038/srep06080

IF: 4.6

2014-01-01

Scientific Reports

Abstract:A non-complicated, controllable method of metallic nanoparticle fabrication at low operating light power is proposed. The method is based on laser-induced forward transfer, using a metamaterial absorber as the donor to significantly enhance the photothermal effect and reduce the operating light fluence to 35 mJ/cm(2), which is much lower than that in previous works. A large number of metallic nanoparticles can be transferred by one shot of focused nanosecond laser pulses. Transferred nanoparticles exhibit good size uniformity and the sizes are controllable. The optical properties of transferred particles are characterized by dark-field spectroscopy and the experimental results agree with the simulation results.
Theoretical and experimental investigations on the photothermal effect of gold nanorods irradiated by femtosecond and nanosecond laser

Dong Li,Penghui Zhao,Jing Feng,Linzhuang Xing,Bin Chen,Dingying Liao

DOI: https://doi.org/10.2298/tsci210828327l

IF: 1.971

2021-01-01

Thermal Science

Abstract:Nanoparticle-mediated laser-induced breakdown (LIB) can be used for Nanoparticle synthesis, cell nanosurgery and laser-induced breakdown spectroscopy (LIBS). To investigate the photo-thermal conversion of gold nanoparticles during pulsed laser irradiation, the electron-phonon two-temperature model was established in this study. The impact of laser energy density and pulse width on the thermal conversion and morphology change of gold nanorods were investigated and compared with experimental observations. The results show that the melting threshold of gold nanorods under nanosecond laser irradiation is about twenty times that of femtosecond laser irradiation. The mechanisms of nanorod fragmentation are different between fem to and nanosecond laser irradiation: particle melting is more likely to occur in nanosecond laser irradiation, while the Coulomb explosion is highly likely to occur in femtosecond laser irradiation.

thermodynamics
Resonant Scattering-Enhanced Photothermal Microscopy

Qiang Li,Zhonghong Shi,Lijun Wu,Hong Wei

DOI: https://doi.org/10.1039/c9nr10893a

IF: 6.7

2020-01-01

Nanoscale

Abstract:Photothermal (PT) microscopy is currently the most efficient approach for the detection and spectroscopy of individual non-fluorescent nano-objects based solely on their absorption. The nano-objects in current PT microscopy are usually non-resonant with the probe laser light, and the PT signal is mainly generated from the interactions of the incident probe light and the heating light-induced thermal lens around the imaged object. Inspired by the high sensitivity of the scattering field from the nano-objects near optical resonance to the variation in the local refractive index, we developed a novel strategy of resonant scattering-enhanced PT microscopy where the imaged nano-objects are near-resonant with the probe laser light. We have demonstrated this by using gold nanorods (NRs) with tunable longitudinal surface plasmon resonances. The PT signal of gold NR near-resonant with the probe light showed dramatic variation in the narrow resonance wavelength range, as small as 15 nm, and the maximal amplitude of the PT signal in this range can be enhanced up to 43 times as compared with the weak PT signal of gold NR non-resonant with the probe light. Theoretical analysis indicates that the obtained strong PT signal is mainly caused by the heat-induced variation in the polarizability of gold NR. Our novel work demonstrates the first resonant scattering-enhanced PT imaging of plasmonic nanoparticles, paving the way for the development of PT microscopy with ultra-high sensitivity toward the sensing, imaging, and spectroscopy of nanoscopic objects in complex environments.
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms

Piotr Radomski,Federica Zaccagnini,Paweł Ziółkowski,Francesca Petronella,Luciano De Sio,Aimad Koulali,Dariusz Mikielewicz

DOI: https://doi.org/10.3390/en17112587

IF: 3.2

2024-05-27

Energies

Abstract:Achieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion and allowing the maximum temperature to be reached faster. This work examines the energy conversion in sandwiched glassy platforms with gold nanorods. The platforms are kept vertically in the air and illuminated by a 0.5 W near-infrared laser (808 nm). To describe this aspect theoretically, the size and conversion efficiency of the electromagnetic properties are compromised between the proposed model and the stability of the nanorods. As a research approach, our model of cross-sections and polarizability for the surface effect is proposed, coupled with classical CFD numerical calculations. The results of the proposed model, validated by a thermal camera and spectroscopy measurements, indicate that as long as the energy conversion is visible with relatively low-power lasers (ΔT = 18.5 °C), the platforms do not offer fast heat dissipation. The results indicate that, despite the flow forcing by the air inflow, the entropy generation due to heat conduction is more than three orders higher than the dynamic entropy production. Flow forcing corresponds to the value of the velocity for classical convective motions. Therefore, the delivered heat flux must be distributed via convective transport or the associated high-conductive materials.

energy & fuels
Optofluidic Convection Around Au Nanorods and Nanospheres by Photothermal Heating: Effect of Nanoparticle Geometry and Boundary Conditions

Rituraj Borah,Millen Samantaray,Ashish Kumar,Anusha Desai,Fan-Gang Tseng

DOI: https://doi.org/10.26434/chemrxiv-2022-s16mm

2022-01-01

Abstract:Laser mediated heat transfer and optofluidic nano-scale convection can be exploited in the photothermal applications of plamonic nanoparticles in different micro-environment. In this work, heat transfer and fluid flow around Au nanospheres and nanorods in water medium under continuous and pulsed wave laser irradiance was investigated using an FEM based numerical framework. Au nanospheres of a wide range of diameter: 40 nm ≤ Diameter (D) ≤ 180 nm and nanorods with varying aspect ratio (1 ≤ Aspect ratio (A) ≤ 5) and orientation (0o ≤ θ ≤ 90o, ϕ = 0o, 90o) with respect to the incident EM radiation were investigated for continuous wave (CW) and pulsed wave laser. Relatively large Au nanorods dimensions similar to the models were also synthesized. The numerical results were validated by comparison with the experimental optical cross-section of the synthesized nanorods. It was found that although nanorods can attain much higher temperature than nanospheres, orientation of a nanorod is an important factor to be carefully considered in applications. In micro-scale spherical and hemispherical confinements (diameter < 14.4 μm) convective velocity fields around nanoparticles were determined for slip and no-slip condition on the confining walls. It was found that slip boundary condition on the confining walls has a moderate effect on the strength of the flow field. While, the effect of the proximity of the nanoparticle from the walls is considerable.
Plasmonic Enhanced Photothermal Effects and Its Applications.

Min Qiu,Xi Chen,Yuechun Shi,Yiting Chen,Hanmo Gong,Ding Zhao,Xingxing Chen,Yuanqing Yang,Min Yan,Qiang Li

DOI: https://doi.org/10.1109/icton.2014.6876429

2014-01-01

Abstract:We review here our recent studies on plasmonic enhanced photothermal effects in metallic nanostructure, and the applications of such effects. When light is shined on a prefect metamaterial absorber patterned with e-beam lithography, the gold nanoparticles (NPs) forming the absorber can be either transformed to nano-spherical-domes, or to truncated-octahedral shaped or multi-twined nanocrystals with large crystal grain sizes and flat boundary facets. The evolution of morphology and crystallinity of the gold NPs can be also observed. Evidences clearly show that the surface melting and the coalescence mechanism play a key role on nanocrystals formation. These melted gold nanospheres can even be transferred to another substrate, on which the transferred NPs exhibit excellent size uniformity. The strong photothermal effects can also be utilized to tune silicon photonics waveguides and resonators. It is shown that all-optical photothermal switching of Mach-Zehnder interferometers (MZI), silicon disk resonators, and silicon ring resonators is possible with the help of plasmonic nanoheaters. The switching response time and power consumption are all at reasonably low level.
Fiber Coupled Near‐Field Thermoplasmonic Emission from Gold Nanorods at 1100 K

Jiayu Li,Jeffrey Wuenschell,Zhuo Li,Subhabrata Bera,Kai Liu,Renhong Tang,Henry Du,Paul R. Ohodnicki,Sheng Shen

DOI: https://doi.org/10.1002/smll.202007274

IF: 13.3

2021-03-14

Small

Abstract:<p>Nanostructured gold has attracted significant interest from materials science, chemistry, optics and photonics, and biology due to their extraordinary potential for manipulating visible and near‐infrared light through the excitation of plasmon resonances. However, gold nanostructures are rarely measured experimentally in their plasmonic properties and hardly used for high‐temperature applications because of the inherent instability in mass and shape due to the high surface energy at elevated temperatures. In this work, the first direct observation of thermally excited surface plasmons in gold nanorods at 1100 K is demonstrated. By coupling with an optical fiber in the near‐field, the thermally excited surface plasmons from gold nanorods can be converted into the propagating modes in the optical fiber and experimentally characterized in a remote manner. This fiber‐coupled technique can effectively characterize the near‐field thermoplasmonic emission from gold nanorods. A direct simulation scheme is also developed to quantitively understand the thermal emission from the array of gold nanorods. The experimental work in conjunction with the direct simulation results paves the way of using gold nanostructures as high‐temperature plasmonic nanomaterials, which has important implications in thermal energy conversion, thermal emission control, and chemical sensing.</p>

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Heat Transfer and Thermocapillary Flow of a Double-Emulsion Droplet Heated Using an Infrared Laser by the Photothermal Effect: a Numerical Study

Zhibin Wang,Hongshi Su,Ying Chen,Yuxiu Li,Shuzhe Li

DOI: https://doi.org/10.1007/s12217-021-09868-6

2021-07-24

Microgravity Science and Technology

Abstract:Using a laser to heat microfluid has the advantages of non-contact local operation, high accuracy, and good adjustability. In this study, a focused infrared laser with a 1550-nm wavelength was applied to heat an oil–water-oil double-emulsion droplet in a microchannel. The Finite Volume Method was used to numerically study the thermocapillary flow and heat transfer of this laser-heating process. In the simulation, the laser energy distribution was modeled using a volumetric Gaussian heat source. The attention was focused on the heat transfer and thermocapillary flow of the double-emulsion droplet. The influences of laser parameters (power and beam diameter) and the temperature coefficient of interfacial tension were studied. We found that the intensity of the thermocapillary flow and the temperature linearly increased with input power; they first decreased and then increased as the size of the input beam increased because of the combined effect of absorbing energy and energy concentration. Moreover, there were four and two thermocapillary vortices inside the middle water phase when the sign of the temperature coefficient of interfacial tension in the double interfaces was the same and different, respectively. In all cases, the uneven temperature coefficient of the inner droplet was lower than that of the middle water phase, but the average temperatures of both regions were extremely close. These results can prove useful in the future operation of double-emulsion droplet-based microfluidics using a laser as a precise and sensitive heating source for drug discovery and delivery, cell analyses, and micro/nanoparticle synthesis.

thermodynamics,mechanics,engineering, aerospace
In Situ Shape Control of Thermoplasmonic Gold Nanostars on Oxide Substrates for Hyperthermia-Mediated Cell Detachment

Gail A. Vinnacombe-Willson,Naihao Chiang,Leonardo Scarabelli,Yuan Hu,Liv K. Heidenreich,Xi Li,Yao Gong,Derek T. Inouye,Timothy S. Fisher,Paul S. Weiss,Steven J. Jonas

DOI: https://doi.org/10.1021/acscentsci.0c01097

IF: 18.2

2020-10-23

ACS Central Science

Abstract:Gold nanostars (AuNSTs) are biocompatible, have large surface areas, and are characterized by high near-infrared extinction, making them ideal for integration with technologies targeting biological applications. We have developed a robust and simple microfluidic method for the direct growth of anisotropic AuNSTs on oxide substrates including indium tin oxide and glass. The synthesis was optimized to yield AuNSTs with high anisotropy, branching, uniformity, and density in batch and microfluidic systems for optimal light-to-heat conversion upon laser irradiation. Surface-enhanced Raman scattering spectra and mesoscale temperature measurements were combined with spatially correlated scanning electron microscopy to monitor nanostar and ligand stability and microbubble formation at different laser fluences. The capability of the platform for generating controlled localized heating was used to explore hyperthermia-assisted detachment of adherent glioblastoma cells (U87-GFP) grafted to the capillary walls. Both flow and laser fluence can be tuned to induce different biological responses, such as ablation, cell deformation, release of intracellular components, and the removal of intact cells. Ultimately, this platform has potential applications in biological and chemical sensing, hyperthermia-mediated drug delivery, and microfluidic soft-release of grafted cells with single-cell specificity.Plasmonic gold nanostars grown in situ by seed-mediated synthesis in microfluidic channels are used to probe individual cells and to convert near-infrared light to heat to release them selectively.This article has not yet been cited by other publications.

chemistry, multidisciplinary
Selecting High-Performance Gold Nanorods for Photothermal Conversion

Túlio de L Pedrosa,Sajid Farooq,Renato E de Araujo

DOI: https://doi.org/10.3390/nano12234188

2022-11-25

Abstract:In this work, we establish a new paradigm on identifying optimal arbitrarily shaped metallic nanostructures for photothermal applications. Crucial thermo-optical parameters that rule plasmonic heating are appraised, exploring a nanoparticle size-dependence approach. Our results indicate two distinct figures of merit for the optimization of metallic nanoheaters, under both non-cumulative femtosecond and continuum laser excitation. As a case study, gold nanorods are evaluated for infrared photothermal conversion in water, and the influence of the particle length and diameter are depicted. For non-cumulative femtosecond pulses, efficient photothermal conversion is observed for gold nanorods of small volumes. For continuous wave (CW) excitation at 800 nm and 1064 nm, the optimal gold nanorod dimensions (in water) are, respectively, 90 × 25nm and 150 × 30 nm. Figure of Merit (FoM) variations up to 700% were found considering structures with the same peak wavelength. The effect of collective heating is also appraised. The designing of high-performance plasmonic nanoparticles, based on quantifying FoM, allows a rational use of nanoheaters for localized photothermal applications.
Investigation of Impact and Spreading of Molten Nanosized Gold Droplets on Solid Surfaces.

Daozhi Shen,Guisheng Zou,Lei Liu,Aiping Wu,Walter W. Duley,Y. Norman Zhou

DOI: https://doi.org/10.1364/ao.57.002080

IF: 1.9

2018-01-01

Applied Optics

Abstract:Understanding the impact dynamics and spreading of molten nanosized droplets on a solid surface is a crucial step towards the design and control of nano-fabrication in many novel applications of nanotechnology. In this context, molecular dynamic (MD) simulations have been conducted to compute temperature and dynamic contact angles of nano-droplets during impact. The evolution of the morphology of a molten metallic nano-droplet impacting on a substrate has been studied using a combination of experimental and simulation techniques. Femtosecond lasers have been used to transfer nanosized gold droplets. Droplet morphology calculated in MD simulations is found to be in good agreement with that seen in scanning electron microscopy (SEM) images. It is found that the spreading of nanoscale molten gold droplets upon impact is enhanced by increasing the droplet impact energy. As observed in experimental data, MD simulation results show that a high droplet-substrate heat transfer rate together with increased wettability of the substrate facilitates spreading and results in a thinner metal deposit after solidification.
Imaging the transient heat generation of individual nanostructures with a mechanoresponsive polymer

Xueqin Chen,Qing Xia,Yue Cao,Qianhao Min,Jianrong Zhang,Zixuan Chen,Hong-Yuan Chen,Jun-Jie Zhu

DOI: https://doi.org/10.1038/s41467-017-01614-0

IF: 16.6

2017-01-01

Nature Communications

Abstract:Measuring the localized transient heat generation is critical for developing applications of nanomaterials in areas of photothermal therapy (PTT), drug delivery, optomechanics and biological processes engineering. However, accurate thermometry with high spatiotemporal resolution is still a challenge. Here we develop a thermosensitive polymer-capped gold nanorod (AuNRs@pNIPAAm), which has temperature-dependent local surface plasmon resonance spectra due to the submolecular conformational change of pNIPAAm molecules. We measure the conformational dynamics on individual gold nanorods at the milliseconds level by the developed spatiotemporal resolution plasmonic spectroscopy (SRPS) and find that it has a fast (<4 ms), linear and reversible mechanoresponse to temperature changes as small as 80 mK. The rapid and highly sensitive thermosensitive AuNRs@pNIPAAm opens a new way to achieve spatiotemporal thermometry for potential applications in PTT and other biological research.
Local Enhancement of lipid membrane permeability induced by irradiated gold nanoparticles

Andrea Torchi,Federica Simonelli,Riccardo Ferrando,Giulia Rossi

DOI: https://doi.org/10.48550/arXiv.1711.07232

2017-11-20

Abstract:Photothermal therapies are based on the optical excitation of plasmonic nanoparticles in the biological environment. The effects of the irradiation on the biological medium depend critically on the heat transfer process at the nanoparticle interface, on the temperature reached by the tissues as well as on the spatial extent of temperature gradients. Unfortunately, both the temperature and its biological effects are difficult to be probed experimentally at the molecular scale. Here, we approach this problem using nonequilibrium molecular dynamics simulations. We focus on photoporation, a photothermal application based on the irradiation of gold nanoparticles by single, short-duration laser pulses. The nanoparticles, stably bound to cell membranes, convert the radiation into heat, inducing transient changes of membrane permeability. We make a quantitative prediction of the temperature gradient around the nanoparticle upon irradiation by typical experimental laser fluences. Water permeability is locally enhanced around the NP, in an annular region that extends only a few nm far from the nanoparticle interface. We correlate the local enhancement of permeability at the NP-lipid interface to the temperature inhomogeneities of the membrane and to the consequent availability of free volume pockets within the membrane core.

Computational Physics,Biological Physics

Local Heating of Individual Droplets Using Photothermal Effects of Gold Nanorods

Gold nanorod-facilitated localized heating of droplets in microfluidic chips.

Photothermal Intracellular Delivery Using Gold Nanodisk Arrays.

Plasmon Heating Promotes Ligand Reorganization on Single Gold Nanorods

A Temperature Microsensor for Measuring Laser-Induced Heating in Gold Nanorods

Synthesis of Scalable Micro-Droplets with Heat-Driven Effect in Flow-Focusing Device.

Nanoscale Control of Temperature Distribution Using a Plasmonic Trimer

Photothermal Heating of Au Nanorods and Nanospheres: Temperature Characteristics and Strength of Convective Forces

Gold Nanoparticle Transfer Through Photothermal Effects in A Metamaterial Absorber by Nanosecond Laser

Theoretical and experimental investigations on the photothermal effect of gold nanorods irradiated by femtosecond and nanosecond laser

Resonant Scattering-Enhanced Photothermal Microscopy

Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms

Optofluidic Convection Around Au Nanorods and Nanospheres by Photothermal Heating: Effect of Nanoparticle Geometry and Boundary Conditions

Plasmonic Enhanced Photothermal Effects and Its Applications.

Fiber Coupled Near‐Field Thermoplasmonic Emission from Gold Nanorods at 1100 K

Heat Transfer and Thermocapillary Flow of a Double-Emulsion Droplet Heated Using an Infrared Laser by the Photothermal Effect: a Numerical Study

In Situ Shape Control of Thermoplasmonic Gold Nanostars on Oxide Substrates for Hyperthermia-Mediated Cell Detachment

Selecting High-Performance Gold Nanorods for Photothermal Conversion

Investigation of Impact and Spreading of Molten Nanosized Gold Droplets on Solid Surfaces.

Imaging the transient heat generation of individual nanostructures with a mechanoresponsive polymer

Local Enhancement of lipid membrane permeability induced by irradiated gold nanoparticles