Abstract:In this work, we report the evolution behavior of Fe and Fe-rich phases in the high-Fe concentration recycled Al-Si-Mg aluminum melt with and without alloying elements (Mn, Cr, Co) introduced. Firstly, the thermodynamic calculations reveal that the addition of Mn, Cr, and Co could improve the nucleation temperature of the Fe-rich phase. Moreover, four solidified ingots for Al-10Si-0.5Mg-1Fe alloy(base alloy) and the base alloy with 1.3 wt% Mn, 0.8 wt% Cr, and 0.8 wt% Co added, respectively, were prepared by holding the melt for 30 min at 610 °C after all the raw materials were fully melted. Microstructure examination revealed that the addition of Co resulted in the formation of the needle-like Fe-rich phase, which further leads to a poor settling effect and low iron removal efficiency. In contrast, the addition of Mn and Cr favors converting β-AlFeSi into α-AlFeMnSi, and forming the Chinese script and fish-bone Fe-rich phase. The size of the Fe-rich phase formed after adding Cr is smaller, while the residual Fe content after adding Mn is less. Also, the sludge phase at the bottom of the ingot presents a polygonal shape and long rod shape after adding Mn and Cr, respectively. Further, the Mn alloying increases the particle size of the sludge, while Cr refines the sludge phase and increases the aspect ratio (length/width ratio) of the sludge. Particularly, for Al-Si-Mg alloy with 1.0% Fe content, the superior mechanical properties are obtained by adding 0.8 wt% Cr, and the tensile strength reaches 136 MPa. After adding 1.3 wt% Mn, the Fe content of the upper section is reduced to 0.37 wt%, and the Fe removal rate achieves 63%. The obtained results provide some guidelines for achieving high iron separation efficiency in recycled aluminum-silicon alloy melts.

The Role of Fe on the Grain Refinement of High Purity Aluminium

Effect of Fe on Grain Refinement of Commercial Purity Aluminum

Effect of Fe and Si on Grain Refinement of Commercial Purity Aluminum

Effect of Fe on Grain Refining of Pure Aluminum Refined by Al5tib Master Alloy

Influence of Fe on grain nucleation and growth of pure aluminum during refining by Al-Ti-B and Al-Ti-C master alloys

Grain Refinement of Al-5Ti-0.62C-0.2Nd Grain Refiner for Commercial Pure Aluminum and Its Effect on Mechanical Properties

The grain refinement of high-purity aluminum by aluminum-transition metal alloys

Development of Grain Refinement in Aluminium Field

Performance Comparison of AlTiC and AlTiB Master Alloys in Grain Refinement of Commercial and High Purity Aluminum

On the Understanding of Aluminum Grain Refinement by Al-Ti-B Type Master Alloys

Grain refinement and mechanical properties of Mg–5Li–3Al alloy inoculated by Al–5Ti–1B master alloy

Effects of High Quality Al-5Ti-1B Alloy wire on Grain Refinement of Pure Al

Grain Refinement in A Alznmgcuti Alloy by Intensive Melt Shearing: A Multi-Step Nucleation Mechanism

Effects of Manganese And/Or Carbon on the Grain Refinement of Mg-3al Alloy

Research of Grain Refining on Pure Al by Three Different Master Alloys

Study on Grain Refining and Metamorphism of ZL111 Aluminium Alloys

A qualitative and quantitative investigation of nonmetallic inclusions in molten Al–Mg, Al–Cu, and Al–Zn–Mg–Cu alloys

On Grain Coarsening and Refining of the Mg–3Al Alloy by Sm

Efficiency of different commercial TiBAl grain refiners on refinement of pure aluminum cast structures

Evolution behavior of Fe and Fe-rich phases in high-Fe concentration Al-Si-Mg alloy with Mn, Cr, and Co alloyed

Quantifying the effects of grain refiners (AlTiB and Y) on microstructure and properties in W319 alloys