Abstract:Abstract The aerodynamic performance of conventional aircraft configurations are mainly affected by the wing and horizontal tail. Drag reduction by shape optimisation of the wing, while taking into account the aircraft trimmed constraint, has more benefit than focusing solely on the wing. So in order to evaluate this approach, the following study presents results of a single and multipoint aerodynamic shape optimisation of the wing-body-tail configuration, defined by the Aerodynamic Design Discussion Group (ADODG). Most of the aerodynamic shape optimisation problems published in the last years are focused mainly on the wing as the main driver for performance improvement, with no trim constraint and/or excess drag obtained from the fuselage, fins or other parts. This work partially fills this gap by an investigation of RANS-based aerodynamic optimisation for transonic trimmed flight. Mesh warping and geometry parametrisation is accomplished by fitting the multi-block structured grid to a B-spline volumes and performing the mesh movement by using surface control points embedded within the free-form deformation (FFD) volumes. A gradient-based optimisation algorithm is used with an adjoint method in order to compute the derivatives of the objective and constraint functions with respect to the design variables. In this work the aerodynamic shape optimisation of the CRM wing-body-tail configuration is investigated, including a trim constraint that is satisfied by rotating the horizontal tail. The shape optimisation is driven by 432 design variables that envelope the wing surface, and 120 shape variables for the tail, as well as the angle of attack and tail rotation angles. The constraints are the lift coefficient, wing’s thickness controlled by 1,000 control points, and the wing’s volume. For the untrimmed configuration the drag coefficient is reduced by 5.76%. Optimising the wing with a trim condition by tail rotation results in shock-free design with a considerably improved drag, even better than the untrimmed-optimised case. The second optimisation problem studied is a single and multi-point lift constraint drag minimisation of a gliding configuration wing in transonic viscous flow. The shock is eliminated, reducing the drag of the untrimmed configuration by more than 60%, using 192 design variables. Further robustness is achieved through a multi-point optimisation with more than 45% drag reduction.

Trim induced drag analysis and optimization of elastic twin-tailboom aircraft

INDUCED DRAG REDUCTION OPTIMIZATION STUDY USING MULTI-CONTROL SURFACES FOR ELASTIC WING

Effects of Static Stability Margin on Aerodynamic Design Optimization of Truss-Braced Wing Aircraft

Numerical investigations on drag reduction of a civil light helicopter fuselage

Optimal Selection of Active Jet Parameters for a Ducted Tail Wing Aimed at Improving Aerodynamic Performance

Adjoint-based aerodynamic drag minimisation with trim penalty

An efficient implementation of aeroelastic tailoring based on efficient computational fluid dynamics-based reduced order model

Aerodynamic Shape Optimization of Subsonic/Supersonic Flows Integrating Variable-Fidelity Longitudinal Trim Analysis

Rotor Cross-Tilt Optimization of Manned Multi-rotor Evtol Aircraft for Yaw Control Efficiency

Comprehensive Research on Vibration Characteristics, Strength and Stability of T-tail

Longitudinal Attitude Control and Stability Analysis for a Low Aspect Ratio Flying Wing UAV at High Angle of Attack

An Automated Aeroelastic Performance Prediction Method in Time Domain for Transonic Aeroelastic Tailoring

Application of Aeroelastic Tailoring for Load Alleviation on a Flying Demonstrator Wing

A Novel Control Allocation Method for Yaw Control of Tailless Aircraft

Fuel Efficiency Optimization of High-Aspect-ratio Aircraft Via Variable Camber Technology Considering Aeroelasticity

An Efficient Implementation of Transonic Aeroelastic Tailoring based on a Reduced-Order Model using Structural Dynamic Reanalysis Method

Preliminary Design and Optimization of Primary Structures for a Tilt-Duct UAV

Aerodynamic Optimization Design of Duct Body Structure for Coaxial Rotor Unmanned Aerial Vehicles

Conceptual Aircraft Empennage Design Based on Multidisciplinary Design Optimization Approach

Development of Response Surface Model of Endurance Time and Structural Parameter Optimization for a Tailsitter UAV

Numerical investigation of angle parameters of tip sails for improvement of aircraft flight performance